No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S V800R010C10SPC500 Configuration Guide - MPLS 01

This is NE20E-S V800R010C10SPC500 Configuration Guide - MPLS
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting BFD Parameters on the Egress

Setting BFD Parameters on the Egress

This section describes how to set BFD parameters on the egress to monitor CR-LSPs using BFD sessions.

Procedure

  1. Run system-view

    The system view is displayed.

  2. The IP link, LSP, or TE tunnel can be used as the reverse tunnel to inform the ingress of a fault. If there is a reverse LSP or a TE tunnel, use the reverse LSP or the TE tunnel. If no LSP or TE tunnel is established, use an IP link as a reverse tunnel. If the configured reverse tunnel requires BFD detection, you can configure a pair of BFD sessions for it. Run the following commands as required:

    • Configure a BFD session to monitor reverse channels.

      • For an LDP LSP, run bfd session-name bind ldp-lsp peer-ip ip-address nexthop ip-address [ interface interface-type interface-number ]

      • For a CR-LSP, run bfd session-name bind mpls-te interface tunnel interface-number te-lsp [ backup ]

      • For a TE tunnel, run bfd session-name bind mpls-te interface tunnel interface-number

      For an IP link, run bfd session-name bind peer-ip ip-address [ vpn-instance vpn-name ] [ source-ip ip-address ]

  3. Run discriminator local discr-value

    The local discriminator of the BFD session is set.

    NOTE:

    A BFD session group does not need to be configured with a local discriminator. Each sub-session in a BFD session group has its own discriminator.

  4. Run discriminator remote discr-value

    The remote discriminator of the BFD session is set.

    NOTE:

    The local discriminator of the local device and the remote discriminator of the remote device are the same. The remote discriminator of the local device and the local discriminator of the remote device are the same. A discriminator inconsistency causes the BFD session to fail to be established.

  5. (Optional) Run min-tx-interval interval

    The local minimum interval at which BFD packets are sent is configured.

    If an IP link is used as a reverse tunnel, this parameter is inapplicable.

    • Effective local interval at which BFD packets are sent = MAX { Configured local interval at which BFD packets are sent, Configured remote interval at which BFD packets are received }
    • Effective local interval at which BFD packets are received = MAX { Configured remote interval at which BFD packets are sent, Configured local interval at which BFD packets are received }
    • Effective local detection interval = Effective local interval at which BFD packets are received x Configured remote detection multiplier

    For example:

    • The local interval at which BFD packets are sent is set to 200 ms, the local interval at which BFD packets are received is set to 300 ms, and the local detection multiplier is set to 4.

    • The remote interval at which BFD packets are sent is set to 100 ms, the remote interval at which BFD packets are received is set to 600 ms, and the remote detection multiplier is set to 5.

    Then,

    • Effective local interval at which BFD packets are sent = MAX { 200 ms, 600 ms } = 600 ms; effective local interval at which BFD packets are received = MAX { 100 ms, 300 ms } = 300 ms; effective local detection period = 300 ms x 5 = 1500 ms

    • Effective remote interval at which BFD packets are sent = MAX { 100 ms, 300 ms } = 300 ms; effective remote receiving interval = MAX { 200 ms, 600 ms } = 600 ms; effective remote detection period = 600 ms x 4 = 2400 ms

  6. (Optional) Run min-rx-interval interval

    The local minimum interval at which BFD packets are received is configured.

  7. (Optional) Run detect-multiplier multiplier

    The BFD detection multiplier is configured.

  8. Run commit

    The configurations are committed.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055103

Views: 20077

Downloads: 35

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next