Example for Collecting Statistics About MPLS Original Flows
This section provides an example for configuring NetStream to collect statistics about MPLS original flows. Statistics about MPLS original flows with a specified label can be collected.
Networking Requirements
In Figure 3-19, Device A, Device B, and Device C support MPLS and use OSPF as an IGP protocol on the MPLS backbone network.
Local LDP sessions between Device A and Device B, and between Device B and Device C are established. A remote Label Distribution Protocol (LDP) session between Device A and Device C is established. NetStream is enabled on Device B to collect statistics about MPLS flows.
Configuration Roadmap
The configuration roadmap is as follows:
Configure the LDP session between every two Devices.
Specify the remote peer and its IP address on the two Devices that have established a remote LDP session.
Specify the destination IP address, destination port number, and source IP address of NetStream flows to be output.
Data Preparation
To complete the configuration, you need the following data:
IP addresses of interfaces on each router as shown in Figure 3-19, OSPF process 1, and area 0
router A's remote peer with name router C and IP address 3.3.3.9.
router C's remote peer with name router A and IP address 1.1.1.9.
Number of the slot in which the NetStream service processing board resides (In this example, the NetStream service processing board is in slot 1.)
Procedure
- Assign an IP address to each interface.
# Assign an IP address and a mask to each interface (including loopback interfaces) according to Figure 3-19. For configuration details, see Configuration Files in this section.
- Configure the LDP session between every two Devices.
# Configure OSPF to advertise host routes to the specified Label Switching Router (LSR) ID and of the network segments to which interfaces on the router are connected. Enable basic MPLS functions on each router and its interfaces.
For configurations of the static MPLS TE tunnel, see the chapter "Basic MPLS Configurations" in HUAWEI NE20E-S NE20E Configuration Guide - MPLS.
- Enable NetStream on GigabitEthernet 0/1/0 of Device B.
# Configure the NetStream service processing mode on an interface board.
[*DeviceB] slot 1 [*DeviceB-slot-1] ip netstream sampler to slot self [*DeviceB-slot-1] return
# Configure NetStream to collect statistics about incoming and outgoing packets on GigabitEthernet 0/1/0 of Device B.
[*DeviceB] interface GigabitEthernet 0/1/0 [*DeviceB-GigabitEthernet0/1/0] ip netstream inbound [*DeviceB-GigabitEthernet0/1/0] ip netstream outbound [*DeviceB-GigabitEthernet0/1/0] quit
# Configure NetStream to sample both inner IP packets and labels of MPLS packets.
[*DeviceB] ip netstream mpls-aware label-and-ip
# Specify the destination address, destination port number, and source address for NetStream flows output in V5 format.
[*DeviceB] ip netstream export host 192.168.1.2 2100 [*DeviceB] ip netstream export source 10.1.2.1
# Enable NetStream sampling and configure the fixed packet sampling mode.
[*DeviceB] ip netstream sampler fix-packets 10000 inbound [*DeviceB] ip netstream sampler fix-packets 10000 outbound [*DeviceB] commit
- Verify the configuration.
# Run the display ip netstream cache origin slot 1 command in the user view. You can view information about the NetStream flow buffer and statistics about output flows.
<HUAWEI> display ip netstream cache origin slot 1 DstIf SrcIf DstP Msk Pro Tos SrcP Msk Flags Ttl Packets Bytes NextHop Direction DstIP DstAs SrcIP SrcAs BGP: BGP NextHop TopLabelType Label1 Exp1 Bottom1 Label2 Exp2 Bottom2 Label3 Exp3 Bottom3 TopLabelIpAddress VlanId VniId -------------------------------------------------------------------------- Unknown GigabitEthernet0/1/0 0 0 253 0 0 0 0 60 3 384 0.0.0.0 in 192.172.133.151 0 192.172.131.151 0 0.0.0.0 UNKNOWN 0 0 0 0 0 0 0 0 0 0.0.0.0 0 0 Unknown GigabitEthernet0/1/1 0 0 253 0 0 0 0 60 1 128 0.0.0.0 in 192.173.81.232 0 192.173.79.232 0 0.0.0.0 UNKNOWN 0 0 0 0 0 0 0 0 0 0.0.0.0 0 0
Configuration Files
Device A configuration file
# sysname DeviceA # mpls lsr-id 1.1.1.9 # mpls lsp-trigger all # mpls ldp # mpls ldp remote-peer Devicec remote-ip 3.3.3.9 # interface GigabitEthernet0/1/0 undo shutdown ip address 10.1.1.1 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 1.1.1.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 10.1.1.0 0.0.0.255 network 1.1.1.9 0.0.0.0 # return
Device B configuration file
# slot 1 ip netstream sampler to slot self # sysname DeviceB # ip netstream sampler fix-packets 10000 inbound ip netstream sampler fix-packets 10000 outbound ip netstream export source 10.1.2.1 ip netstream export host 192.168.1.2 2100 # mpls lsr-id 2.2.2.9 # mpls lsp-trigger all # mpls ldp # interface GigabitEthernet0/1/0 undo shutdown ip address 10.1.1.2 255.255.255.0 ip netstream inbound ip netstream outbound mpls mpls ldp # interface GigabitEthernet0/2/0 undo shutdown ip address 10.1.2.1 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 2.2.2.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 10.1.1.0 0.0.0.255 network 10.1.2.0 0.0.0.255 network 2.2.2.9 0.0.0.0 # return
Device C configuration file
# sysname DeviceC # ip netstream mpls-aware label-and-ip # mpls lsr-id 3.3.3.9 # mpls lsp-trigger all # mpls ldp # mpls ldp remote-peer Devicea remote-ip 1.1.1.9 # interface GigabitEthernet0/1/0 undo shutdown ip address 10.1.2.2 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 3.3.3.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 4.1.1.0 0.0.0.255 network 3.3.3.9 0.0.0.0 # return
