Enable SNMP
|
Specifies whether the videoconferencing network management
system uses SNMP to manage your endpoint.
NOTE: If you
set this parameter to Enable, you must set
other SNMP parameters.
|
The default value is Enable.
|
SNMPv2
|
Specifies whether to use SNMPv2. If you set this parameter
to Enable, you must set Get community name, Set community name, and Trap community name.
|
The default value is Disable.
Using SNMPv2
may impose security risks. Please set this parameter with caution.
|
Get community name
|
Specifies the credential that the videoconferencing network
management server uses to obtain endpoint settings.
|
This parameter contains 8 to 32 characters. In addition, it must
include at least two of the following: uppercase letter, lowercase
letter, digit, or special character.
|
Set community name
|
Specifies the credential that the videoconferencing network
management server uses to specify endpoint settings.
|
This parameter contains 8 to 32 characters. In addition, it must
include at least two of the following: uppercase letter, lowercase
letter, digit, or special character.
|
Trap community name
|
Specifies the credential that the endpoint uses to report alarms
to the videoconferencing network management server.
|
This parameter contains 8 to 32 characters. In addition, it must
include at least two of the following: uppercase letter, lowercase
letter, digit, or special character.
|
Trap server address 1
Trap server address 2
Trap server address 3
|
Specify the IP address to which your endpoint sends traps, namely,
the IP address of the computer where the videoconferencing network
management system server is installed.
NOTE: A trap is an unrequested
message that a managed device (for example, an endpoint) sends to a trap server
(for example, the SMC2.0) to report urgent and important events.
|
No default value is set for this parameter.
You can
leave this parameter blank.
|
Trap server port 1
Trap
server port 2
Trap server port 3
|
Specify the port number to which your endpoint sends traps, namely,
the port number of the computer where the videoconferencing network
management system server is installed. |
The default value is 162.
Value range: 1-65534
|
Trap version
|
Specifies the version of the traps that the endpoint sends to the videoconferencing
network management system through SNMP.
|
The default value is v3 trap.
|
Trap timeout time
|
Specifies the timeout interval for traps, in seconds.
This parameter is available only when Trap version is
set to v2 inform or v3 inform.
|
The default value is 1.
|
Trap retry times
|
Specifies the number of retry attempts for sending a trap.
This parameter is available only when Trap version is
set to v2 inform or v3 inform.
|
The default value is 5.
|
User name
|
Specifies the user name for sending traps.
This parameter is available only when Trap version is
set to v3 trap or v3 inform.
|
The default value is trapinit.
|
Engine ID
|
Specifies the ID for sending trap packets.
This parameter
is available only when Trap version is
set to v3 trap or v3 inform.
|
No default value is set for this parameter.
You can
leave this parameter blank.
The ID must be a string consisting
of an even number of characters ranging from 12 to 64 digits and must
start with 800007DB04 followed by a hexadecimal number (consisting
of 0-9, a, b, c, d, e, f, A, B, C, D, E, and F).
|
Authentication protocol
Authentication password
|
Specify the authentication mode and password that your endpoint uses to send traps
to the videoconferencing network management system through SNMP.
This parameter is available only when Trap version is
set to v3 trap or v3 inform.
|
The default value of Authentication
protocol is SHA.
Set Authentication password to the password
defined on the videoconferencing network management system.
If the two passwords are different, authentication fails.
|
Encryption protocol
Encryption password
|
Specify the encryption protocol and password that your endpoint uses to send traps
to the videoconferencing network management system through SNMP.
If you select No encryption for Encryption protocol, traps are transmitted using plaintext.
This parameter is available only when Trap version is
set to v3 trap or v3 inform.
|
The default value of Encryption
protocol is AES.
Set Encryption password to a string
of 48 characters or less, consisting of letters, digits, and special
characters.
|
SNMPv3 Authentication Information
|
User name
|
Specifies the user name for connecting your endpoint to the videoconferencing
network management system through SNMPv3.
|
The default value is v3user.
|
User rights
|
Specifies the user permissions of your endpoint when it connects to
the videoconferencing network management system.
- Read
and write: read and write
- Read
only: read-only
|
The default value is Read
and write.
|
Authentication protocol
Authentication password
|
Specify the authentication mode and password for connecting
the videoconferencing network management system to your endpoint.
|
The default value of Authentication
protocol is SHA.
When the videoconferencing network management
system attempts to connect to your endpoint, Authentication
protocol and Authentication password set on your endpoint are required.
|
Encryption protocol
Encryption password
|
Specify the encryption protocol and password for connecting
the videoconferencing network management system to your endpoint.
|
The default value of Encryption
protocol is AES.
Set Encryption password to a string
of 8 to 48 characters, consisting of letters, digits, and special
characters.
|
