No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S V800R010C10SPC500 Configuration Guide - MPLS 01

This is NE20E-S V800R010C10SPC500 Configuration Guide - MPLS
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the Configuration of Establishment of MPLS TE Tunnel

Verifying the Configuration of Establishment of MPLS TE Tunnel

After adjusting the establishment of the MPLS TE tunnel, you can view information about the tunnel interface.

Prerequisites

The establishment of the MPLS TE tunnel has been adjusted.

Procedure

  • Run the display mpls te tunnel-interface command to check information about a tunnel interface on the ingress of a tunnel.

Example

Run the following command to check the previous configurations.

Run the display mpls te tunnel-interface command to view information about the tunnel interface.

<HUAWEI> display mpls te tunnel-interface
    Tunnel Name       : Tunnel1
    Signalled Tunnel Name: -
    Tunnel State Desc : CR-LSP is Up
    Tunnel Attributes   :     
    Active LSP          : Primary LSP                                       
    Traffic Switch      : - 
    Session ID          : 1
    Ingress LSR ID      : 1.1.1.9               Egress LSR ID: 4.4.4.9
    Admin State         : UP                    Oper State   : UP
    Signaling Protocol  : RSVP
    FTid                : 1
    Tie-Breaking Policy : None                  Metric Type  : None
    Bfd Cap             : None                  
    Reopt               : Disabled              Reopt Freq   : -              
    Inter-area Reopt    : Disabled 
    Auto BW             : Disabled              Threshold    : 0 percent
    Current Collected BW: 0 kbps                Auto BW Freq : 0
    Min BW              : 0 kbps                Max BW       : 0 kbps
    Offload             : Disabled              Offload Freq : - 
    Low Value           : -                     High Value   : - 
    Readjust Value      : - 
    Offload Explicit Path Name: 
    Tunnel Group        : -                                              
    Interfaces Protected: -
    Excluded IP Address : -
    Referred LSP Count  : 0  
    Primary Tunnel      : -                     Pri Tunn Sum : -              
    Backup Tunnel       : -                                                    
    Group Status        : -                     Oam Status   : -             
    IPTN InLabel        : -                     Tunnel BFD Status : -                               
    BackUp LSP Type     : None                  BestEffort   : Disabled
    Secondary HopLimit  : -
    BestEffort HopLimit  : -
    Secondary Explicit Path Name: -
    Secondary Affinity Prop/Mask: 0x0/0x0
    BestEffort Affinity Prop/Mask: 0x0/0x0  
    IsConfigLspConstraint: -
    Hot-Standby Revertive Mode:  Revertive
    Hot-Standby Overlap-path:  Disabled
    Hot-Standby Switch State:  CLEAR
    Bit Error Detection:  Disabled
    Bit Error Detection Switch Threshold:  -
    Bit Error Detection Resume Threshold:  -
    Ip-Prefix Name    : -
    P2p-Template Name : -
    PCE Delegate      : Only status report      LSP Control Status : Local control
    Entropy Label       :None 
    Associated Tunnel Group ID: -                 Associated Tunnel Group Type: -
    Auto BW Remain Time : 200 s   Reopt Remain Time  : 100 s

    Primary LSP ID      : 1.1.1.9:19
    LSP State           : UP                    LSP Type     : Primary
    Setup Priority      : 7                     Hold Priority: 7
    IncludeAll          : 0x0
    IncludeAny          : 0x0
    ExcludeAny          : 0x0
    Affinity Prop/Mask  : 0x0/0x0               Resv Style   :  SE
    Configured Bandwidth Information:
    CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
    CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
    CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
    CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
    Actual Bandwidth Information:
    CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
    CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
    CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
    CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
    Explicit Path Name  : -                                Hop Limit: -
    Record Route        : Disabled              Record Label : Disabled
    Route Pinning       : Disabled
    FRR Flag            : Disabled
    IdleTime Remain     : -
    BFD Status          : -
    Soft Preemption     : Enabled 
    Reroute Flag        : Disabled
    Pce Flag            : Normal
    Path Setup Type     : EXPLICIT
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055103

Views: 22008

Downloads: 37

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next