No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the Configuration of VPWS accessing VPLS

Verifying the Configuration of VPWS accessing VPLS

After configuring VPWS accessing VPLS, check VPWS and VPLS information, such as PW, outbound interface, VSI, and tunnel policy information.

Prerequisites

VPWS accessing VPLS has been configured.

Procedure

  • Run the display mpls l2vc [ vc-id | interface interface-type interface-number ] command to check LDP VPWS information.
  • Run the display vsi [ name vsi-name ] [ verbose ] command to check VSI information.
  • Run the display vsi mac-withdraw loop-detect command to check MAC withdraw loop detection information.

Example

Run the display mpls l2vc command. The command output shows that destination is the peer IP address of the specified VC and VC state is up.

<HUAWEI> display mpls l2vc
total LDP VC : 1     1 up       0 down
 *client interface          : GigabitEthernet0/1/0.1 is up
  Administrator PW          : no
  session state             : up
  AC status                 : up
  VC state               : up
  Label state               : 0
  Token state               : 0
  VC ID                     : 100
  VC type                   : VLAN
  destination               : 1.1.1.9
  local VC label            : 23           remote VC label      : 24
  control word              : disable
  remote control word       : disable
  forwarding entry          : exist
  local group ID            : 0
  remote group ID           : 0
  local AC OAM State        : up
  local PSN OAM State       : up
  local forwarding state    : forwarding
  local status code         : 0x0
  remote AC OAM state       : up
  remote PSN OAM state      : up
  remote forwarding state   : forwarding
  remote status code        : 0x0
  ignore standby state      : no
  BFD for PW                : unavailable
  VCCV State                : up
  manual fault              : not set
  active state              : active
  OAM Protocol              : --
  OAM Status                : --
  OAM Fault Type            : --
  PW APS ID                 : --
  PW APS Status             : --
  TTL Value                 : 1
  link state                : up
  local VC MTU              : 1500         remote VC MTU        : 1500
  local VCCV                : alert ttl lsp-ping bfd
  remote VCCV               : alert ttl lsp-ping bfd
  tunnel policy name        : --
  PW template name          : --
  primary or secondary      : primary
  load balance type         : flow
  Access-port               : false
  Switchover Flag           : false
  VC tunnel info            : 1 tunnels
    NO.0  TNL type          : ldp   , TNL ID : 0x0000000001004c4e42
  create time               : 0 days, 0 hours, 26 minutes, 33 seconds
  up time                   : 0 days, 0 hours, 21 minutes, 50 seconds
  last change time          : 0 days, 0 hours, 21 minutes, 50 seconds
  VC last up time           : 2012/12/05 08:13:31
  VC total up time          : 0 days, 0 hours, 21 minutes, 50 seconds
  CKey                      : 65
  NKey                      : 1493172339
  PW redundancy mode        : frr
  AdminPw interface         : --
  AdminPw link state        : --
  Forward state             : send inactive, receive inactive 
  Diffserv Mode             : uniform
  Service Class             : --
  Color                     : --
  DomainId                  : --
  Domain Name               : --

Run the display mpls static-l2vc [ vc-id | interface interface-type interface-number | state { down | up } ] command. The command output shows that VC State is up.

<HUAWEI> display mpls static-l2vc
 Total svc connections:  1,  1 up,  0 down

 *Client Interface     : GigabitEthernet0/1/0  is up
  AC Status            : up
  VC State           : up
  VC ID                : 0
  VC Type              : VLAN
  Destination          : 1.1.1.9
  Transmit VC Label    : 100
  Receive VC Label     : 200
  Label Status         : 0
  Token Status         : 0
  Control Word         : Disable
  VCCV Capability      : alert ttl lsp-ping bfd 
  active state         : active
  OAM Protocol         : --
  OAM Status           : --
  OAM Fault Type       : --
  PW APS ID            : --
  PW APS Status        : --
  TTL Value            : 1
  Link State           : up
  Tunnel Policy Name   : --
  PW Template Name     : --
  Main or Secondary    : Main
  load balance type    : flow
  Access-port          : false
  VC tunnel/token info : 1 tunnels/tokens
  NO.0  TNL Type       : ldp   , TNL ID : 0x0000000001004c4b42
  Create time          : 0 days, 0 hours, 11 minutes, 21 seconds
  UP time              : 0 days, 0 hours, 1 minutes, 29 seconds
  Last change time     : 0 days, 0 hours, 1 minutes, 29 seconds
  VC last up time      : 2015/05/30 17:34:22
  VC total up time     : 0 days, 0 hours, 1 minutes, 29 seconds
  CKey                 : 33
  NKey                 : 2818572439

Run the display vsi [ name vsi-name ] [ verbose ] command. The command output shows that VSI State is up. If verbose is configured, the command output also shows that Signaling is ldp and VSI State is up.

