No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Configuring the Revertive Switchover

(Optional) Configuring the Revertive Switchover

The revertive switching policies can be classified into three modes: immediate revertive mode, delayed revertive mode, and non-revertive mode.

Context

When primary and secondary PWs are configured, if the primary PW fails, traffic is switched to the secondary PW to prevent traffic interruption. If the primary PW recovers, traffic is by default switched back to the primary PW after 30s. To flexibly adjust the switching time, configure a revertive switching policy.

When CEs are connected to PEs asymmetrically, do as follows on the PE (where traffic is switched) to which a CE is connected through a single link:

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The AC interface view is displayed.

  3. Run mpls l2vpn reroute { { delay delay-time | immediately } [ resume resume-time ] | never }

    The revertive switchover policy is configured.

    The types of the revertive switchover on PEs are as follows:

    • Immediate revertive switchover: The local PE immediately switches traffic to the primary PW and notifies the fault to the remote PE of the secondary PW. The PE notifies the rectification of the fault to the remote PE of the secondary PW after the period of resume-time.

    • Delayed revertive switchover: The PE switches traffic to the primary PW after the period of delay-time.

    • None revertive switchover: The PE does not switch traffic to the primary PW until the secondary PW is faulty.

    For an asymmetric networking, in which ACs are of the Ethernet type, note the following:

    • If the remote shutdown function is configured on the interface of a PE that connects a CE, you are recommended not to use the policy of immediate revertive switchover, which may lead to network flapping and traffic loss. On the other hand, you can use the policy of delayed revertive switchover to set delay-time equal to or more than 30 seconds.

    • If the Ethernet OAM function is configured on the interface of a PE that connects a CE, and a revertive switchover policy is also configured, you cannot set resume-time to be 0 seconds, but be equal to or longer than one second.

  4. Run commit

    The configuration is committed.

Follow-up Procedure

Run the manual-set pw-ac-fault command to simulates a PW fault to check whether a primary/secondary PW switchover is performed or not. The result is saved in the log file.

Run the manual-set pw-ac-fault command on the AC interface of the primary PW, the following situations occur:

  • The status of the primary PW is Down.

  • VC status of the primary PW is InActive, and that of the secondary PW is Active.

  • L2VPN data is switched to the secondary PW.

Run the undo manual-set pw-ac-fault command on the AC interface of the primary PW to rectify the fault on the PW, the following situations occur:

  • The status of the primary PW is up.

  • VC status of the primary PW is Active, and VC status of the secondary PW is InActive.

  • L2VPN data is switched to the primary PW.

Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 36828

Downloads: 61

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next