No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E-M2 V800R010C10SPC500 Configuration Guide - System Management 01

This is NE40E-M2 V800R010C10SPC500 Configuration Guide - System Management
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Outputting Information to an SNMP Agent

Example for Outputting Information to an SNMP Agent

After information is output to an SNMP agent, the NMS can receive the information from the Device through an SNMP agent.

Networking Requirements

On the network shown in Figure 19-4, a Device is connected to the NMS. To monitor the Device operation in real time or collect important information about the Device operation, you can output traps to an SNMP agent. The SNMP agent forwards the information to an NMS.

NOTE:

In this example, traps are output to a remote terminal.

Figure 19-4 Outputting traps to an SNMP agent

NOTE:

Interfaces 1 in this example are GE 0/1/0.

Configuration Roadmap

The configuration roadmap is as follows:

  1. Enable the information management function.

  2. Configure the channel through which traps are output to an SNMP agent and the module of which traps are to be output.

  3. Output traps to the SNMP agent.

  4. Output traps to an NMS through an SNMP agent.

Data Preparation

To complete the configuration, you need the following data:

  • Information channel number

  • Module and severity of the traps to be output

Procedure

  1. Configure available routes between the Router and the NMSs. Details for the configuration procedure are not provided here.
  2. Enable the information management function.

    <HUAWEI> system-view
    [~HUAWEI] sysname Device
    [*HUAWEI] commit
    [~Device] info-center enable

  3. Configure the channel through which traps are output to an SNMP agent and the module of which traps are to be output.

    # Output traps whose severity is informational or higher to channel 7.

    [*Device] info-center source im channel channel7 trap level informational

  4. Output traps to an SNMP agent.

    [*Device] info-center snmp channel channel7

  5. Output traps to the NMS through an SNMP agent.

    # Enable the SNMP agent function, with the SNMP version of SNMPv2c.

    [*Device] snmp-agent sys-info version v2c

    # Enable the SNMP agent to send traps.

    [*Device] snmp-agent trap enable
    [*Device] snmp-agent target-host trap address udp-domain 10.1.1.1 params securityname public

  6. Verify the configuration.

    # Display the channel used by the SNMP agent to output traps.

    [~Device] display info-center
    Information Center:enabled
    Log host:
    Console:
            channel number : 0, channel name : console
    Monitor:
            channel number : 1, channel name : monitor
    SNMP Agent:
            channel number : 7, channel name : channel7
    Log buffer:
            enabled,max buffer size 10240, current buffer size 512,
    current messages 10, channel number : 4, channel name : logbuffer
    dropped messages 0, overwritten messages 0
    Trap buffer:
            enabled,max buffer size 1024, current buffer size 256,
    current messages 3, channel number:3, channel name:trapbuffer
    dropped messages 0, overwritten messages 0
    logfile:
            channel number : 9, channel name : channel9, language : English
    Information timestamp setting:
            log - date, trap - date, debug - date millisecond
    

    # Display the information output to the SNMP agent through the channel.

    [~Device] display channel 7
    channel number:7, channel name:channel7
    ModuID   Name          Enable LogLevel      Enable TrapLevel     Enable DebugLevel   
    ffffffff default       Y      debugging     Y      debugging     N      debugging    
    00000957 IM            Y      debugging     Y      informational N      debugging  

    # Display trap information output by the SNMP agent to the NMS.

    [*Device] display snmp-agent target-host
    Target-host NO. 1
    -----------------------------------------------------------
      Host-name                        : targetHost_2
      IP-address                       : 10.1.1.1
      Source interface                 : -
      VPN instance                     : -
      Security name                    : %^%#-(}fC-|38%RgqpW$+c^UU"AH()$q#K26fL2X5XK7%^%#
      Port                             : 162
      Type                             : trap
      Version                          : v2c
      Level                            : No authentication and privacy
      NMS type                         : HW NMS
      With ext-vb                      : No
      Notification filter profile name : -  
    -----------------------------------------------------------

Configuration Files

#
sysname Device
#
info-center source im channel 7 trap level informational
info-center snmp channel 7
#
interface GigabitEthernet0/1/0
 undo shutdown
 ip address 10.1.1.2 255.255.255.0
#
snmp-agent
#
snmp-agent sys-info version v2c v3
snmp-agent target-host trap address udp-domain 10.1.1.1 params securityname cipher %^%#-(}fC-|38%RgqpW$+c^UU"AH()$q#K26fL2X5XK7%^%#
#
snmp-agent trap enable
#
return
Download
Updated: 2019-01-02

Document ID: EDOC1100058392

Views: 20526

Downloads: 33

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next