No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the Inter-AS VPLS Configuration

Verifying the Inter-AS VPLS Configuration

After configuring inter-AS VPLS, check VSI and PW information.

Prerequisites

Inter-AS VPLS has been configured.

Procedure

  • Run the display vsi [ name vsi-name ] [ verbose ] command to check VSI information.
  • Run the display bgp l2vpn-ad peer [ [ ipv4-address ] verbose ] command on a PE or ASBR to check BGP VPLS peers information.
  • Run the display vpls connection [ bgp | vsi vsi-name ] [ down | up ] [ verbose ] command on a PE to check PW information.
  • Run the display bgp routing-table label statistics command on a PE or ASBR to check labeled IPv4 routes.
  • Run the display vsi bgp-ad remote vpls-id vpls-id command to check information about a specified remote PE.

Example

Run the display vsi [ name vsi-name ] [ verbose ] command. The command output shows that VSI State is up. If you specify verbose, the command output shows that Signaling is ldp and VSI State is up.

<HUAWEI> display vsi name abc verbose
***VSI Name                : abc
    Administrator VSI      : no
    Isolate Spoken         : disable
    VSI Index              : 2
    PW Signaling        : ldp
    Bridge-domain Mode     : disable
    Member Discovery Style : static
    PW MAC Learn Style     : unqualify
    Encapsulation Type     : vlan
    MTU                    : 1500
    Diffserv Mode          : uniform
    Service Class          : --
    Color                  : --
    DomainId               : 255
    Domain Name            :
    Ignore AcState         : disable
    P2P VSI                : disable
    Create Time            : 1 days, 1 hours, 43 minutes, 51 seconds
    VSI State              : up
    Resource Status        : --

    VSI ID                 : 9
   *Peer Router ID         : 3.3.3.3
    primary or secondary   : primary
    ignore-standby-state   : no
    VC Label               : 19457
    Peer Type              : dynamic
    Session                : up
    Tunnel ID              : 0x801019
    Broadcast Tunnel ID    : 0x801019
    CKey                   : 39
    NKey                   : 10
    StpEnable              : 0
    PwIndex                : 0

    Interface Name         : GigabitEthernet0/1/1.16
    State                  : up
    Last Up Time           : 2014/09/30 010:29:37
    Total Up Time          : 1 days, 1 hours, 42 minutes, 18 seconds            

Run the display vpls connection command on a PE or ASBR. The command output shows that the PW status is up.

<HUAWEI> display vpls connection
1 total connections,
connections: 1 up, 0 down, 0 ldp, 1 bgp, 0 bgpad 

VSI Name: v1                               Signaling: bgp
SiteID  RD                      PeerAddr          InLabel   OutLabel  VCState
2       200:1                   4.4.4.4           25602     25601     up

Run the display bgp routing-table label command on a PE or ASBR. The command output shows information about labeled IPv4 routes.

<HUAWEI> display bgp routing-table label
 Total Number of Routes: 1


 BGP Local router ID is 1.1.1.1
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
        Network           NextHop           In/Out Label
 *>i    4.4.4.4           2.2.2.2           NULL/15361

Run the display vsi bgp-ad remote vpls-id vpls-id command. The command output shows member information about the peer PE with the VPLS ID being 100:1.

<HUAWEI> display vsi bgp-ad remote vpls-id 100:1
BGP AD Network Layer Reachability Information
-----------------------------------------------
 *Peer             :4.4.4.4
  VPLS ID          :100:1
  VSI ID           :4.4.4.4
  VSI index        :2
  Export vpn target:200:1 
-----------------------------------------------
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 28196

Downloads: 53

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next