No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Routing 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - IP Routing
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring an IPv6 Prefix Set

Configuring an IPv6 Prefix Set

IPv6 prefix sets apply to all dynamic routing protocols and can be used to match source, destination, and next hop IPv6 addresses. This section describes how to configure IPv6 prefix sets.

Procedure

  • Configure an IPv6 prefix set using the paragraph editing mode.
    1. Run the edit xpl ipv6-prefix-list ipv6-prefix-list-name command to enter the IPv6 prefix set paragraph editing interface view.
    2. Press i to enter the text editing mode.

      NOTE:

      Sets or route-filters can be configured only in the text editing mode. If you exit from the text editing mode, you can perform shortcut key operations only.

    3. Configure a start clause (xpl ipv6-prefix-list ipv6-prefix-list-name) for an IPv6 prefix set.
    4. Configure elements (IPv6 addresses with masks, 2001:db8:0:1::64 for example) for the set and separate every two neighboring elements with a comma (,). You can use eq, ge, or le to specify the mask length.
    5. Configure an end clause (end-list) for the IPv6 prefix set.
    6. Press Esc to exit from the text editing mode.
    7. Press :wq and Enter to save the configurations and exit from the global variable set paragraph editing interface view.

      NOTE:

      A message is displayed for you to confirm whether to commit the configurations when you attempt to exit from the global variable set paragraph editing interface view. To commit the configurations, press Y.

      To exit from the global variable set paragraph editing interface view without saving the configurations, press :q! and Enter.

  • Configure an IPv6 prefix set using the line editing mode.
    1. Run the system-view command to enter the system view.
    2. Run the xpl ipv6-prefix-list ipv6-prefix-list-name command to enter the IPv6 prefix set view.
    3. Configure elements (IPv6 addresses with masks, such as 2001:db8:0:1::64) for the set and separate every two neighboring elements with a comma (,). You can use eq, ge, or le to specify the mask length.
    4. Run the end-list command to conclude the configuration of the IPv6 prefix set, exit the IPv6 prefix set view, and return to the system view.
    5. Run the commit command to commit the configuration.

Example

NOTE:

If only paragraph editing is used as an example, the corresponding line editing is similar. To use the line editing mode, perform the operations described in paragraph editing.

For detailed set and route-filter configuration steps, see Configuration Procedures of Sets and Route-Filters Using the Paragraph Editing Mode. For details about XPL clauses, see XPL Paragraph Editing Clauses.

Objective Configure an IPv6 prefix set to match the routes in network segments 2001:db8:0:1::/64, 2001:db8:1:1::/64, and 2001:db8:1:2::/64.
Configuration Example 1
<HUAWEI> edit xpl ipv6-prefix-list aaa

xpl ipv6-prefix-list aaa
2001:db8:0:1:: 64,
2001:db8:1:1:: 64,
2001:db8:1:2:: 64
end-list

The IPv6 prefix set aaa includes three elements and matches the routes in network segments 2001:db8:0:1::/64, 2001:db8:1:1::/64, and 2001:db8:1:2::/64.

Objective Configure an IPv6 prefix set to match the routes in network segment 2001:db8:0:1::/64 with the mask length ranging from 96 to 100 bits, the routes in network segment 2001:db8:1:1::/64 with the mask length greater than or equal to 100 bits, and the routes in network segment 2001:db8:1:2::/64 with the mask length of 96 bits.
Configuration Example 2
<HUAWEI> edit xpl ipv6-prefix-list aaa

xpl ipv6-prefix-list aaa
2001:db8:0:1:: 64 ge 96 le 100,
2001:db8:1:1:: 64 le 100,
2001:db8:1:2:: 64 eq 96
end-list

The IPv6 prefix set bbb includes three elements and matches the routes in network segment 2001:db8:0:1::/64 with the mask length ranging from 96 to 100 bits, the routes in network segment 2001:db8:1:1::/64 with the mask length greater than or equal to 100 bits, and the routes in network segment 2001:db8:1:2::/64 with the mask length of 96 bits.

Objective Configure a route-filter to deny the routes that match IPv6 prefix set bbb and the routes that match neither IPv6 prefix set aaa nor bbb and permit the routes that do not match bbb but match aaa and increase their MED values by 10.
Reference Example
<HUAWEI> edit xpl route-filter r1

xpl route-filter r1
if ip route-destination in bbb then
refuse
elseif ip route-destination in aaa then
apply med + 10
else
refuse
endif
end-filter

The route-filter r1 references two IPv6 destination address prefix sets (aaa and bbb), denies the routes that match IPv6 destination address prefix set bbb, permits the routes that do not match bbb but match aaa and increases their MED values by 10, and denies all other routes.

Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058916

Views: 38173

Downloads: 57

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next