No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Configuration Guide - IP Routing 01

This is ME60 V800R010C10SPC500 Configuration Guide - IP Routing
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Basic RIPng Functions

Example for Configuring Basic RIPng Functions

This section describes how to configure basic RIPng functions.

Networking Requirements

In Figure 8-2, it is required that RIPng be enabled on all interfaces of Device A, Device B, Device C, and Device D and that the ME devices communicate through RIPng.

Figure 8-2 Configuring basic RIPng functions
NOTE:

Interface 1 through 3 in this example are GE 1/0/0, GE 2/0/0 and GE 3/0/0, respectively.


Configuration Notes

When configuring basic RIPng functions, note the following rules:

  • RIPng takes effect only after IPv6 is enabled on interfaces.

  • If a RIPng process is bound to a VPN instance, the interfaces that run this RIPng process are also bound to the VPN instance.

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure IPv6 addresses for interfaces to ensure that neighboring nodes are reachable at the network layer.

  2. Enable RIPng and configure basic RIPng functions on each ME device.

Data Preparation

To complete the configuration, you need IPv6 addresses of interfaces.

Procedure

  1. Configure IPv6 addresses for interfaces. For configuration details, see Configuration Files in this section.
  2. Configure basic RIPng functions.

    # Configure Device A.

    [~DeviceA] ipv6
    [*DeviceA] ripng 1
    [*DeviceA-ripng-1] commit
    [~DeviceA-ripng-1] quit
    [~DeviceA] interface gigabitethernet1/0/0
    [~DeviceA-GigabitEthernet1/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet1/0/0] ipv6 address 2001:db8:1::1/96
    [*DeviceA-GigabitEthernet1/0/0] ripng 1 enable
    [*DeviceA-ripng-1] commit
    [~DeviceA-ripng-1] quit

    # Configure Device B.

    [~DeviceA] ipv6
    [*DeviceB] ripng 1
    [*DeviceA-ripng-1] commit
    [~DeviceA-ripng-1] quit
    [~DeviceA] interface gigabitethernet1/0/0
    [~DeviceA-GigabitEthernet1/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet1/0/0] ipv6 address 2001:db8:1::2/96
    [*DeviceA-GigabitEthernet1/0/0] ripng 1 enable
    [*DeviceA-GigabitEthernet1/0/0] commit
    [~DeviceA-GigabitEthernet1/0/0] quit
    [~DeviceA] interface gigabitethernet2/0/0
    [~DeviceA-GigabitEthernet2/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet2/0/0] ipv6 address 2001:db8:2::1/96
    [*DeviceA-GigabitEthernet2/0/0] ripng 1 enable
    [*DeviceA-GigabitEthernet2/0/0] commit
    [~DeviceA-GigabitEthernet2/0/0] quit
    [~DeviceA] interface gigabitethernet3/0/0
    [~DeviceA-GigabitEthernet3/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet3/0/0] ipv6 address 2001:db8:3::1/96
    [*DeviceA-GigabitEthernet3/0/0] ripng 1 enable
    [*DeviceA-GigabitEthernet2/0/0] commit
    [~DeviceA-GigabitEthernet3/0/0] quit

    # Configure Device C.

    [~DeviceA] ipv6
    [*DeviceC] ripng 1
    [*DeviceA-ripng-1] commit
    [~DeviceA-ripng-1] quit
    [~DeviceA] interface gigabitethernet2/0/0
    [~DeviceA-GigabitEthernet2/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet2/0/0] ipv6 address 2001:db8:2::2/96
    [*DeviceA-GigabitEthernet2/0/0] ripng 1 enable
    [*DeviceA-GigabitEthernet2/0/0] commit
    [~DeviceA-GigabitEthernet2/0/0] quit

    # Configure Device D.

    [~DeviceA] ipv6
    [*DeviceD] ripng 1
    [*DeviceA-ripng-1] commit
    [~DeviceA-ripng-1] quit
    [~DeviceA] interface gigabitethernet3/0/0
    [~DeviceA-GigabitEthernet3/0/0] ipv6 enable
    [*DeviceA-GigabitEthernet3/0/0] ipv6 address 2001:db8:3::2/96
    [*DeviceA-GigabitEthernet3/0/0] ripng 1 enable
    [*DeviceA-GigabitEthernet3/0/0] commit
    [~DeviceA-GigabitEthernet3/0/0] quit

  3. Verify the configuration.

    # View RIPng neighbors of Device A.

    [~DeviceA] display ripng 1 neighbor
    Neighbor : FE80::A0A:201:1 GigabitEthernet1/0/0
    Protocol : RIPNG

    The command output shows that Device A has established the neighbor relationship with other devices on the network.

    # View RIPng routing information of Device B.

    [~DeviceB] display ripng 1 route
    Route Flags: A - Aging, S - Suppressed, G - Garbage-collect
    -----------------------------------------------------------
    Peer FE80::F54C:0:9FDB:1  on GigabitEthernet1/0/0
    Dest 2001:DB8:1::1/96,
        via FE80::F54C:0:9FDB:1, cost  1, tag 0, A, 3 Sec
    Peer FE80::D472:0:3C23:1  on GigabitEthernet2/0/0
    Dest 2001:DB8:2::2/96,
        via FE80::D472:0:3C23:1, cost  1, tag 0, A, 4 Sec
    Peer FE80::D472:0:3C23:1  on GigabitEthernet3/0/0
    Dest 2001:DB8:3::2/96,
        via FE80::D472:0:3C23:1, cost  1, tag 0, A, 4 Sec

    The command output shows that Device B has learned routing information on the network.

Configuration Files

  • Device A configuration file

    #
    sysname DeviceA
    #
    ipv6
    #
    interface GigabitEthernet1/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:1::1/96
     ripng 1 enable
    #
    ripng 1
    #
    return
  • Device B configuration file

    #
    sysname DeviceB
    #
    ipv6
    #
    interface GigabitEthernet1/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:1::2/96
     ripng 1 enable
    #
    interface GigabitEthernet2/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:2::1/96
     ripng 1 enable
    #
    interface GigabitEthernet3/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:3::1/96
     ripng 1 enable
    #
    ripng 1
    #
    return
  • Device C configuration file

    #
    sysname DeviceC
    #
    ipv6
    #
    interface GigabitEthernet2/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:2::2/96
     ripng 1 enable
    #
    ripng 1
    #
    return
  • Device D configuration file

    #
    sysname DeviceD
    #
    ipv6
    #
    interface GigabitEthernet3/0/0
     undo shutdown
     ipv6 enable
     ipv6 address 2001:db8:3::2/96
     ripng 1 enable
    #
    ripng 1
    #
    return
Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059437

Views: 20333

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next