No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the PW Redundancy Configuration

Verifying the PW Redundancy Configuration

Prerequisites

The configurations of the integrated IP RAN with Ethernet NodeBs are complete.

Procedure

  • Run the display mpls l2vc [ vc-id | interface interface-type interface-number ] command to check local VPWS PW information.
  • Run the display mpls switch-l2vc [ ip-address vc-id encapsulation encapsulation-type | state { down | up } | brief ] command to check information about the PW switching on S-PEs.

Example

Run the display mpls l2vc [ vc-id | interface interface-type interface-number ] command. The command output shows that the VC status is Up.

<HUAWEI> display mpls l2vc
 total LDP VC : 1     1 up       0 down

 *client interface          : GigabitEthernet0/1/1.1 is up
  Administrator PW          : no
  session state             : up
  AC status                 : up
  VC state                  : up
  Label state               : 0
  Token state               : 0
  VC ID                     : 100
  VC type                   : VLAN
  destination               : 192.3.3.3
  local VC label            : 18           remote VC label      : 18
  control word              : disable
  remote control word       : disable
  forwarding entry          : exist
  local group ID            : 0
  remote group ID           : 0
  local AC OAM State        : up
  local PSN OAM State       : up
  local forwarding state    : forwarding
  local status code         : 0x0
  remote AC OAM state       : up
  remote PSN OAM state      : up
  remote forwarding state   : forwarding
  remote status code        : 0x0
  ignore standby state      : no
  BFD for PW                : unavailable
  VCCV State                : up
  manual fault              : not set
  active state              : active
  OAM Protocol              : --
  OAM Status                : --
  OAM Fault Type            : --
  PW APS ID                 : --
  PW APS Status             : --
  TTL Value                 : 1
  link state                : up
  local VC MTU              : 1500         remote VC MTU        : 1500
  local VCCV                : alert ttl lsp-ping bfd
  remote VCCV               : alert ttl lsp-ping bfd
  tunnel policy name        : --
  PW template name          : --
  primary or secondary      : primary
  load balance type         : flow
  Access-port               : false
  Switchover Flag           : false
  VC tunnel info            : 1 tunnels
    NO.0  TNL type          : ldp   , TNL ID : 0x0000000001004c4e42
  create time               : 0 days, 0 hours, 17 minutes, 58 seconds
  up time                   : 0 days, 0 hours, 16 minutes, 50 seconds
  last change time          : 0 days, 0 hours, 16 minutes, 50 seconds
  VC last up time           : 2012/12/05 02:50:41
  VC total up time          : 0 days, 0 hours, 16 minutes, 50 seconds
  CKey                      : 1
  NKey                      : 1493172332
  PW redundancy mode        : frr
  AdminPw interface         : --
  AdminPw link state        : --
  Forward state             : send inactive, receive inactive 
  Diffserv Mode             : uniform
  Service Class             : --
  Color                     : --
  DomainId                  : --
  Domain Name               : --

Run the display mpls switch-l2vc command. The command output shows that the VC status is Up.

<HUAWEI> display mpls switch-l2vc
Total Switch VC : 1, 1 up, 0 down

*Switch-l2vc type             : LDP<---->LDP
 Peer IP Address              : 2.2.2.2, 1.1.1.1
 VC ID                        : 22, 11
 VC Type                      : VLAN
 VC State                     : up
 VC StatusCode                |PSN |OAM | FW |    |PSN |OAM | FW |
                   -Local VC :| UP | UP | UP |    | UP | UP | UP |
                   -Remote VC:| UP | UP | UP |    | UP | UP | UP |
 Session State                : up, up
 Local/Remote Label           : 21504/21504, 21505/21504
 InLabel Status               : 0 , 0 
 Local/Remote MTU             : 1500/1500, 1500/1500
 Local/Remote Control Word    : Enable/Enable, Enable/Enable
 Local/Remote VCCV Capability : alert lsp-ping bfd/None, alert lsp-ping bfd/None
 Switch-l2vc tunnel info      :
                                1 tunnels for peer 2.2.2.2
                                NO.0  TNL Type : lsp   , TNL ID : 0x801000
                                1 tunnels for peer 1.1.1.1
                                NO.0  TNL Type : lsp   , TNL ID : 0x801020
 CKey                         : 33, 31
 NKey                         : 32, 30
 Tunnel policy                : --, --
 Control-Word transparent     : NO
 Create time                  : 0 days, 0 hours, 0 minutes, 14 seconds
 UP time                      : 0 days, 0 hours, 0 minutes, 10 seconds
 Last change time             : 0 days, 0 hours, 0 minutes, 14 seconds
 VC last up time : 2012-03-12 12:31:31
 VC total up time: 0 days, 2 hours, 12 minutes, 51 seconds
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 32124

Downloads: 59

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next