No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S V800R010C10SPC500 Configuration Guide - MPLS 01

This is NE20E-S V800R010C10SPC500 Configuration Guide - MPLS
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Conditions That Trigger LDP Resource Threshold-Reaching Alarms

Configuring Conditions That Trigger LDP Resource Threshold-Reaching Alarms

Conditions that trigger LDP resource threshold-reaching alarms can be configured. If the number of remote LDP adjacencies or the number of outsegment entries reaches a specified upper alarm threshold, the device can report an alarm to an NMS.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run mpls

    The MPLS view is displayed.

  3. Run one or more of the following commands:
    • Run mpls remote-adjacency-number threshold-alarm upper-limit upper-limit-value lower-limit lower-limit-valueConditions that trigger the threshold-reaching alarm and its clear alarm for remote LDP adjacencies are configured.

    • Run mpls outsegment-number threshold-alarm upper-limit upper-limit-value lower-limit lower-limit-valueConditions that trigger the threshold-reaching alarm and its clear alarm for outsegment entries are configured.

    • Run mpls mldp-tree-number threshold-alarm upper-limit upper-limit-value lower-limit lower-limit-valueThe upper and lower alarm thresholds for the number of mLDP LSPs are set.

    • Run mpls mldp-branch-number threshold-alarm upper-limit upper-limit-value lower-limit lower-limit-valueThe upper and lower alarm thresholds for the number of mLDP sub-LSPs are set.

    Configure the following parameters in the preceding command:

    • upper-limit-value: specifies the upper alarm threshold of the proportion of used LDP resources to all LDP resources supported by a device.
    • lower-limit-value: specifies the lower alarm threshold for the proportion of used LDP resources to all LDP resources supported by a device.
    • upper-limit-value must be greater than lower-limit-value.

    By default, the upper threshold for alarms is 80% and the lower threshold for clear alarms is 75%.

    NOTE:
    • Each command only configures the trigger conditions for an alarm and its clear alarm. Although trigger conditions are met, the alarm and its clear alarm can be generated only after the snmp-agent trap enable feature-name mpls_lspm trap-name { hwmplsresourcethresholdexceed | hwmplsresourcethresholdexceedclear } command is run to enable the device to generate an LDP resource insufficiency alarm and its clear alarm.

    • After the snmp-agent trap enable feature-name mpls_lspm trap-name { hwmplsresourcetotalcountexceed | hwmplsresourcetotalcountexceedclear } command is run to enable the device to generate an LDP resource insufficiency alarm and its clear alarm, note the following issues:

      • If the number of used LDP resources reaches the maximum number of LDP resources supported by a device, a maximum number-reaching alarm is generated.

      • If the number of used LDP resources falls to 95% or below of the maximum number of LDP resources supported by a device, a clear alarm is generated.

  4. Run commit

    The configuration is committed.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055103

Views: 19372

Downloads: 35

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next