No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Feature Description - WAN Access 01

This is ME60 V800R010C10SPC500 Feature Description - WAN Access

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Association between LDP and Static Routes

Association between LDP and Static Routes

Background

If a backup path exists between LSRs, packet loss may occur due to status inconsistency between static routes and LDP sessions. To solve this problem, you can configure association between LDP and static routes.

Typical Networking

Figure 3-6 shows the typical networking of association between LDP and static routes. LSRA and LSRD interwork through static routes. Primary and secondary static routes are deployed on LSRA, with the next-hop devices being LSRB and LSRC, respectively. Primary and secondary LDP LSPs are established based on the static routes. The primary LSP uses Link A, and the secondary LSP uses Link B. In normal cases, Link A is preferred. Association between LDP and static routes in switchover and switchback scenarios is described as follows.

Figure 3-6 Networking of LSP switching scenario where association between LDP and static routes is configured

Switchover scenario

In the switchover scenario, traffic of the primary static route is not switched to the secondary link when the LDP session on the primary link fails (not because of a link fault). As a result, traffic on the LSP over the primary link is interrupted.

After an LDP session is established, LSP traffic travels along the primary link, Link A (LSRA → LSRB → LSRD). If the LDP session between LSRA and LSRB is interrupted, traffic of the primary LSP is switched immediately to the secondary link, Link B (LSRA → LSRC → LSRD). However, because the link between LSRA and LSRB is normal, traffic of the primary static route is not switched to the secondary link. The asynchronous state between LDP and the primary static route causes an LSP traffic interruption.

If association between LDP and static routes is enabled, traffic is automatically switched to the secondary link when the LDP session goes Down, ensuring uninterrupted traffic forwarding.

Switchback scenario

In the switchback scenario, when the primary link recovers from a fault, the traffic of the primary static route is switched back to Link A earlier than the traffic of the primary LSP because the convergence of static routes is faster than that of LDP LSPs. As a result, the secondary LSP on Link B cannot be used, and the LSP on Link A has not been set up yet. As a result, LSP traffic is interrupted.

If the link between LSRA and LSRB fails, traffic is switched immediately to the secondary link, Link B (LSRA → LSRC → LSRD). After the link between LSRA and LSRB recovers, traffic of the primary static route is immediately switched back to Link A (LSRA → LSRB → LSRD). However, the secondary LSP cannot be used, and the LSP on Link A has not recovered yet. As a result, traffic is interrupted.

If association between LDP and static routes is enabled, the static route on Link A becomes active only when the LDP session on Link A goes Up. In this manner, the states of the primary static route and LSP are asynchronous during the switchback, which prevents traffic loss.

Usage Scenario

Association between LDP and static routes applies to scenarios where a static route backup path exists between LSRs.

Benefits

Association between LDP and static routes ensures state consistency between LDP and static routes, prevents traffic loss, and improves network reliability.

Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059473

Views: 17872

Downloads: 10

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next