No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S2 V800R010C10SPC500 Configuration Guide - LAN Access and MAN Access 01

This is NE20E-S2 V800R010C10SPC500 Configuration Guide - LAN Access and MAN Access
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Setting GARP Timers

(Optional) Setting GARP Timers

Context

When a GARP device starts, its LeaveAll timer starts. When the LeaveAll timer expires, the device sends a LeaveAll message to request other GARP devices to re-register all of its attributes. It then restarts its LeaveAll timer for a new round of polling.

Devices on a network may have different settings for the LeaveAll timer, but only the LeaveAll timer with the smallest value takes effect. When the LeaveAll timer with the smallest value expires, that device whose LeaveAll timer value is the smallest sends a LeaveAll message to all other devices and restarts its own LeaveAll timer. After receiving the LeaveAll message, the other devices restart all of their GARP timers, including the LeaveAll timer. They then propagate the LeaveAll messages to all other connected devices except for the device from whom they initially received the LeaveAll message.

When setting GARP timers for an interface, note the following:
  • The undo garp timer command restores the default values of GARP timers. If the default value of a timer is out of the valid range, the undo garp timer command does not take effect.

  • The value range of each timer changes with the values of the other timers. If a timer value that you wish to set falls outside of the allowed range, you can change the value of another timer that relates to the value range of this timer.

  • To restore the default values of all GARP timers, restore in sequence the Hold timer, Join timer, Leave timer, and LeaveAll timer to default values.

When many dynamic VLANs need to be registered or the network radius is large, using the default values of GARP timers may cause VLAN flapping and high CPU usage. To prevent such problems, increase timer values. The following values are recommended depending on the number of VLANs.
Table 5-1 Relationship between GARP timer values and number of dynamic VLANs to be registered

Timer

Number of Dynamic VLANs to Be Registered (N)

N <= 500

500 < N <= 1000

1000 < N <= 1500

N > 1500

GARP Hold timer

100 centiseconds (1s)

200 centiseconds (2s)

800 centiseconds (8s)

1000 centiseconds (10s)

GARP Join timer

600 centiseconds (6s)

1200 centiseconds (12s)

4000 centiseconds (40s)

6000 centiseconds (1 min)

GARP Leave timer

3000 centiseconds (30s)

6000 centiseconds (1 min)

20000 centiseconds (3 min and 20s)

30000 centiseconds (5 min)

GARP LeaveAll timer

12000 centiseconds (2 min)

24000 centiseconds (4 min)

30000 centiseconds (5 min)

32765 centiseconds (5 min and 27.65s)

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run garp timer leaveall timer-value

    The value of a LeaveAll timer is set.

    The default value of a LeaveAll timer is 1000 centiseconds (10s).

    The Leave timer value of each interface is restricted by the global LeaveAll timer value. When setting a value for the global LeaveAll timer, ensure that all the interfaces configured with a GARP Leave timer are working properly.

  3. Run interface interface-type interface-number

    The interface view is displayed.

  4. Run garp timer { hold | join | leave } timer-value

    The value of the Hold timer, Join timer, or Leave timer is set for the interface.

    By default, the values of the Hold timer, Join timer, and Leave timer are 10 centiseconds, 20 centiseconds, and 60 centiseconds, respectively.

  5. Run commit

    The configuration is committed.

Translation
Download
Updated: 2019-01-02

Document ID: EDOC1100055378

Views: 16859

Downloads: 35

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next