No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring User-Side Multicast for IPoE Access Users

Example for Configuring User-Side Multicast for IPoE Access Users

This section provides an example for configuring user-side multicast service for Internet Protocol over Ethernet (IPoE) access users.

Networking Requirements

On the network shown in Figure 14-7, users (with PC1 and PC2) are IPoE access users, and they want to join multicast programs. Configure user-side multicast to implement user-based on-demand multicast data forwarding.

Figure 14-7 Configuring user-side multicast for IPoE access users
NOTE:

Interface 1 and interface 2 in this example stand for GE 1/0/0 and GE 1/0/1.1, respectively.



Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure an IPv4 address pool.

  2. Configure Authentication, Authorization and Accounting (AAA) schemes.

  3. Configure a user domain.

  4. Configure the IPoE access mode:

    1. Configure an authentication scheme.

    2. Bind a sub-interface to a VLAN.

    3. Configure a BAS interface and specify a user access type for the interface. (The interface can be a main, a common sub-interface, or a QinQ sub-interface. A common sub-interface is used in the example.)

  5. Enable session-based multicast traffic replication on a BAS interface.

  6. Configure basic multicast functions:

    1. Enable multicast routing.

    2. Enable Protocol Independent Multicast-Sparse Mode (PIM-SM) on all BRAS interfaces.

    3. Enable IGMP on the BRAS interface connected to users.

Data Preparation

  • IPv4 address pool

  • Authentication and accounting schemes

  • User domain
  • BAS interface parameters

Procedure

  1. Configure an IPv4 address pool.

    <HUAWEI> system-view
    [HUAWEI] sysname BRAS
    [*HUAWEI] commit
    [~BRAS] ip pool ipv4 bas local
    [*BRAS-ip-pool-ipv4] gateway 4.0.0.1 255.255.0.0
    [*BRAS-ip-pool-ipv4] section 1 4.0.0.1 4.0.255.255
    [*BRAS-ip-pool-ipv4] quit
    [*BRAS] commit

  2. Configure AAA schemes.

    # Configure an authentication scheme.

    [~BRAS] aaa
    [*BRAS-aaa] authentication-scheme none
    [*BRAS-aaa-authen-none] authentication-mode none
    [*BRAS-aaa-authen-none] quit
    [*BRAS-aaa] commit

    # Configure an accounting scheme.

    [~BRAS-aaa] accounting-scheme none
    [*BRAS-aaa-accounting-none] accounting-mode none
    [*BRAS-aaa-accounting-none] quit
    [*BRAS-aaa] quit
    [*BRAS] commit

  3. Configure a domain.

    [~BRAS] aaa
    [*BRAS-aaa] domain ipv4
    [*BRAS-aaa-domain-ipv4] authentication-scheme none
    [*BRAS-aaa-domain-ipv4] accounting-scheme none
    [*BRAS-aaa-domain-ipv4] ip-pool ipv4
    [*BRAS-aaa-domain-ipv4] quit
    [*BRAS-aaa] quit
    [*BRAS] commit

  4. Bind a sub-interface to a VLAN.

    [~BRAS] interface gigabitethernet 1/0/1.1
    [*BRAS-GigabitEthernet1/0/1.1] user-vlan 2
    [*BRAS-GigabitEthernet1/0/1.1-vlan-2-2] quit
    [*BRAS-GigabitEthernet1/0/1.1] commit

  5. Configure a BAS interface and specify a user access type for the interface, and configure an authentication scheme.

    [~BRAS-GigabitEthernet1/0/1.1] bas
    [*BRAS-GigabitEthernet1/0/1.1-bas] access-type layer2-subscriber default-domain authentication ipv4
    [*BRAS-GigabitEthernet1/0/1.1-bas] authentication-method bind
    [*BRAS-GigabitEthernet1/0/1.1-bas] quit
    [*BRAS-GigabitEthernet1/0/1.1] commit
    # Run the display access-user domain ipv4 command to display online user information. The command output shows that users with ID 352 and 353 accessed the Internet through IPoE.
    [~BRAS] display  access-user domain ipv4
      ------------------------------------------------------------------------------
      UserID  Username                Interface      IP address       MAC
              Vlan          IPv6 address             Access type
      ------------------------------------------------------------------------------
      352     BRAS-01008000100000...  GE1/0/1.1      4.0.1.2          0001-010a-0101
              1/-           -                        IPOE
      353     BRAS-01008000300002...  GE1/0/1.1      4.0.1.3          000c-0101-0101
              3/2           -                        IPOE
      ------------------------------------------------------------------------------
      Normal users                       : 2
      RUI Local users                    : 0
      RUI Remote users                   : 0
      Total users                        : 2
    

