No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - System Monitor 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - System Monitor
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Test Results to Be Sent to the FTP Server

Configuring Test Results to Be Sent to the FTP Server

The NMS needs to obtain test results of devices. If the NMS cannot poll test results in time, test results are lost. Delivering the test results to the FTP server can save the test results to the maximum extent.

Usage Scenario

The result table of NQA test instances records results of each test type. A maximum of 5000 test result records are supported in total. If the number of records reaches 5000, test results are uploaded and the new test result overwrites the earliest one. If the NMS cannot poll test results in time, test results are lost. You can send the statistics on the test results that reach the capacity of the local storage or periodically send the statistics to the FTP server for storage through FTP. This can effectively prevent the loss of test results and facilitate network management based on the analysis of test results at different times.

Pre-configuration Tasks

Before configuring test results to be sent to the FTP server, complete the following tasks:

  • Configure the FTP server.

  • Configure a reachable route between the NQA client and the NMS.

  • Configure a test instance.

Data Preparation

Before configuring test results to be sent to the FTP server, you need the following data.

No.

Data

1

IP address of the FTP server

2

User name and password used for logging in to the FTP server

3

Name of a file in which test results are saved through FTP

4

Interval at which test results are uploaded through FTP

Setting Parameters for Configuring Test Results to Be Sent to the FTP Server

Before starting a test instance, set the IP address of the FTP server that receives test results, user name and password for logging in to the FTP server, name of the file in which test results are saved, interval at which test results are uploaded, and retransmission times.

Context

Perform the following operations on the NQA client.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run nqa upload test-type { icmp | icmpjitter | jitter | udp } ftp ipv4 ipv4-address file-name file-name [ vpn-instance vpn-instance-name ] [ port port-number ] username user-name password password [ interval upload-interval ] [ retry retry-times ]

    A device is enabled to upload test result files onto a specified server.

  3. Run commit

    The configuration is committed.

Starting a Test Instance

After a test instance is started, test results are periodically recorded in files.

Context

Perform the following operations on the NQA client.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run nqa test-instance admin-name test-name

    The NQA view is displayed.

  3. Run test-type { icmp | icmpjitter | jitter | udp }

    A test instance type is set.

  4. Run destination-address ipv4 ip-address

    A destination address is configured.

  5. (Optional) Run destination-port port-number

    A destination port number is configured.

  6. Run start

    An NQA test instance is started.

    An NQA test instance can be started immediately, at a specified time, or after a specified delay.

    • Run start now [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

      The test instance is started immediately.

    • Run start at [ yyyy/mm/dd ] hh:mm:ss [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

      The test instance is started at a specified time.

    • Run start delay { seconds second | hh:mm:ss } [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

      The test instance is started after a specified delay.

    • Run start daily hh:mm:ss to hh:mm:ss [ begin { yyyy/mm/dd | yyyy-mm-dd } ] [ begin { yyyy/mm/dd | yyyy-mm-dd } ]

      The test instance is started at a specified time every day.

  7. Run commit

    The configuration is committed.

Verifying the Configuration of Test Results to Be Sent to the FTP Server

After configuring test results to be sent to the FTP server, verify the configuration.

Prerequisites

Test results have been configured to be sent to the FTP server.

Procedure

  1. Run the display nqa upload file-info command to check information about files that a device is uploading and has attempted to upload onto a server.

Example

Run the display nqa upload file-info command. The command output shows information about files that a device is uploading and has attempted to upload onto a server.

<HUAWEI> display nqa upload file-info
The total number of upload file records is : 2                                  
---------------------------------------------------------------                 
FileName   : NQA_38ba47987301_icmp_20171014112319701_test1.xml                  
Status     : Upload success                                                     
RetryTimes : 3                                                                  
UploadTime : 2017-10-14 11:23:21.697                                            
                                                                                
---------------------------------------------------------------
FileName   : NQA_38ba47987301_icmp_20171014112421710_test1.xml                  
Status     : Uploading                                                          
RetryTimes : 3                                                                  
UploadTime : --                                                                 
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058924

Views: 7111

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next