No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S V800R010C10SPC500 Configuration Guide - MPLS 01

This is NE20E-S V800R010C10SPC500 Configuration Guide - MPLS
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the LDP over TE Configuration

Verifying the LDP over TE Configuration

After configuring LDP over TE, you can view information about an LDP LSP on the ingress.

Prerequisites

LDP over TE has been configured.

Procedure

  • Run the display mpls ldp lsp [ destination-address mask-length ] command to check information about the LDP LSP on the ingress node.

Example

After the configurations, run the preceding command to view the following results:

Run the display mpls ldp lsp command on the ingress to view the outbound interface of the TE tunnel.

<HUAWEI> display mpls ldp lsp
 LDP LSP Information
 -------------------------------------------------------------------------------
 DestAddress/Mask   In/OutLabel    UpstreamPeer    NextHop          OutInterface
 -------------------------------------------------------------------------------
*1.1.1.1/32         Liberal/25                     DS/2.2.2.2
 1.1.1.1/32         3/NULL         2.2.2.2         127.0.0.1         Loop1
 2.2.2.2/32         NULL/3         -               10.1.1.2          GE0/3/1
 2.2.2.2/32         16/3           2.2.2.2         10.1.1.2          Tunnel1
 3.2.1.0/24         NULL/3         -               10.1.1.2          GE0/3/1
 3.2.1.0/24         17/3           2.2.2.2         10.1.1.2          GE0/3/1
 3.3.1.0/24         NULL/3         -               10.1.1.2          GE0/3/1
 3.3.1.0/24         18/3           2.2.2.2         10.1.1.2          GE0/3/1
*10.1.1.0/24        Liberal/3                      DS/2.2.2.2
 10.1.1.0/24        3/NULL         2.2.2.2         10.1.1.1          GE0/3/1
 10.2.1.0/24        NULL/3         -               10.1.1.2          GE0/3/1
 10.2.1.0/24        19/3           2.2.2.2         10.1.1.2          GE0/3/1
*10.5.1.0/24        Liberal/26                     DS/2.2.2.2
 10.5.1.0/24        3/NULL         2.2.2.2         10.5.1.1          GE0/3/0
 10.6.1.0/24        3/NULL         2.2.2.2         10.6.1.1          GE0/3/2
 -------------------------------------------------------------------------------
 TOTAL: 12 Normal LSP(s) Found.
 TOTAL: 3 Liberal LSP(s) Found.
 TOTAL: 0 Frr LSP(s) Found.
An asterisk (*) before an LSP means the LSP is not established
 An asterisk (*) before a Label means the USCB or DSCB is stale
 An asterisk (*) before an UpstreamPeer means the session is stale
 An asterisk (*) before a DS means the session is stale
 An asterisk (*) before a NextHop means the LSP is FRR LSP
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055103

Views: 19774

Downloads: 35

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next