  6. Enable session-based multicast traffic replication on a BAS interface.

    [~BRAS-GigabitEthernet1/0/1.1] bas
    [*BRAS-GigabitEthernet1/0/1.1-bas] multicast copy by-session
    [*BRAS-GigabitEthernet1/0/1.1-bas] quit
    [*BRAS-GigabitEthernet1/0/1.1] quit
    [*BRAS] commit

  7. Configure basic multicast functions.

    [~BRAS] multicast routing-enable
    [*BRAS] interface gigabitethernet 1/0/0
    [*BRAS-GigabitEthernet1/0/0] undo shutdown
    [*BRAS-GigabitEthernet1/0/0] ip address 10.1.1.1 255.255.255.0
    [*BRAS-GigabitEthernet1/0/0] pim sm
    [*BRAS-GigabitEthernet1/0/0] quit
    [*BRAS] commit
    [~BRAS] interface gigabitethernet 1/0/1.1
    [*BRAS-GigabitEthernet1/0/1.1] pim sm
    [*BRAS-GigabitEthernet1/0/1.1] igmp enable
    [*BRAS-GigabitEthernet1/0/1.1] quit
    [*BRAS] commit

  8. Verify the configuration.

    # Run the display multicast group-ip command to display information about users of a specified multicast group. The command output shows that users with ID 352 and 353 joined multicast programs whose group address is 225.0.0.1.
    [~BRAS] display multicast group-ip 225.0.0.1 out-interface GigabitEthernet 1/0/1.1
      User ID    User IP                     User type    Interface
    
      352        4.0.1.2                     Local        GigabitEthernet1/0/1.1
      353        4.0.1.3                     Local        GigabitEthernet1/0/1.1
    
      Local user number :2
      Remote user number:0
      Total user number :2     
    # Run the display multicast user-id command to check the multicast programs that a specified user joined on a BAS interface.
    [~BRAS] display multicast user-id 353
      User information:
      User ID             :353
      User IPv4 address   :4.0.1.3
      Gateway IPv4 address:4.0.0.1
      BRAS interface      :GigabitEthernet1/0/1.1
      User MAC-address    :000c-0101-0101
      MAX program list    :4
    
      User order program:
      Group IP           Source IP
      225.0.0.1          0.0.0.0
    
      Total:1                       
    # Run the display pim routing-table command to display PIM routing entries.
    [~BRAS] display pim routing-table
     VPN-Instance: public net
     Total 1 (*, G) entry; 1 (S, G) entry
    
     (*, 225.0.0.1)
         RP: NULL
         Protocol: pim-sm, Flag: WC NIIF
         UpTime: 01:37:51
         Upstream interface: NULL
             Upstream neighbor: NULL
             RPF prime neighbor: NULL
         Downstream interface(s) information:
         Total number of downstreams: 1
            1: GigabitEthernet1/0/1(bas)
                 Protocol: igmp, UpTime: 01:37:51, Expires: -
    
     (10.1.1.100, 225.0.0.1)
         RP: NULL
         Protocol: pim-sm, Flag: SPT LOC ACT
         UpTime: 04:34:52
         Upstream interface: GigabitEthernet1/0/0
             Upstream neighbor: NULL
             RPF prime neighbor: NULL
         Downstream interface(s) information:
         Total number of downstreams: 1
            1: GigabitEthernet1/0/1(bas)
                 Protocol: pim-sm, UpTime: 01:37:51, Expires: -  

Configuration Files

#
sysname BRAS
#
multicast routing-enable
#
ip pool ipv4 bas local
 gateway 4.0.0.1 255.255.0.0
 section 1 4.0.0.1 4.0.255.255
#
aaa
 #
 authentication-scheme none
  authentication-mode none
 #
 accounting-scheme none
  accounting-mode none
 #
 domain ipv4
  authentication-scheme none
  accounting-scheme none
  ip-pool ipv4
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 10.1.1.1 255.255.255.0
 pim sm
#
interface GigabitEthernet1/0/1.1
 user-vlan 2 
 pim sm
 igmp enable
 bas
 #
  access-type layer2-subscriber default-domain authentication ipv4
  authentication-method bind
  multicast copy by-session
#
return  
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 39678

Downloads: 97

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next