No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - User Access 01

This is NE40E V800R010C10SPC500 Configuration Guide - User Access
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring User Information Backup in Exclusive Address Pool Mode

Configuring User Information Backup in Exclusive Address Pool Mode

In exclusive address pool mode, each RBP is bound to an address pool to control the advertisement and withdrawal of network segment routes of the address pool.

Context

In exclusive address pool mode, an address pool is configured for each interface and bound to an RBP. When an RBP is in the master state, the RBP advertises network segment routes of the address pool to the network side. When an RBP is in the backup state, the RBP withdraws network segment routes of the address pool. In this way, the RBP controls the advertisement and withdrawal of network-side routes to ensure that network-to-user traffic is always forwarded on the master device. The forwarding paths of network-to-user traffic are therefore controlled based on interfaces.

Perform the following steps on an RBP backup group.

Procedure

  • RADIUS-authorized address pool scenarios:
    1. Run system-view

      The system view is displayed.

    2. Run ipv6 pool pool-name bas local

      A local IPv6 address pool is created and the IPv6 address pool view is displayed.

    3. Run prefix

      The IPv6 prefix pool view is displayed and prefixes are configured in the IPv6 prefix pool.

    4. Run quit

      Exit the IPv6 prefix pool view.

    5. Run quit

      Exit the IPv6 address pool view.

    6. Run remote-backup-profile profile-name

      The remote backup profile view is displayed.

    7. Run ipv6-pool source-pool-name include destination-pool-name [ node node-id ]

      A source IPv6 address pool is mapped to a destination address pool.

    8. Run ipv6-pool destination-pool-name

      An IPv6 address pool is configured.

      The name of the IPv6 address pool is specified by destination-pool-name in the preceding step.

    9. Run commit

      The configuration is committed.

  • Locally-authorized address pool scenarios:

    • Divide domains based on links and bind each domain to an address pool:

    1. Run system-view

      The system view is displayed.

    2. Run ipv6 pool pool-name bas local

      A local IPv6 address pool is created.

    3. Run prefix

      Prefixes are configured in the IPv6 prefix pool.

    4. Run aaa

      The AAA view is displayed.

    5. Run domain

      The AAA domain view is displayed.

    6. Run ipv6-pool pool-name

      The IPv6 address pool is bound to a domain.

    7. Run quit

      Exit the AAA domain view.

    8. Run quit

      Exit the AAA view.

    9. Run remote-backup-profile profile-name

      The remote backup profile view is displayed.

    10. Run ipv6-pool pool-name

      An IPv6 address pool is configured.

    11. Run commit

      The configuration is committed.

    • Map a source IPv6 address pool to a destination address pool:

    1. Run system-view

      The system view is displayed.

    2. Run ipv6 pool pool-name bas local

      A local IPv6 address pool is created.

    3. Run aaa

      The AAA view is displayed.

    4. Run domain

      The AAA domain view is displayed.

    5. Run ipv6-pool pool-name

      The IPv6 address pool is bound to a domain.

    6. Run quit

      Exit the AAA domain view.

    7. Run quit

      Exit the AAA view.

    8. Run ipv6 pool pool-name bas local

      A local IPv6 address pool is created.

    9. Run prefix

      Prefixes are configured in the IPv6 prefix pool.

    10. Run quit

      Exit the IPv6 address pool view.

    11. Run remote-backup-profile profile-name

      The remote backup profile view is displayed.

    12. Run ipv6-pool source-pool-name include destination-pool-name [ node node-id ]

      A source IPv6 address pool is mapped to a destination address pool.

    13. Run ipv6-pool destination-pool-name

      An IPv6 address pool is configured.

      The name of the IPv6 address pool is specified by destination-pool-name in the preceding step.

    14. Run commit

      The configuration is committed.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055031

Views: 17348

Downloads: 70

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next