No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - System Monitor 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - System Monitor
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Using a Ping/Tracert Operation on an EVPN VPWS Network

Using a Ping/Tracert Operation on an EVPN VPWS Network

If an EVPN VPWS tunnel fault occurs, use a ping/tracert operation to check EVPN VPWS LSPs and fast locate a tunnel forwarding fault.

Checking EVPN VPWS Network Connectivity Using a Ping Operation

Use ping operations to check EVPN VPWS LSPs and fast locate an EVPN VPWS tunnel forwarding fault.

Context

After EVPN VPWS configurations are complete, perform the following operation in any view of the client.

Procedure

  • Check EVPN VPWS tunnel connectivity when the EVPN VPWS public network is MPLS.

    Run ping evpn vpws local-ce-id remote-ce-id [ -a source-ip | -c count | -exp exp-value | -m interval | -s packet-size | -t time-out | -r reply-mode ] *

    The EVPN VPWS tunnel status is checked, and an abnormality on the EVPN VPWS tunnel in the Up state is located.

    For example:

    # Perform a ping test on the EVPN VPWS tunnel.

    <HUAWEI> ping evpn vpws 1 2 -c 2
    EVPN VPWS PING FEC: Local Evpn Vpws Id = 1, Remote Evpn Vpws Id = 2 : 100 data bytes, press CTRL_C to break
    Reply from 100.1.1.1: bytes=100 Sequence=1 time=11 ms
    Reply from 100.1.1.1: bytes=100 Sequence=2 time=15 ms
    --- FEC: Local CeId = 1, Remote CeId = 2 ping statistics ---
    2 packet(s) transmitted
    2 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 11/13/15 ms

Checking EVPN VPWS Network Connectivity Using a Tracert Operation

Use tracert operations to locate an EVPN VPWS tunnel forwarding fault.

Context

After EVPN VPWS configurations are complete, perform the following operation in any view of the client.

Procedure

  • Check EVPN VPWS tunnel connectivity when the EVPN VPWS public network is MPLS.

    Run tracert evpn vpws local-ce-id remote-ce-id [ -a source-ip | -exp exp-value | -s packet-size | -t time-out | -h max-ttl | -r reply-mode ] * [ pipe | uniform ]

    The EVPN VPWS tunnel status is checked, and an abnormal node on the EVPN VPWS tunnel in the Down state is located.

    For example:

    # Perform a tracert test on the EVPN VPWS tunnel.

    <HUAWEI> tracert evpn vpws 1 2
    EVPN VPWS TRACE FEC: Local Evpn Vpws Id = 1, Remote Evpn Vpws Id = 2 , press CTRL_C to break 
    TTL    Replier            Time    Type      Downstream
     0                                Ingress   12.1.1.2/[3 1 32927] 
     1     12.1.1.2           52 ms   Egress 

Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058924

Views: 6997

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next