No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the BGP VPWS FRR Configuration

Verifying the BGP VPWS FRR Configuration

Prerequisites

VPWS FRR has been configured.

Procedure

  • Run the display mpls l2vpn connection l2vpn-name [ remote-ce remote-ce-id | down | up | verbose ] command to check BGP VPWS connection information.
  • Run the display mpls l2vpn oam-mapping [ interface interface-type interface-number ] command to check OAM mapping information.

Example

Run the display mpls l2vpn connection interface command. The command output shows BGP VPWS connection information on the specified AC interface.

<HUAWEI> display mpls l2vpn connection interface gigabitethernet 0/1/0.1
conn-type: remote
     local vc state:             up
     remote vc state:            up
     local ce-id:                2
     local ce name:              ce2
     remote ce-id:               6
     intf(state,encap):          GigabitEthernet0/1/0.1(up,vlan)
     peer id:                    3.3.3.3
     route-distinguisher:        100:3
     local vc label:             382838
     remote vc label:            375730
     tunnel policy:              default 
     CKey:                       849
     NKey:                       2382370027
     primary or secondary:       primary
     forward entry exist or not: true
     forward entry active or not:true
     manual fault set or not:    not set 
     AC OAM state:               up 
     BFD for PW session index:   -- 
     BFD for PW state:           invalid 
     BFD for LSP state:          true
     Local C bit is set 
     Remote C bit is set 
     tunnel type:                ldp
     tunnel id:                  0x0000000001004c4b43

conn-type: remote
     local vc state:             up
     remote vc state:            up
     local ce-id:                2
     local ce name:              ce2
     remote ce-id:               10
     intf(state,encap):          GigabitEthernet0/1/0.1(up,vlan)
     peer id:                    1.1.1.1
     route-distinguisher:        100:3
     local vc label:             382842
     remote vc label:            375754
     tunnel policy:              default 
     CKey:                       2432
     NKey:                       2382370029
     primary or secondary:       secondary
     forward entry exist or not: true
     forward entry active or not:false
     manual fault set or not:    not set 
     AC OAM state:               up 
     BFD for PW session index:   -- 
     BFD for PW state:           invalid 
     BFD for LSP state:          true
     Local C bit is set 
     Remote C bit is set 
     tunnel type:                ldp
     tunnel id:                  0x0000000001004c4b42

 Reroute policy         : delay 30 s, resume 10 s
 Reason of last reroute : --
 Time of last reroute   : -- days, -- hours, -- minutes, -- seconds
 delay timer ID         : -- residual time :--
 resume timer ID        : -- residual time :--

Run the display mpls l2vpn oam-mapping interface command. The command output shows OAM mapping information.

<HUAWEI> display mpls l2vpn oam-mapping interface gigabitethernet0/1/0.1
 AC OAM Info:
  EOAM Type      : 802.1ag
  MaIndex        : 0x2
  AC OAM State   : Up
  OAM-mapping    : Enable
 PSN info:
  Local CE-ID    : 2
  Remote CE-ID   : 6
  VC status      : Primary
  Link State     : Up
  Active State   : Active
  BFD for PW     : Enable
  BFDSessionIndex:--,    BFD State:    invalid State:0
  BFD for LSP    : --    TunnelNum: --    PSN State : --
  Local CE-ID    : 2
  Remote CE-ID   : 10
  VC status      : Secondary
  Link State     : Up
  Active State   : Inactive
  BFD for PW     : Enable
  BFDSessionIndex:--,   BFD State :    invalid State:0
  BFD for LSP    : --    TunnelNum: --    PSN State : --
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 32533

Downloads: 59

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next