No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Routing 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - IP Routing
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the OSPFv3 GR Helper

Configuring the OSPFv3 GR Helper

To avoid traffic interruption and route flapping caused by the active/standby switchover, you can enable OSPFv3 GR.

Context

GR ensures normal traffic forwarding and non-stop forwarding of key services during the restart of routing protocols. GR is one of high availability (HA) technologies. HA technologies comprise a set of comprehensive techniques, such as fault-tolerant redundancy, link protection, faulty node recovery, and traffic engineering. As a fault-tolerant redundancy technology, GR is widely used to ensure non-stop forwarding of key services during master/slave main control board switchover and system upgrade.

NOTE:

The NE supports only the GR Helper.

Pre-configuration Tasks

Before configuring OSPFv3 GR, complete the following tasks:

  • Configure a link layer protocol.

  • Configure IP addresses for interfaces to ensure that neighboring nodes are reachable at the network layer.

  • Configure basic OSPFv3 functions.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run ospfv3 process-id

    The OSPFv3 view is displayed.

  3. Configure a basic ACL:

    1. Run helper-role [ { ip-prefix ip-prefix-name | acl-number acl-number | acl-name acl-name } | max-grace-period period | planned-only | lsa-checking-ignore ] *

      OSPFv3 GR is enabled.

    2. Run quit

      Return to the system view.

    3. Run acl ipv6 { name basic-acl6-name { basic | [ basic ] number basic-acl6-number } | [ number ] basic-acl6-number } [ match-order { config | auto } ]

      The basic ACL view is displayed.

    4. Run rule [ rule-id ] [ name rule-name ] { deny | permit } [ fragment | source { source-ipv6-address { prefix-length | source-wildcard } | source-ipv6-address/prefix-length | any } | time-range time-name | [ vpn-instance vpn-instance-name | vpn-instance-any ] ] *

      A rule is configured for the basic ACL.

      When the rule command is run to configure rules for a named ACL, only the source address range specified by source and the time period specified by time-range are valid as the rules.

  4. Run commit

    The configuration is committed.

Checking the Configurations

Run the following command to check the preceding configuration:

  • Run the display ospfv3 [ process-id ] graceful-restart-information command to view the OSPFv3 GR Helper status.

<HUAWEI> display ospfv3 1 graceful-restart-information
            OSPFv3 Router with ID (0.0.0.0) (Process 1)

  Helper capability                : enabled
  Helper support                   : planned and un-planned, strict lsa check
  Max Grace-Period Configured      : 1800 Sec
  Last Helper-exit Reason          : none
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058916

Views: 34222

Downloads: 51

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next