No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - QoS 01

This is NE40E V800R010C10SPC500 Configuration Guide - QoS
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the Configuration of MF classification-based Traffic Policies for IP Packets

Verifying the Configuration of MF classification-based Traffic Policies for IP Packets

After class-based QoS is successfully configured, you can view the traffic classifiers, traffic behaviors, binding between traffic classifiers and behaviors in the specified traffic policy, configured traffic policies and their application, and configured queues and their application.

Procedure

  • Run the display interface [ interface-type [ interface-number ] ] command to view the information about the traffic on the interface.
  • Run the display traffic behavior { system-defined | user-defined } [ behavior-name ] command to view information about the configured traffic behaviors.
  • Run the display traffic classifier { system-defined | user-defined } [ classifier-name ] command to view information about the configured traffic classifiers.
  • Run the display traffic policy { system-defined | user-defined } [ policy-name [ classifier classifier-name ] ] command to view information about the association between all or the specified traffic classifiers and traffic behaviors in traffic policies.
  • Run the display traffic policy statistics interface interface-type interface-number [ .sub-interface ] { inbound | outbound } [ verbose { classifier-based [ class class-name ] | rule-based [ class class-name ] [ filter ] } ] command to view traffic statistics of traffic policies that are configured on the interface.
  • Run the display flow-car statistics { source-ip | destination-ip } [ ip-address ] slot slot-id { inbound | outbound } command to check flow CAR statistics about specific-direction traffic in a specific slot based on the source or destination IP address.
  • Run the display traffic policy_vpn-instance brief command to check the binding relationship between VPN instances and traffic policies.

Example

If the configuration is successful:

  • Running the display traffic behavior command, you can view the name of the configured traffic behavior and its actions.

  • Running the display traffic classifier command, you can view the name of the configured traffic classifier and its matching rules, as well as the logic operator of the rules.

  • Running the display traffic policy command, you can view the association between traffic classifiers and traffic behaviors in a traffic policy.

  • Running the display traffic policy statistics command, you can view the traffic statistics of traffic policies that are configured on the interface.

    <HUAWEI> display traffic policy statistics interface gigabitethernet 1/0/0 inbound
    Info: The statistics is shared because the policy is shared.
    Interface: GigabitEthernet1/0/0 
    Traffic policy inbound: test 
    Traffic policy applied at 2007-08-30 18:30:20 
    Statistics enabled at 2007-08-30 18:30:20
    Statistics last cleared: Never
    Rule number: 7 IPv4, 1 IPv6 
    Current status: OK!
    Item                             Packets                      Bytes
    -------------------------------------------------------------------
    Matched                            1,000                    100,000
      +--Passed                          500                     50,000
      +--Dropped                         500                     50,000
    Missed                               500                     50,000
    
    Last 30 seconds rate
    Item                                 pps                        bps
    -------------------------------------------------------------------
    Matched                            1,000                    100,000
      +--Passed                          500                     50,000
      +--Dropped                         500                     50,000
    Missed                               500                     50,000
    
  • Run the display flow-car statistics command to view flow CAR statistics about specific-direction traffic in a specific slot based on the source or destination IP address. For example:

    [~HUAWEI] display flow-car statistics source-ip 10.1.1.1 slot 2 inbound
    Flow-car IP 10.1.1.1 statistics:
      Passed:                      8291526 packets             12470455104 bytes
      Discard:                  4055366354 packets           6099270996416 bytes
      Passed rate:                       1 pps                       14808 bps
      Discard rate:                      0 pps                           0 bps
  • Run the display traffic policy vpn-instance brief command to view the binding relationship between VPN instances and traffic policies.

    <HUAWEI> display traffic policy vpn-instance brief
    vpn-instance   InboundPolicy         Abnormal-Info
       vpn1           tp-vpn1                    -
       vpn1           tp-vpn2            Hardware resource not enough in slot:1,3
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055024

Views: 22193

Downloads: 115

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next