No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Configuration Guide - IP Routing 01

This is ME60 V800R010C10SPC500 Configuration Guide - IP Routing
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IS-IS Neighbor Relationship Flapping Suppression

Configuring IS-IS Neighbor Relationship Flapping Suppression

IS-IS neighbor relationship flapping suppression works by delaying IS-IS neighbor relationship reestablishment or setting the link cost to the maximum value.

Usage Scenario

If an interface carrying IS-IS services alternates between Up and Down, IS-IS neighbor relationship flapping occurs on the interface. During the flapping, IS-IS reestablishes the neighbor relationship and recalculates routes. In this process, a large number of packets are exchanged, adversely affecting neighbor relationship stability, IS-IS services, and other IS-IS-dependent services, such as LDP and BGP. IS-IS neighbor relationship flapping suppression can address this problem by delaying IS-IS neighbor relationship reestablishment or preventing service traffic from passing through flapping links.

NOTE:
The following steps are optional, choose them as required.

Pre-configuration Tasks

Before configuring IS-IS neighbor relationship flapping suppression, complete the following tasks:

Procedure

  1. Run system-view

    The system view is displayed.

    By default, IS-IS neighbor relationship flapping suppression is enabled globally. To disable this function globally, run the suppress-flapping peer disable command.

  2. Run interface interface-type interface-number

    The interface view is displayed.

    By default, IS-IS neighbor relationship flapping suppression is enabled on all interfaces in the same IS-IS process. To disable the function from one of the interfaces, run the isis suppress-flapping peer disable command.

  3. Run isis suppress-flapping peer hold-down interval

    The Hold-down mode is configured, and its duration is set.

    Flapping suppression works in either Hold-down or Hold-max-cost mode.

    • Hold-down mode: In the case of frequent flooding and topology changes during neighbor relationship establishment, interfaces prevent neighbor relationship reestablishment during Hold-down suppression, which minimizes synchronization attempts and packet exchanges.
    • Hold-max-cost mode: If the traffic forwarding path changes frequently, interfaces use the maximum value (16777214 for the wide mode and 63 for the narrow mode) as the cost of the flapping link during Hold-max-cost suppression, which prevents traffic from passing through the flapping link.

    Flapping suppression can also work first in Hold-down mode and then in Hold-max-cost mode.

    lili

    To disable this mode, run the isis suppress-flapping peer hold-max-cost disable command.

  4. Run isis suppress-flapping peer { detecting-interval detecting-interval | threshold threshold | resume-interval resume-interval } *

    Detection parameters are configured for IS-IS neighbor relationship flapping suppression.

    Each IS-IS interface on which IS-IS neighbor relationship flapping suppression is enabled starts a flapping counter. If the interval between two successive neighbor status changes from Full to a non-Full state is shorter than detecting-interval, a valid flapping_event is recorded, and the flapping_count increases by 1. When the flapping_count reaches or exceeds threshold, flapping suppression takes effect. If the interval between two successive neighbor status changes from Full to a non-Full state is longer than resume-interval, the flapping_count is reset.

    NOTE:

    The value of resume-interval must be greater than that of detecting-interval.

    Using the default detection parameters is recommended.

  5. Run quit

    The system view is displayed.

  6. Run quit

    The user view is displayed.

  7. Run reset isis process-id suppress-flapping peer [ interface interface-type interface-number ] [ notify-peer ]

    Interfaces are forced to exit from IS-IS neighbor relationship flapping suppression.

    Interfaces exit from flapping suppression in the following scenarios:
    • The suppression timer expires.
    • The corresponding IS-IS process is reset.
    • An IS-IS neighbor is reset using the reset isis peer command.
    • IS-IS neighbor relationship flapping suppression is disabled globally using the suppress-flapping peer disable (IS-IS) command in the IS-IS view.
    • The reset isis suppress-flapping peer command is run.
    • Suppression is aborted forcibly using the reset isis process-id suppress-flapping peer [ interface interface-type interface-number ] notify-peer command on the remote device.

  8. Run commit

    The configuration is committed.

Checking the Configurations

Run the display isis [ process-id ] interface interface-type interface-number verbose command to check the status of IS-IS neighbor relationship flapping suppression.

<HUAWEI> display isis interface verbose
                       Interface information for ISIS(1)
                       ---------------------------------
 Interface         Id      IPV4.State          IPV6.State      MTU  Type  DIS
 GE1/0/0           002         Up          Mtu:Up/Lnk:Up/IP:Up 1497 L1/L2 Yes/Yes
  Circuit MT State            : Standard  
  Description                 : HUAWEI, Quidway Series, GigabitEthernet1/0/0 Interface
  SNPA Address                : 3800-1003-0002
  IP Address                  : 192.168.2.2
  IPV6 Link Local Address     : 
  IPV6 Global Address(es)     : 
  Csnp Timer Value            :  L1    10  L2    10
  Hello Timer Value           :  L1    10  L2    10
  DIS Hello Timer Value       :  L1     3  L2     3
  Hello Multiplier Value      :  L1     3  L2     3
  LSP-Throttle Timer          :  L12    50 <50ms>
  Cost                        :  L1    10  L2    10
  Ipv6 Cost                   :  L1     0  L2     0
  Priority                    :  L1    64  L2    64
  Retransmit Timer Value      :  L1     5  L2     5
  Bandwidth-Value             :  Low  100000000  High          0
  Static Bfd                  :  NO
  Dynamic Bfd                 :  YES
  Static IPv6 Bfd             :  NO
  Dynamic IPv6 Bfd            :  NO
  Suppress Base               :  NO
  IPv6 Suppress Base          :  NO

  Extended-Circuit-Id Value   :  0000000000
  Circuit State               :  OSI:UP   / IP:UP   / MTU:UP   / IPBorrow:UP   /
                                 BandWidth:UP   / IsEnable:UP   / Interface:UP  
  Circuit Ipv6 State          :  OSI:UP   / IP:UP   / MTU:UP   / IPBorrow:UP   /
                                 BandWidth:UP   / IsEnable:DOWN / Interface:UP  
  Suppress flapping peer      :  Hold-down(start: UTC 10:20:30, remain-interval: 7)  

Suppress flapping peer in the command output indicates the current suppression mode (Hold-down), time when the flapping suppression started, and the remaining time of the flapping suppression.

Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059437

Views: 20845

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next