No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ME60 V800R010C10SPC500 Hardware Description

This is ME60 V800R010C10SPC500 Hardware Description
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ME60-X16 Main Processing Unit B5(16G Memory)

ME60-X16 Main Processing Unit B5(16G Memory)

Overview

Table 10-68 Board attributes

Attribute

Description

Board name silkscreen

MPUB5

Description

ME60-X16 Main Processing Unit B5(16G Memory)

BOM

03057247

Model

ME0D0MPUB571

Table 10-69 Mapping products and versions

Product

Minimum Version Requirement

ME60-X16

V800R008C10

ME60-X16A

V800R008C10

Appearance



Panel

Table 10-70 Buttons

Name

Description

OFL

Before removing a board, press and hold the OFL button for about 6 seconds until the OFL indicator turns on. Then, you can remove the board.

This button takes effect only on the slave MPU.

RST

When this button is pressed, the board is reset.

Table 10-71 Indicators

Name

Description

OFL (red)

If this indicator is on, you can remove the board.

RUN (green)

Before the board is powered on and registers, this indicator status changes in the following sequence: off > blinks quickly > steady on > blinks quickly > steady on > blinks slowly (0.5 Hz).

After the board is powered on and registers, if this indicator blinks at 0.5 Hz, the system is working properly.

ALM (red)

If this indicator is steady on, an alarm is generated.

If this indicator is off, no alarm is generated.

ACT (green)

If this indicator is steady on, the board functions as the master one.

If this indicator is off, the board functions as the slave one.

Optical interface L/A

Reserved.

MGMT-ETH LINK (green)

If this indicator is steady on, the link is Up.

If this indicator is off, the link is Down.

MGMT-ETH ACT (yellow)

If this indicator is blinking, data is being transmitted and received.

If this indicator is off, no data is being transmitted or received.

Table 10-72 Management interfaces

Interface Name

Interface Type

Connector Type

Description

Cable

FSP0, FSP1

Serial interface

RJ45

Reserved. It functions as an interface for fast chassis switchovers.

-

GE/10GE

GE/10GE

SFP+/SFP

Reserved cascading interface.

-

MGMT-ETH

Ethernet interface (10M/100M/1000M Base-TX autonegotiation)

RJ45

It connects to an NMS and can work in half-duplex or full-duplex mode.

Super category 5 shielded twisted pair

Console

RS-232 serial interface

RJ45

It connects to the console for on-site system configuration. Baud rate: 9600 bit/s (default value), which is configurable.

8-core shielded cable

AUX

RS-232 serial interface

RJ45

It connects to the modem for remote mainteN/Ance by means of dial-up. Baud rate: 9600 bit/s (default value), which is configurable.

8-core shielded cable

CLK/TOD0, CLK/TOD1

External synchronization interface

RJ45

Used to input or output 2-Mbit/s clock signals, 2-MHz clock signals, 1pps+ASCII time signals, or two channels of DCLS time signals.

120-ohm clock cable

CLK/1PPS

External synchronization interface

SMB

Used to input or output 2-Mbit/s clock signals, 2-MHz clock signals, or 1 PPS signals.

75-ohm clock cable

CLK/Serial

External synchronization interface

SMB

Used to input or output 2-Mbit/s clock signals, 2-MHz clock signals, or RS-232 signals.

75-ohm clock cable

Functional Specifications

Table 10-73 Functions and features

Functions and Features

Remarks

Reliability and availability

1:1 backup mode

Technical Specifications

Table 10-74 Board specifications

Item

Specification

Dimensions (H x W x D)

40.1 mm x 399.2 mm x 535.6 mm (1.58 in. x 15.72 in. x 21.09 in.)

Typical power consumption

93.0 W

Typical heat dissipation

301.7 BTU/hour

Weight

4.5 kg (9.92 lb)

Ambient temperature

Long terms: 0 °C to 45 °C (32°F to 113°F) Short terms: -5 °C to 55 °C (23°F to 131°F)

Processing unit

Quad-core 2.0GHz

SDRAM

8 GB x 2

Flash

16 MB

Storage

SSD card:8 GB

Translation
Download
Updated: 2019-01-04

Document ID: EDOC1100059474

Views: 31910

Downloads: 85

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next