No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess 6.5 F5 Configuration Guide 02

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IP Addresses for the VLANs

Configuring IP Addresses for the VLANs

Scenarios

This section describes how to configure the F5 BIG-IP network based on the network planning.

Procedure

  1. In the navigation pane on the left, choose Network > Self IPs.

    The Self IPs page is displayed.

  2. Configure Self IP addresses.

    1. Click Create....
    2. Set the related parameters as planned, as shown in Figure 3-11.
      Figure 3-11 Configuration
      • Name: Enter the disk name.
      • IP Address: Enter an IP address.
      • Netmask: Enter a subnet mask.
      • VLAN/Tunnel: Select the VLAN to which the IP address is bound. All the configured VLAN names are displayed in the drop-down list.
      • Port Lockdown: Generally, retain the default value Allow Default. If VLAN settings are synchronized, you are advised to set Port Lockdown to Allow All.
    3. Click Finished.

  3. Add the data listed in Step 2 in sequence by referring to Step 2.

    Table 3-3 VLAN IP

    Host Name

    Name

    IP Address

    Netmask

    VLAN/Tunnel

    Port Lockdown

    Traffic

    Group

    LB01.test.com

    SELF-EXT

    192.168.201.2

    /24

    VLAN-EXT

    Allow Default

    Traffic-group-local-only(none-floating)

    SELF-EXT-FLOAT

    192.168.201.100

    /24

    VLAN-EXT

    Allow Default

    Traffic-group-local-only(floating)

    SELF-INT

    192.168.202.2

    /24

    VLAN-INT

    Allow Default

    Traffic-group-local-only(none-floating)

    SELF-INT-FLOAT

    192.168.202.100

    /24

    VLAN-INT

    Allow Default

    Traffic-group-local-only(floating)

    SELF-HA

    192.168.204.2

    /24

    VLAN-HA

    Allow Default

    Traffic-group-local-only(none-floating)

    LB02.test.com

    SELF-EXT

    192.168.201.3

    /24

    VLAN-EXT

    Allow Default

    Traffic-group-local-only(none-floating)

    SELF-EXT-FLOAT

    192.168.201.100

    /24

    VLAN-EXT

    Allow Default

    Traffic-group-local-only(floating)

    SELF-INT

    192.168.202.3

    /24

    VLAN-INT

    Allow Default

    Traffic-group-local-only(none-floating)

    SELF-INT-FLOAT

    192.168.202.100

    /24

    VLAN-INT

    Allow Default

    Traffic-group-local-only(floating)

    SELF-HA

    192.168.204.3

    /24

    VLAN-HA

    Allow Default

    Traffic-group-local-only(none-floating)

Download
Updated: 2019-05-30

Document ID: EDOC1100062218

Views: 611

Downloads: 20

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next