No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - User Access 01

This is NE40E V800R010C10SPC500 Configuration Guide - User Access
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring the Ethernet Layer 2 Leased Line Access Service

Example for Configuring the Ethernet Layer 2 Leased Line Access Service

This section provides an example for configuring the Ethernet Layer 2 leased line access service, including the networking requirements, configuration roadmap, configuration procedure, and configuration files.

Networking Requirements

The networking is shown in Figure 6-16. The requirements are as follows:

  • The Ethernet Layer 2 leased line users access the Internet by using GE 1/0/2.1 on the router.

  • The user name is layer2lease1@isp1 and the password is Root@123 for the leased line.

  • The VLAN ID for leased line users ranges from 1 to 100.

  • The leased line users obtain IP addresses from the router by using DHCP.

  • RADIUS authentication and RADIUS accounting are used. The IP address of the RADIUS server is 192.168.7.249. The authentication port number is 1645 and the accounting port number is 1646. The RADIUS+1.1 protocol is adopted. The shared key is itellin.

  • The IP address of the DNS server is 192.168.7.252.

  • The network-side interface is GE 1/0/1.

Figure 6-16 Networking for configuring the Ethernet Layer 2 leased line access service

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure authentication and accounting schemes.

  2. Configure a RADIUS server group.

  3. Configure an address pool.

  4. Configure an authentication domain.

  5. Configure access interfaces.

Data Preparation

To complete the configuration, you need the following data:

  • Authentication template name and authentication mode

  • Accounting template name and accounting mode

  • RADIUS server group name, and IP addresses and port numbers of the RADIUS authentication server and accounting server

  • IP address pool name, gateway address, and DNS server address

  • Domain name

  • BAS interface parameters

Procedure

  1. Configure an authentication scheme.

    <HUAWEI> system-view
    [~HUAWEI] aaa
    [~HUAWEI-aaa] authentication-scheme auth1
    [*HUAWEI-aaa-authen-auth1] authentication-mode radius
    [*HUAWEI-aaa-authen-auth1] commit
    [~HUAWEI-aaa-authen-auth1] quit

  2. Configure an accounting scheme.

    [~HUAWEI-aaa] accounting-scheme acct1
    [*HUAWEI-aaa-accounting-acct1] accounting-mode radius
    [*HUAWEI-aaa-accounting-acct1] commit
    [~HUAWEI-aaa-accounting-acct1] quit
    [~HUAWEI-aaa] quit

  3. Configure a RADIUS server group.

    [~HUAWEI] radius-server group rd1
    [*HUAWEI-radius-rd1] radius-server authentication 192.168.7.249 1645
    [*HUAWEI-radius-rd1] radius-server accounting 192.168.7.249 1646
    [*HUAWEI-radius-rd1] radius-server type plus11
    [*HUAWEI-radius-rd1] radius-server shared-key itellin
    [*HUAWEI-radius-rd1] commit
    [~HUAWEI-radius-rd1] quit

  4. Configure an address pool.

    [~HUAWEI] ip pool pool1 bas local
    [*HUAWEI-ip-pool-pool1] gateway 10.82.0.1 255.255.0.0
    [*HUAWEI-ip-pool-pool1] section 0 10.82.0.2 10.82.0.200
    [*HUAWEI-ip-pool-pool1] dns-server 192.168.7.252
    [*HUAWEI-ip-pool-pool1] commit
    [~HUAWEI-ip-pool-pool1] quit

  5. Configure a domain.

    [~HUAWEI] aaa
    [~HUAWEI-aaa] domain isp1
    [*HUAWEI-aaa-domain-isp1] authentication-scheme auth1
    [*HUAWEI-aaa-domain-isp1] accounting-scheme acct1
    [*HUAWEI-aaa-domain-isp1] radius-server group rd1
    [*HUAWEI-aaa-domain-isp1] ip-pool pool1
    [*HUAWEI-aaa-domain-isp1] commit
    [~HUAWEI-aaa-domain-isp1] quit
    [~HUAWEI-aaa]quit

  6. Configure access interfaces.

    If the access interface is an Ethernet sub-interface, you must configure a VLAN. If the access interface is an Ethernet main interface, no VLAN is required.

    You can configure multiple VLANs for an interface used for Layer 2 leased line access.

    [~HUAWEI] license
    [~HUAWEI-license] active bas slot 1
    [*HUAWEI-license] commit
    [~HUAWEI-license]quit
    [~HUAWEI] interface GigabitEthernet 1/0/2.1
    [*HUAWEI-GigabitEthernet1/0/2.1] user-vlan 1 100
    [*HUAWEI-GigabitEthernet1/0/2.1-vlan-1-100] quit
    [*HUAWEI-GigabitEthernet1/0/2.1] bas
    [*HUAWEI-GigabitEthernet1/0/2.1-bas] access-type layer2-leased-line user-name layer2lease1 password simple Root@123 default-domain authentication isp1
    [*HUAWEI-GigabitEthernet1/0/2.1-bas] commit
    [~HUAWEI-GigabitEthernet1/0/2.1-bas] quit
    [~HUAWEI-GigabitEthernet1/0/2.1] quit

Configuration Files

#
 sysname HUAWEI
#
license
active bas slot 1
#
radius-server group rd1
 radius-server authentication 192.168.7.249 1645 weight 0
 radius-server accounting 192.168.7.249 1646 weight 0
 radius-server shared-key itellin
 radius-server type plus11
 radius-server traffic-unit kbyte
#
interface GigabitEthernet1/0/2.1
 user-vlan 1 100
 bas
 access-type layer2-leased-line user-name layer2lease1 password simple Root@123 default-domain authentication isp1
#
interface GigabitEthernet1/0/1
 ip address 192.168.7.1 255.255.255.0
#
ip pool pool1 bas local
 gateway 10.82.0.1 255.255.255.0
 section 0 10.82.0.2 10.82.0.200
 dns-server  192.168.7.252
#
aaa
authentication-scheme  auth1
accounting-scheme  acct1
domain  default0
domain  default1
domain  default_admin
domain  isp1
 authentication-scheme   auth1
 accounting-scheme   acct1
 radius-server group  rd1
 ip-pool   pool1
#
return
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055031

Views: 19302

Downloads: 83

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next