No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Configuration Guide - IP Routing 01

This is ME60 V800R010C10SPC500 Configuration Guide - IP Routing
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Dynamic BFD for RIP

Configuring Dynamic BFD for RIP

On a network that runs high-rate data services, dynamic BFD for RIP can be configured to quickly detect and respond to network faults.

Usage Scenario

RIP-capable devices detect neighbor status by exchanging Update packets periodically. By default, a local device can detect a link failure 180s after the link fails. During this period, carriers or users may lose a large number of packets.

BFD can detect a fault (if any) within milliseconds and notify the RIP module of the fault. BFD for RIP can speed up fault detection and route convergence, which improves network reliability.

In BFD for RIP, BFD session establishment is triggered by RIP. When establishing a neighbor relationship, RIP will send detection parameters of the neighbor to BFD. Then, a BFD session will be established based on these detection parameters. If a link fault occurs, the local RIP process will receive a neighbor unreachable message within milliseconds. Then, the local RIP device will delete routing entries in which the neighbor relationship is Down and use the backup path to transmit messages.

Either of the following methods can be used to configure BFD for RIP:

Pre-configuration Tasks

Before configuring BFD for RIP, complete the following tasks:

Procedure

  • Enable BFD in a RIP process.
    1. Run system-view

      The system view is displayed.

    2. Run bfd

      BFD is enabled globally.

    3. Run quit

      Return to the system view.

    4. Run rip process-id

      The RIP view is displayed.

    5. Run bfd all-interfaces enable (RIP)

      BFD is enabled in the RIP process to establish BFD sessions.

      If BFD is enabled globally, RIP will use default BFD parameters to establish BFD sessions on all the interfaces where RIP neighbor relationships are Up.

    6. (Optional) Run bfd all-interfaces { min-rx-interval min-receive-value | min-tx-interval min-transmit-value | detect-multiplier detect-multiplier-value } *

      The values of BFD parameters used to establish the BFD session are set.

      Configure BFD parameter values based on the reliability requirements of the live network.
      • If the live network requires high reliability, reduce the interval at which BFD packets are sent.
      • If the live network requires low reliability, increase the interval at which BFD packets are sent.

      BFD detection intervals are calculated as follows:

      • Effective local interval at which BFD packets are sent = MAX { Configured local interval at which BFD packets are sent, Configured remote interval at which BFD packets are received }
      • Effective local interval at which BFD packets are received = MAX { Configured remote interval at which BFD packets are sent, Configured local interval at which BFD packets are received }
      • Effective local detection interval = Effective local interval at which BFD packets are received x Configured remote detection multiplier

      Running the bfd all-interfaces command changes BFD session parameters on all RIP interfaces. The default detection multiplier and interval at which BFD packets are sent are recommended.

    7. (Optional) Perform the following operations to prevent an interface in the RIP process from establishing a BFD session:

      • Run the quit command to return to the system view.
      • Run the interface interface-type interface-number command to enter the view of a specified interface.
      • Run the rip bfd block command to prevent the interface from establishing a BFD session.

    8. Run commit

      The configuration is committed.

  • Enable BFD on a RIP interface.
    1. Run system-view

      The system view is displayed.

    2. Run bfd

      BFD is enabled globally.

    3. Run quit

      Return to the system view.

    4. Run interface interface-type interface-number

      The view of the specified interface is displayed.

    5. Run rip bfd enable

      BFD is enabled on the interface to establish a BFD session.

    6. (Optional) Run rip bfd { min-rx-interval min-receive-value | min-tx-interval min-transmit-value | detect-multiplier detect-multiplier-value } *

      The values of BFD parameters used to establish the BFD session are set.

    7. Run commit

      The configuration is committed.

Checking the Configurations

After enabling BFD for RIP at both ends of a link, run the display rip bfd session { interface interface-type interface-number | neighbor-id | all } command. The following command output shows that the BFDState field on the local router is Up.

<HUAWEI> display rip 1 bfd session all
 LocalIp      :10.1.0.1         RemoteIp  :10.1.0.2         BFDState :Up       
 TX           :1000             RX        :1000             Multiplier:3       
 BFD Local Dis:8192             Interface :GigabitEthernet1/0/0                    
 DiagnosticInfo: No diagnostic information                               
 LocalIp      :20.1.0.1         RemoteIp  :20.1.0.2         BFDState :Up       
 TX           :1000             RX        :1000             Multiplier:3       
 BFD Local Dis:8193             Interface :GigabitEthernet1/0/1                    
 DiagnosticInfo: No diagnostic information                               
Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059437

Views: 22385

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next