No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

HUAWEI Firewall Comprehensive Configuration Examples

This document describes the application scenarios and configuration methods in typical projects of the firewall.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Hot Standby

Configuring Hot Standby

Context

Complete the hot standby configuration according to the figure below.
Figure 9-8  Hot standby networking

Procedure

  1. Configure hot standby.

    # Configure hot standby on FW_A.

    1. Configure a VGMP group to monitor Eth-Trunk1.

      [FW_A] hrp track interface Eth-Trunk 1
    2. Enable the VGMP group state-based OSPF cost adjustment function.

      [FW_A] hrp adjust ospf-cost enable
    3. Specify Eth-Trunk2 as the heartbeat interface and enable hot standby.

      [FW_A] hrp interface Eth-Trunk 2 remote 2.1.1.2
      HRP_M[FW_A] hrp enable

    # Configure hot standby on FW_B.

    1. Configure a VGMP group to track Eth-Trunk1.

      [FW_B] hrp track interface Eth-Trunk 1
    2. Specify FW_B as the standby firewall.

      [FW_B] hrp standby-device
    3. Enable the VGMP group state-based OSPF cost adjustment function.

      [FW_B] hrp adjust ospf-cost enable
    4. Specify Eth-Trunk2 as the heartbeat interface and enable hot standby.

      [FW_B] hrp interface Eth-Trunk 2 remote 2.1.1.1
      HRP_S[FW_B] hrp enable

  2. Configure OSPF.

    # Configure OSPF on FW_A.

    HRP_M[FW_A] router id 1.1.1.1
    HRP_M[FW_A] ospf 1
    HRP_M[FW_A-ospf-1] area 1.1.1.1
    HRP_M[FW_A-ospf-1-area-1.1.1.1] network 1.1.1.1 0.0.0.3
    HRP_M[FW_A-ospf-1-area-1.1.1.1] network 3.1.1.1 0.0.0.3
    HRP_M[FW_A-ospf-1-area-1.1.1.1] quit
    HRP_M[FW_A-ospf-1] quit
    

    # Configure OSPF on FW_B.

    HRP_S[FW_A] router id 5.5.5.1
    HRP_S[FW_A] ospf 1
    HRP_S[FW_A-ospf-1] area 1.1.1.1
    HRP_S[FW_A-ospf-1-area-1.1.1.1] network 5.1.1.1 0.0.0.3
    HRP_S[FW_A-ospf-1-area-1.1.1.1] network 3.1.1.1 0.0.0.3
    HRP_S[FW_A-ospf-1-area-1.1.1.1] quit
    HRP_S[FW_A-ospf-1] quit
    

Translation
Download
Updated: 2019-01-26

Document ID: EDOC1100062972

Views: 16509

Downloads: 710

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next