No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN 01

NE05E and NE08E V300R003C10SPC500

This is NE05E and NE08E V300R003C10SPC500 Configuration Guide - VPN
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a PW

Configuring a PW

LDP PWs can be configured in Hierarchical Virtual Private LAN Service (HVPLS) or (Virtual Private LAN Service) VPLS accessing Virtual Private Wire Service (VPWS) networking scenarios.

Context

The service type determines which networking mode to use:

  • HVPLS is best suited for multicast services.
  • VPLS accessing VPWS is best suited for unicast services.

Procedure

  • Configure a PW in HVPLS networking scenarios.

    For details, see Configuring LDP HVPLS.

    1. Run system-view

      The system view is displayed.

    2. Run vsi vsi-name static

      A VSI is created, and the static member discovery mode is specified.

    3. Run pwsignal ldp

      LDP is configured as the PW signaling protocol, and the VSI-LDP view is displayed.

    4. Run vsi-id vsi-id

      A VSI ID is configured.

    5. Run the following commands to configure VSI peers so that PWs can be established:

      • To specify an SPE as the peer of a UPE or to specify an NPE as the peer of an SPE, run the peer (VSI-LDP view) peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ] command.
      • To specify a UPE as the peer of an SPE, run the peer (VSI-LDP view) peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ] upe command.

      From the perspective of a UPE, the PW between itself and an SPE is a hub PW; from the perspective of an SPE, the PW between itself and the UPE is a spoke PW.

    6. Run quit

      Return to the VSI view.

    7. Run quit

      Return to the system view.

    8. Run interface interface-type interface-number

      The AC interface view is displayed.

      This command must be run on the UPEs and NPEs, but is not required on the SPEs. In HVPLS scenarios, a UPE's AC interfaces are Ethernet interfaces, and an NPE's AC interfaces are Eth-Trunk sub-interfaces.

    9. Run vlan-type dot1q vlan-id [ high-vid ]

      The VLAN encapsulation type is configured for the AC interface.

    10. Run l2 binding vsi vsi-name

      The AC interface is bound to the VSI.

  • Configure a PW in VPLS accessing VPWS networking scenarios.

    # Configure a UPE. The configuration procedure is similar to that in HVPLS scenarios. For details, see Configuring HVPLS.

    # Configure NPEs.

    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The AC interface view is displayed.

    3. Run mpls l2vc { ip-address | pw-template pw-template-name } * vc-id [ tunnel-policy policy-name | [ control-word | no-control-word ] | [ raw | tagged ] | access-port | ignore-standby-state ] *

      A dynamic PW is configured on the NPE to connect to the VPLS network on the UPE.

    4. (Optional) Run mpls l2vc { ip-address | pw-template pw-template-name } * vc-id [ tunnel-policy policy-name | [ control-word | no-control-word ] | [ raw | tagged ] | access-port | ignore-standby-state ] * | bypass ]

      A bypass PW is established between NPEs.

      To implement VPLS PW redundancy in master/slave mode, you must configure a bypass PW.

    5. Run commit

      The configuration is committed.

Translation
Download
Updated: 2019-01-14

Document ID: EDOC1100058925

Views: 28105

Downloads: 53

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next