No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Routing 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - IP Routing
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Controlling the Sending and Receiving of RIPng Packets

Controlling the Sending and Receiving of RIPng Packets

By controlling the sending and receiving of RIPng packets, you can optimize the RIPng performance.

Applicable Environment

To meet the requirements of complex networking, accurately control the sending and receiving of RIPng packets.

Pre-configuration Tasks

Before configuring a NE to control the sending and receiving of RIPng packets, complete the following tasks:

Configuration Procedure

Perform one or more of the following configuration tasks (excluding "Checking the Configuration" ) as required.

Disabling Receiving of RIPng Packets on an Interface

Disabling interfaces from receiving RIPng packets is a method of preventing routing loops.

Context

When a device running RIPng is connected to a network running other routing protocols, you can run the undo ripng input command on the interface that connects the device to the network to prevent the interface from receiving useless packets from the network.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. Run undo ripng input

    The interface is disabled from receiving RIPng packets.

    By default, an interface is allowed to receive RIPng packets.

  4. Run commit

    The configuration is submitted.

Disabling Sending of RIPng Packets on an Interface

Disabling an interface from sending RIPng packets is a method of preventing routing loops.

Context

When a device running RIPng is connected to a network running other routing protocols, you can run the undo ripng output command on the interface that connects the device to the network to prevent the interface from sending useless packets to the network.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. Run undo ripng output

    The interface is disabled from sending RIPng packets.

    By default, an interface is allowed to send RIPng packets.

  4. Run commit

    The configuration is submitted.

Setting the Interval for Sending Update Packets and the Maximum Number of Packets Sent Each Time

By setting the interval for sending packets and the maximum number of packets to be sent each time, you can optimize the RIPng performance.

Context

Perform the following steps on the RIPng NE:

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. Run ripng pkt-transmit { interval interval | number pkt-count }*

    The interval for sending RIPng Update packets and the maximum number of packets sent each time are set on the specified interface.

  4. Run commit

    The configuration is submitted.

Verifying the Configuration of Controlling the Sending and Reveiving of RIPng Packets

After controlling the sending and receiving of RIPng packets, verify the routing information in the RIPng database.

Prerequisites

Configurations have been performed to control the sending and receiving of RIPng packets.

Procedure

  • Run the display ripng process-id database [ verbose ] [ destination-address destination-address [ mask-length ] ] [ interface interface-type interface-number [ neighbor-address neighbor-address ] ] command to check the routing information in the RIPng database.

Example

Run the display ripng process-id database command to view the routing information in the RIPng database.

<HUAWEI> display ripng 100 database
   2001:DB8:8::8/128,
        cost 0, Imported
   2001:DB8:10::/64,
       via FE80::2E0:E6FF:FE1B:8242, cost 1
   2001:DB8:10::/64,
       via FE80::2E0:E6FF:FE1B:8242, cost 1
   2001:DB8:10::/64,
       via FE80::2E0:E6FF:FE1B:8142, cost 1
   2001:DB8:10::/64,
       via FE80::2E0:E6FF:FE1B:8142, cost 1
   2001:DB8:12::/64,
        cost 0, RIPng-interface
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058916

Views: 35009

Downloads: 51

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next