No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Feature Description - WAN Access 01

This is ME60 V800R010C10SPC500 Feature Description - WAN Access
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
OSPFv3 Neighbor Relationship Flapping Suppression

OSPFv3 Neighbor Relationship Flapping Suppression

OSPFv3 neighbor relationship flapping suppression works by delaying OSPFv3 neighbor relationship reestablishment or setting the link cost to the maximum value (65535).

Background

If the status of an interface carrying OSPFv3 services alternates between Up and Down, OSPFv3 neighbor relationship flapping occurs on the interface. During the flapping, OSPFv3 frequently sends Hello packets to reestablish the neighbor relationship, synchronizes LSDBs, and recalculates routes. In this process, a large number of packets are exchanged, adversely affecting neighbor relationship stability, OSPFv3 services, and other OSPFv3-dependent services, such as LDP and BGP. OSPFv3 neighbor relationship flapping suppression can address this problem by delaying OSPFv3 neighbor relationship reestablishment or preventing service traffic from passing through flapping links.

Related Concepts

Flapping_event: reported when the status of a neighbor relationship on an interface last changes from Full to a non-Full state. The flapping_event triggers flapping detection.

Flapping_count: number of times flapping has occurred.

Detect-interval: detection interval. The interval is used to determine whether to trigger a valid flapping_event.

Threshold: flapping suppression threshold. When the flapping_count reaches or exceeds threshold, flapping suppression takes effect.

Resume-interval: interval for exiting from OSPFv3 neighbor relationship flapping suppression. If the interval between two successive valid flapping_events is longer than resume-interval, the flapping_count is reset.

Implementation

Flapping detection

Each OSPFv3 interface on which OSPFv3 neighbor relationship flapping suppression is enabled starts a flapping counter. If the interval between two successive neighbor status changes from Full to a non-Full state is shorter than detecting-interval, a valid flapping_event is recorded, and the flapping_count increases by 1. When the flapping_count reaches or exceeds threshold, flapping suppression takes effect. If the interval between two successive neighbor status changes from Full to a non-Full state is longer than resume-interval, the flapping_count is reset.

The detecting-interval, threshold, and resume-interval are configurable.

NOTE:
The value of resume-interval must be greater than that of detecting-interval.
Flapping suppression

Flapping suppression works in either Hold-down or Hold-max-cost mode.

  • Hold-down mode: In the case of frequent flooding and topology changes during neighbor relationship establishment, interfaces prevent neighbor relationships from being reestablished during the suppression period, which minimizes LSDB synchronization attempts and packet exchanges.
  • Hold-max-cost mode: If the traffic forwarding path changes frequently, interfaces use 65535 as the cost of the flapping link during Hold-max-cost suppression, which prevents traffic from passing through the flapping link.

Flapping suppression can also work first in Hold-down mode and then in Hold-max-cost mode.

By default, the Hold-max-cost mode takes effect. The mode and suppression duration can be changed manually.

If an attack causes frequent neighbor relationship flapping, Hold-down mode can minimize the impact of the attack.

NOTE:
When an interface enters the flapping suppression state, all neighbor relationships on the interface enter the state accordingly.
Exiting from flapping suppression

Interfaces exit from flapping suppression in the following scenarios:

  • The suppression timer expires.
  • The corresponding OSPFv3 process is reset.
  • An OSPF neighbor is reset.
  • A command is run to exit from flapping suppression.

Typical Scenarios

Basic scenario

In Figure 7-11, the traffic forwarding path is Device A -> Device B -> Device C -> Device E before a link failure occurs. After the link between Device B and Device C fails, the forwarding path switches to Device A -> Device B -> Device D -> Device E. If the neighbor relationship between Device B and Device C frequently flaps at the early stage of the path switchover, the forwarding path will be switched frequently, causing traffic loss and affecting network stability. If the neighbor relationship flapping meets suppression conditions, flapping suppression takes effect.

  • If flapping suppression works in Hold-down mode, the neighbor relationship between Device B and Device C is prevented from being reestablished during the suppression period, in which traffic is forwarded along the path Device A -> Device B -> Device D -> Device E.
  • If flapping suppression works in Hold-max-cost mode, 65535 is used as the cost of the link between Device B and Device C during the suppression period, and traffic is forwarded along the path Device A -> Device B -> Device D -> Device E.
Figure 7-11 Flapping suppression in a basic scenario
Single-forwarding path scenario

When only one forwarding path exists on the network, the flapping of the neighbor relationship between any two devices on the path will interrupt traffic forwarding. In Figure 7-12, the traffic forwarding path is Device A -> Device B -> Device C -> Device E. If the neighbor relationship between Device B and Device C flaps, and the flapping meets suppression conditions, flapping suppression takes effect. However, if the neighbor relationship between Device B and Device C is prevented from being reestablished, the whole network will be divided. Therefore, Hold-max-cost mode (rather than Hold-down mode) is recommended. If flapping suppression works in Hold-max-cost mode, 65535 is used as the cost of the link between Device B and Device C during the suppression period. After the network stabilizes and the suppression timer expires, the link is restored.

NOTE:

By default, the Hold-max-cost mode takes effect.

Figure 7-12 Flapping suppression in a single-forwarding path scenario
Broadcast scenario

In Figure 7-13, four devices are deployed on the same broadcast network using switches, and the devices are broadcast network neighbors. If Device C flaps due to a link failure, and Device A and Device B were deployed at different time (Device A was deployed earlier for example) or the flapping suppression parameters on Device A and Device B are different, Device A first detects the flapping and suppresses Device C. Consequently, the Hello packets sent by Device A do not carry Device C's router ID. However, Device B has not detected the flapping yet and still considers Device C a valid node. As a result, the DR candidates identified by Device A are Device B and Device D, whereas the DR candidates identified by Device B are Device A, Device C, and Device D. Different DR candidates result in a different DR election result, which may lead to route calculation errors. To prevent this problem in scenarios where an interface has multiple neighbors, such as on a broadcast, P2MP, or NBMA network, all neighbors on the interface are suppressed when the status of a neighbor relationship last changes to ExStart or Down. Specifically, if Device C flaps, Device A, Device B, and Device D on the broadcast network are all suppressed. After the network stabilizes and the suppression timer expires, Device A, Device B, and Device D are restored to normal status.

Figure 7-13 Flapping suppression on a broadcast network
Multi-area scenario

In Figure 7-14, Device A, Device B, Device C, Device E, and Device F are connected in area 1, and Device B, Device D, and Device E are connected in backbone area 0. Traffic from Device A to Device F is preferentially forwarded along an intra-area route, and the forwarding path is Device A -> Device B -> Device C -> Device E -> Device F. When the neighbor relationship between Device B and Device C flaps and the flapping meets suppression conditions, flapping suppression takes effect in the default mode (Hold-max-cost). Consequently, 65535 is used as the cost of the link between Device B and Device C. However, the forwarding path remains unchanged because intra-area routes take precedence over inter-area routes during route selection according to OSPFv3 route selection rules. To prevent traffic loss in multi-area scenarios, configure Hold-down mode to prevent the neighbor relationship between Device B and Device C from being reestablished during the suppression period. During this period, traffic is forwarded along the path Device A -> Device B -> Device D -> Device E -> Device F.

NOTE:

By default, the Hold-max-cost mode takes effect. The mode can be changed to Hold-down manually.

Figure 7-14 Flapping suppression in a multi-area scenario
Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059473

Views: 14577

Downloads: 10

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next