No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring VPNv4 FRR

Configuring VPNv4 FRR

In an H-VPN scenario in which VPNv4 FRR is configured, if the primary LSP between an ASBR or SPE and its next hop is unreachable, traffic quickly switches to the secondary LSP.

Usage Scenario

In an H-VPN scenario in which VPNv4 FRR is configured on an SPE, the SPE immediately switches VPN services to the standby link if the active link fails.

Figure 5-17 VPNv4 FRR

Pre-configuration Tasks

Before you configure VPNv4 FRR, complete the following tasks:

  • Configure a routing protocol on NEs for them to communicate.

  • Configure two unequal-cost routes between the SPE and remote PE.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run bgp as-number

    The BGP view is displayed.

  3. Run ipv4-family vpnv4

    The BGP-VPNv4 address family view is displayed.

  4. Run auto-frr

    VPNv4 FRR is enabled.

  5. Run bestroute nexthop-resolved tunnel [ inherit-ip-cost ]

    A VPNv4 route is configured to participate in route selection only when its next hop is iterated to a tunnel. This configuration ensures that packets are not lost during traffic switchback.

  6. (Optional) Run route-select delay delay-value

    A delay for selecting a route to the intermediate device on the primary path is configured. After the primary path recovers, an appropriate delay ensures that traffic switches back to the primary path after the intermediate device completes refreshing forwarding entries.

    The delay-value value is an integer ranging from 0 to 3600, in seconds. The default delay-value value is 0, indicating that the device on which FRR is configured selects a route to the intermediate device on the primary path without a delay.

  7. Run commit

    The configuration is committed.

Checking the Configurations

Run the display mpls lsp include ip-address mask-length verbose command to check the index and label of the backup LSP to which the VPNv4 route is iterated.

<HUAWEI> display mpls lsp include 6.6.6.9 32 verbose
-------------------------------------------------------------------------------
                 LSP Information: L3VPN  LSP
-------------------------------------------------------------------------------
  No                  :  0
  VrfIndex            :  ASBR LSP
  RD Value            :  100:1
  Fec                 :  10.10.10.10/32
  Nexthop             :  5.5.5.5
  In-Label            :  33
  Out-Label           :  23
  In-Interface        :  ------
  Out-Interface       :  ------
  LspIndex            :  33
  Type                :  Primary
  OutSegmentIndex     :  ------
  LsrType             :  Transit
  Outgoing TunnelID   :  0x4c4b64
  Label Operation     :  SWAP
  Mpls-Mtu            :  ------
  LspAge              :  ------

  No                  :  1
  VrfIndex            :  ASBR LSP
  RD Value            :  100:1
  Fec                 :  10.10.10.10/32
  Nexthop             :  6.6.6.6
  In-Label            :  33
  Out-Label           :  23
  In-Interface        :  ------
  Out-Interface       :  ------
  LspIndex            :  33
  Type               :  Backup
  OutSegmentIndex     :  ------
  LsrType             :  Transit
  Outgoing TunnelID   :  0x4c4b62
  Label Operation     :  SWAP
  Mpls-Mtu            :  ------
  LspAge              :  ------ 
Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 31812

Downloads: 57

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next