No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE20E-S2 V800R010C10SPC500 Configuration Guide - System Management 01

This is NE20E-S2 V800R010C10SPC500 Configuration Guide - System Management
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Performing In-Service Patch Installation

Example for Performing In-Service Patch Installation

This section provides an example for installing patches without interrupting services.

Networking Requirements

In-service patch installation can be performed on a device if the device performance needs to be optimized without affecting the use of the current system software, and if the device must work uninterruptedly for a long time.

As shown in Figure 22-5, the performance of Device A needs to be optimized. Huawei has provided a patch file for the customer to install.

Figure 22-5 Networking diagram for performing in-service patch installation

Precautions

  • Patch versions on the AMB and SMB must be the same.

Configuration Roadmap

The configuration roadmap is as follows:

  1. Upload a patch to the storage medium of AMB.
  2. Load and run the patch.
  3. Verify the configuration.

Data Preparation

To complete the configuration, you need the following data:

  • Name of the patch, which is V800R010C10SPH001.pat in this example
  • Path used to save the patch, which is cfcard:/ in this example

Procedure

  1. Upload the patch matching the system software.

    # Configure Device A as an FTP server.
    <HUAWEI> system-view
    [~HUAWEI] sysname DeviceA
    [*HUAWEI] commit
    [~DeviceA] ftp server enable
    Info:  Enabling the FTP server configuration  succeeded. 
    [*DeviceA] aaa
    [*DeviceA-aaa] local-user user1 password cipher Hello-huawei123
    [*DeviceA-aaa] local-user user1 service-type ftp
    [*DeviceA-aaa] local-user user1 ftp-directory cfcard:/
    [*DeviceA-aaa] commit
    [~DeviceA-aaa] quit
    [~DeviceA] quit
    After the configuration is complete, run the display local-user command to view user information.
    <DeviceA> display local-user
    --------------------------------------------------------------------------------
    ----------------                                                                
    Username                         State   Type   Access-limit   Online   AdminLevel   UsergroupId                                                                
    ------------------------------------------------------------------------------------------------                                                                
    user1                            Active  F                No        0   -            -                                                                          
    ------------------------------------------------------------------------------------------------                                                                
    Total 1, 1 printed   
    # On the PC, configure the binary transmission mode and set c:\temp as the working directory.
    NOTE:

    The following part uses the Windows XP system as an example.

    1. Save the uploaded system software to the specified directory (for example, c:\temp).
    2. Choose Start > Run. Enter cmd, and then press Enter
    3. Enter FTP 10.1.1.1. In the user field, enter the user name; in the password field, enter the password.
    The following configurations are displayed:
    ftp 10.1.1.1
    Connect to 10.1.1.1.
    220 FTP server ready.
    User <10.1.1.1:<none>>:user1
    331 Please specify the password.
    Password:
    230 User logged in.
    
    Specify a directory for the FTP client to store the uploaded files and specify the file transfer mode.
    ftp> binary
    200 Type set to I.
    ftp> lcd c:\temp
    Local directory now c:\temp.
    # Upload the patch matching the current system software from the PC to Device A.
    ftp> put V800R010C10SPH001.pat
    200 Port command okay.
    226 Transfer complete.

    # Copy the patch to the storage medium of the SMB.

    <DeviceA> copy cfcard:/V800R010C10SPH001.pat slave#cfcard:/
    Copy cfcard:/V800R010C10SPH001.pat to slave#cfcard:/?[Y/N]:Y
    Info:Copied file cfcard:/V800R010C10SPH001.pat to slave#cfcard:/...Done

  2. Load and run the patch.

    <DeviceA> patch load V800R010C10SPH001.pat all run
    Info: Operating, please wait for a moment......done.
    Info: Succeeded in running the patch.

  3. Verify the configuration.

    After the preceding configurations, run the display patch-information command, and you can view patches in the running state.

    <DeviceA> display patch-information
    Patch Package Name    :cfcard:/V800R010C10SPH001.PAT
    Patch Package Version :V800R010C10SPH001
    Patch Package State   :Running   
    Patch Package Run Time:2011-11-07 11:55:01

Configuration Files

None

Translation
Download
Updated: 2019-01-02

Document ID: EDOC1100055400

Views: 14515

Downloads: 26

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next