No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a Local VPLS Connection

Configuring a Local VPLS Connection

This section describes how to configure a local VPLS connection for two CEs connecting to the same PE to communicate.

Usage Scenario

If two CEs connect to the same PE, you can establish a local VPLS connection between the two CEs for them to communicate. In this situation, the PE functions similar to a Layer 2 switch to directly transmit packets without using any public network tunnel.

Pre-configuration Tasks

Before configuring a local VPLS connection, complete the following tasks:

  • Configure the encapsulation types of PE interfaces connecting to CEs.
  • Configure basic MPLS functions on the PE.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run mpls l2vpn

    MPLS L2VPN is enabled.

  3. Run quit

    Return to the system view.

  4. Run vsi [ static ]

    A VSI is configured, and the VSI view is displayed.

  5. Run pwsignal ldp

    LDP is configured as the signaling type of the VSI.

  6. Run vsi-id

    An ID is configured for the VSI.

  7. Run mac-learning disable

    MAC address learning is disabled.

  8. Run p2p-vsi enable

    A local VPLS connection is configured.

  9. Run commit

    The configuration is committed.

Checking the Configurations

After configuring the local VPLS connection, run the following commands to check the configurations:
  • Run the display vsi [ name vsi-name ] [ verbose ] command to check VSI information.
  • Run the display vsi services { vsi-name | all | interface interface-type interface-number | vlan vlan-id } command to check AC interfaces bound to the VSI.

Run the display vsi verbose command. The command output shows that the local VPLS connection is Up.

<HUAWEI> display vsi verbose
 ***VSI Name               : abc
    Work Mode              : normal
    Administrator VSI      : no
    Isolate Spoken         : disable
    VSI Index              : 6
    PW Signaling           : ldp
    Member Discovery Style : --
    Bridge-domain Mode     : disable
    PW MAC Learn Style     : unqualify
    Encapsulation Type     : vlan
    MTU                    : 1500
    Diffserv Mode          : uniform
    Service Class          : --
    Color                  : --
    DomainId               : 255
    Domain Name            :
    Ignore AcState         : disable
    P2P VSI               : disable

    Multicast Fast Swicth  : disable
    Create Time            : 0 days, 0 hours, 2 minutes, 38 seconds
    VSI State             : up
    Resource Status        : --

    VSI ID                 : 11

    Interface Name         : GigabitEthernet0/1/0
    State                  : up
    Access Port            : false
    Last Up Time           : 2015/06/17 09:20:24
    Total Up Time          : 0 days, 0 hours, 0 minutes, 16 seconds
    Interface Name         : GigabitEthernet0/1/1
    State                  : up
    Access Port            : false
    Last Up Time           : 2015/06/17 09:20:24
    Total Up Time          : 0 days, 0 hours, 0 minutes, 16 seconds
 

Run the display vsi services vsi-name command. The command output shows AC interfaces bound to the VSI.

<HUAWEI> display vsi services abc
Total: 2
Code: AS(Admin Status), PS(Physical Status)
--------------------------------------------------------------------------------
Interface/Bridge-domain             Vsi Name                        AS    PS
--------------------------------------------------------------------------------
GigabitEthernet0/1/0                abc                             up    up
GigabitEthernet0/1/1                abc                             up    up
--------------------------------------------------------------------------------
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 27767

Downloads: 53

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next