No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S V800R010C10SPC500 Feature Description - IP Multicast 01

This is NE20E-S V800R010C10SPC500 Feature Description - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Switch-MDT Switchover

Switch-MDT Switchover

Background

According to the process of establishing a Share-multicast distribution tree (Share-MDT) described in the previous section, you can find that the VPN instance bound to PE3 has no receivers but PE3 still receives the VPN multicast data packet of the group (192.1.1.1, 225.1.1.1). This is a defect of the multicast domain (MD) scheme: All the PEs belonging to the same MD can receive multicast data packets regardless of whether they have receivers. This wastes the bandwidth and imposes extra burden on PEs.

In MVPN, an optimized solution, Switch-MDT, is provided so that multicast data can be transmitted on demand. It allows on-demand multicast transmission. Traffic will be switched from the Share-MDT to the Switch-MDT if multicast traffic on PEs reaches the maximum. Only the PEs that have receivers connected to them will receive multicast data from the Switch-MDT. This reduces the stress on PEs and bandwidth consumption.

Implementation

Figure 7-10 shows the switch-MDT implementation process based on the assumption that a share-MDT has been successfully established.

Figure 7-10 Switch-MDT implementation

  1. On PE 1, set 238.1.1.0-238.1.1.255 as the switch-group-pool address range of the switch-MDT and set the data forwarding rate threshold that triggers a switch-MDT switchover.

  2. When the rate of data forwarded by the source connected with CE 1 exceeds the configured threshold, PE 1 selects a group address (for example, 238.1.1.0) and periodically sends signaling packets to other PEs through the share-MDT to instruct them to switch to the switch-MDT.

  3. If PE 2 has a receiver, after receiving the signaling packet, PE 2 joins the group 238.1.1.0. Then, a switch-MDT is set up. The switch-MDT setup process is similar to that of a share-MDT. If PE 3 has no receivers, after receiving the signaling packet, PE 3 does not join the switch-MDT. As a result, only PE 2 can receive the VPN multicast data packet from the group (192.1.1.1, 225.1.1.1). Note that PIM control packets are still transmitted along the share-MDT.

    A switch-MDT switchover occurs if any of the following conditions are met:

    • The source and group addresses of VPN multicast data packets match the source and group address ranges defined in ACL filtering rules. Otherwise, the packets are still forwarded along the share-MDT.

    • The forwarding rate of VPN multicast data packets exceeds the switchover threshold for a specified time range.

  4. In some cases, the forwarding rate of VPN multicast data packets fluctuates around the switchover threshold. To prevent multicast data packets from being frequently switched between a share-MDT and a switch-MDT, the system does not immediately perform a switchover after the system detects that the forwarding rate exceeds the switchover threshold. Instead, the system starts a switch-delay timer. During the switch-MDT setup, the share-MDT is still used for multicast data packet forwarding. Therefore, the switch-delay timer helps implement non-stop data forwarding during a switchover from a share-MDT to a switch-MDT. Before the switch-delay timer times out, the system continues to detect the data forwarding rate. If the rate remains consistently higher than the switchover threshold throughout the timer period, data packets are switched to the switch-MDT. Otherwise, the packets are still forwarded along the share-MDT.

Switchback from the Switch-MDT to Share-MDT

A PE switches data back from a switch-MDT to a share-MDT if any of the conditions are met:

  • The forwarding rate of VPN multicast data packets is lower than the specified threshold and does not exceed this threshold during the switch-Holddown period.

  • In some cases, the forwarding rate of VPN multicast data packets fluctuates around the switchover threshold. To prevent the multicast data flow from being frequently switched between a switch-MDT and a share-MDT, the system does not immediately perform a switchover when the system detects that the forwarding rate is lower than the switchover threshold. Instead, the system starts a Holddown timer. Before the Holddown timer expires, the system continues to detect the data forwarding rate. If the rate remains consistently lower than the switchover threshold throughout the timer period, the data packets are switched back to the share-MDT. Otherwise, the packets are still forwarded along the switch-MDT.

  • After the switch-group-pool is switched, the switch-group address encapsulated in VPN multicast data is not in the address range of the new switch-group-pool.

  • After advanced ACL rules that control a switch-MDT switchover change, VPN multicast data packets do not comply with the new ACL rules.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055119

Views: 12615

Downloads: 19

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next