No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Static Router Ports

Configuring Static Router Ports

Static router ports can be configured to enable users to regularly receive multicast data packets because static router ports do not age.

Context

Router ports receive multicast data packets from an upstream device, and are enabled as dynamic by default. However, static router ports can be configured to allow users to regularly receive multicast data packets. Since static router ports do not age, multicast services are not interrupted.

On a stable network, PW interfaces and sub-interfaces in a VPLS or interfaces in a VLAN can be configured as static router ports.

Static router ports do not age, and can only be deleted using relevant commands.

Procedure

  • Static router ports can be configured at different interface types on a network to ensure regular multicast traffic reception. The steps listed in Table 18-3 can be performed in any order. Complete one or more steps as required to configure static router ports.

    Table 18-3 Configuring static router ports

    Network Type

    Interface Type

    Configuration Procedure

    Description

    VLAN

    Interface

    1. Run the system-view command to enter the system view.
    2. Run the interface interface-typeinterface-number command to enter the Ethernet interface view.
    3. Run the igmp-snooping static-router-port vlan vlan-id command to configure the interface as a static router port.
    4. Run the commit command to commit the configuration.

    Before configuring the interface as a static router port, ensure that the interface has been added to a specific VLAN. Otherwise, the configuration will not take effect.

    VPLS

    Sub-interface

    1. Run the system-view command to enter the system view.
    2. Run the interface interface-type interface-number.subnumber command to enter the sub-interface view.
    3. Run the l2 binding vsi vsi-name command to bind the sub-interface to a VSI.
    4. Run the igmp-snooping static-router-port vsi vsi-name command to configure the sub-interface as a static router port in the VSI.
    5. Run the commit command to commit the configuration.
    • A sub-interface that is not bound to a VSI cannot be configured as a static router port.
    • If a sub-interface configured as a static router port becomes unbound from a VSI, all static router port configurations will be deleted from the sub-interface.

    The sub-interface can be a common sub-interface or a Dot1q termination sub-interface.

    PW

    1. Run the system-view command to enter the system view.
    2. Run the vsi vsi-name [ static ] command to enter the VSI view.
    3. Run the igmp-snooping static-router-port remote-peer ip-address [ negotiation-vc-id vc-id | bgp-ad ] command to configure a PW interface as a static router port in the VSI.
    4. Run the commit command to commit the configuration.
    Configure the static router port according to the signaling protocol:
    • If LDP is used as a signaling negotiation protocol, run the igmp-snooping static-router-port remote-peer ip-address [ negotiation-vc-id vc-id] command to configure a PW interface as a static router port in a VSI.

    • If BGP-AD is used as the signaling negotiation protocol, run the igmp-snooping static-router-port remote-peer ip-address bgp-ad command to configure a PW interface as a static router port in a VSI.

    If no IP address is set for the remote peer, the PW interface can still be configured as a static router port in the VSI, but the configuration will not take effect. It will only take effect after an IP address is set for the remote peer.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 42733

Downloads: 97

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next