<HUAWEI> display vsi name v100 verbose
 ***VSI Name               : v100
    Work Mode              : normal
    Administrator VSI      : no
    Isolate Spoken         : disable
    VSI Index              : 1
    PW Signaling           : ldp
    Member Discovery Style : --
    Bridge-domain Mode     : disable
    PW MAC Learn Style     : unqualify
    Encapsulation Type     : vlan
    MTU                    : 1500
    Diffserv Mode          : uniform
    Service Class          : --
    Color                  : --
    DomainId               : 255
    Domain Name            : 
    Ignore AcState         : disable
    P2P VSI                : disable
    Create Time            : 0 days, 0 hours, 9 minutes, 44 seconds
    VSI State            : up
    Resource Status        : --

    VSI ID                 : 100
    LDP MAC-WITHDRAW       : mac-withdraw Enable
   *Peer Router ID         : 3.3.3.9
    primary or secondary   : primary
    ignore-standby-state   : no
    VC Label               : 400
    Peer Type              : static
    Tunnel ID              : 0x0000000001004c4b43 
    Broadcast Tunnel ID    : --
    Broad BackupTunnel ID  : -- 
    CKey                   : 1
    NKey                   : 1358954644
    Stp Enable             : 0
    PwIndex                : 1
    Control Word           : disable
   *Peer Router ID         : 4.4.4.9
    primary or secondary   : primary
    ignore-standby-state   : no
    VC Label               : 100
    Peer Type              : static
    Tunnel ID              : 0x0000000001004c4b44 
    Broadcast Tunnel ID    : --
    Broad BackupTunnel ID  : -- 
    CKey                   : 2
    NKey                   : 1358954645
    Stp Enable             : 0
    PwIndex                : 2
    Control Word           : disable
                
  **PW Information:
                
   *Peer Ip Address        : 3.3.3.9
    PW State             : up
    Local VC Label         : 400
    Remote VC Label        : 300
    Remote Control Word    : disable
    PW Type                : label
    Tunnel ID              : 0x0000000001004c4b43 
    Broadcast Tunnel ID    : --
    Broad BackupTunnel ID  : --
    Ckey                   : 1
    Nkey                   : 1358954644
    Main PW Token          : 0x0
    Slave PW Token         : 0x0
    Tnl Type               : ldp
    OutInterface           : 
    Backup OutInterface    : --
    Stp Enable             : 0
    Mac Flapping           : 0
    PW Last Up Time        : 2015/05/30 17:29:56
    PW Total Up Time       : 0 days, 0 hours, 9 minutes, 42 seconds
   *Peer Ip Address        : 4.4.4.9
    PW State               : up
    Local VC Label         : 100
    Remote VC Label        : 200
    Remote Control Word    : disable
    PW Type                : MEHVPLS
    Tunnel ID              : 0x0000000001004c4b44 
    Broadcast Tunnel ID    : --
    Broad BackupTunnel ID  : --
    Ckey                   : 2
    Nkey                   : 1358954645
    Main PW Token          : 0x0
    Slave PW Token         : 0x0
    Tnl Type               : ldp
    OutInterface           : 
    Backup OutInterface    : --
    Stp Enable             : 0
    Mac Flapping           : 0
    PW Last Up Time        : 2015/05/30 17:34:22
    PW Total Up Time       : 0 days, 0 hours, 3 minutes, 26 seconds

Run the display vsi mac-withdraw loop-detect command. If MAC Withdraw loop detection is configured and a loop exists, the command output shows MAC Withdraw loop information.

<HUAWEI> display vsi mac-withdraw loop-detect
Total number of vsi detect loop is 2.
Support max hop 255.

Vsi name        : VSI1
Last loop type  : detect loop
Send peer       : 5.5.5.5
Receive peer    : 2.2.2.2
Last loop time  : 2012/10/26 11:35:59

Vsi name        : VSI2
Last loop type  : exceed max hop
Send peer       : 5.5.5.5
Receive peer    : 3.3.3.3
Last loop time  : 2012/10/26 11:35:59
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 27627

Downloads: 53

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next