display ap-group
Function
The display ap-group command displays configuration and reference information about an AP group.
Usage Guidelines
You can run the display ap-group command to view configuration and reference information about an AP group.
Example
# Display information about all AP groups.
<AC6605> display ap-group all
----------------------------------------------------------
Name APs
----------------------------------------------------------
default 1
ap-group1 0
----------------------------------------------------------
Total: 2
Item |
Description |
|---|---|
Name |
Name of an AP group. |
APs |
Number of APs in an AP group. |
# Display information about the AP group default.
<AC6605> display ap-group name default --------------------------------------------------------------------------------------- AP system profile : default Regulatory domain profile : default WIDS profile : default BLE profile : Site code : AP location : UUID : Domain name : AP wired port profile Interface FE0 : default Interface FE1 : default Interface FE2 : default Interface FE3 : default Interface GE0 : default Interface GE1 : default Interface GE2 : default Interface GE3 : default Interface GE4 : default Interface GE5 : default Interface GE6 : default Interface GE7 : default Interface GE8 : default Interface GE9 : default Interface GE10 : default Interface GE11 : default Interface GE12 : default Interface GE13 : default Interface GE14 : default Interface GE15 : default Interface GE16 : default Interface GE17 : default Interface GE18 : default Interface GE19 : default Interface GE20 : default Interface GE21 : default Interface GE22 : default Interface GE23 : default Interface GE24 : default Interface GE25 : default Interface GE26 : default Interface GE27 : default Interface MultiGE0 : default Interface XGE0 : default Interface XGE1 : default Interface XGE2 : default Interface XGE3 : default Interface Eth-trunk0 : default Radio 0 Radio 2.4G profile : default Radio 5G profile : default VAP profile : Mesh profile : WDS profile : Mesh whitelist profile : WDS whitelist profile : Location profile : Radio switch : enable Channel : - Channel bandwidth : 20mhz EIRP(dBm) : 127 Antenna gain(dB) : - Coverage distance(100 m) : 3 Work mode : normal Flexible radio switch : on Radio frequency : 2.4G Spectrum analysis : disable WIDS device detect : disable WIDS attack detect : - WIDS contain switch : disable Auto channel select : enable Auto transmit power select : enable Beacon switch : enable CTS switch : enable CTS delay time(us) : none Radio 1 Radio 5G profile : default VAP profile : Mesh profile : WDS profile : Mesh whitelist profile : WDS whitelist profile : Location profile : Radio switch : enable Channel : - Channel bandwidth : 20mhz EIRP(dBm) : 127 Antenna gain(dB) : - Coverage distance(100 m) : 3 Work mode : normal Flexible radio switch : on Radio frequency : 5G Spectrum analysis : disable WIDS device detect : disable WIDS attack detect : - WIDS contain switch : disable Auto channel select : enable Auto transmit power select : enable Beacon switch : enable CTS switch : enable CTS delay time(us) : none Radio 2 Radio 2.4G profile : default Radio 5G profile : default VAP profile : Mesh profile : WDS profile : Mesh whitelist profile : WDS whitelist profile : Location profile : Radio switch : enable Channel : - Channel bandwidth : 20mhz EIRP(dBm) : 127 Antenna gain(dB) : - Coverage distance(100 m) : 3 Work mode : normal Flexible radio switch : on Radio frequency : 5G Spectrum analysis : disable WIDS device detect : disable WIDS attack detect : - WIDS contain switch : disable Auto channel select : enable Auto transmit power select : enable Card 1 Card connect type : - Wired port profile : default Iot profile : Protocol Type : - First Port : - Extended Port : - Card 2 Card connect type : - Wired port profile : default Iot profile : Protocol Type : - First Port : - Extended Port : - Card 3 Card connect type : - Wired port profile : default Iot profile : Protocol Type : - First Port : - Extended Port : - Card usb Iot profile : Protocol Type : - First Port : - Extended Port : -
Item |
Description |
|---|---|
| AP system profile | AP system profile referenced by an AP group. To configure the parameter, run the ap-system-profile (AP group view and AP view) command. |
| Regulatory domain profile | Regulatory domain profile referenced by an AP group. To configure the parameter, run the regulatory-domain-profile command. |
| WIDS profile | WIDS profile referenced by an AP group. To configure the parameter, run the wids-profile (AP group view and AP view) command. |
| BLE profile | BLE profile referenced by an AP group. To configure the parameter, run the ble-profile (AP group view and AP view) command. |
| UUID | UUID of a BLE broadcast frame sent by the AP's built-in Bluetooth module. To configure the parameter, run the broadcasting-content (AP group view) command. |
| Site code | WLAN access site to which APs in the AP group belong. To configure the parameter, run the site command. |
| AP location | Installation position of an AP in the AP group. To configure the parameter, run the location command. |
| Domain name | Default domain name suffix of the AP. To configure the parameter, run the ip domain-name command. |
| AP wired port profile | AP wired port profile referenced by an AP group. To configure the parameter, run the wired-port-profile (AP group view and view) command. |
| Interface Interface-name | Interface name. |
| Radio 0/Radio 1/Radio 2 | Radio ID. |
| Radio 2.4G profile | 2G radio profile referenced by an AP group. To configure the parameter, run the radio-2g-profile command. |
| Radio 5G profile | 5G radio profile referenced by an AP group. To configure the parameter, run the radio-5g-profile command. |
| VAP profile | VAP profile referenced by an AP group. The displayed format is "VAP ID:VAP profile name (service VLAN defined when binding to the VAP profile, single VLAN, or VLAN pool)." To configure the parameter, run the vap-profile command. |
| Mesh profile | Mesh profile referenced by an AP group. To configure the parameter, run the mesh-profile radio command. |
| WDS profile | WDS profile referenced by an AP group. To configure the parameter, run the wds-profile radio command. |
| Mesh whitelist profile | Mesh whitelist profile referenced by an AP group. To configure the parameter, run the mesh-whitelist-profile (AP group radio view or AP radio view) command. |
| WDS whitelist profile | WDS whitelist profile referenced by an AP group. To configure the parameter, run the wds-whitelist-profile (AP group radio view or AP radio view) command. |
| Location profile | Location profile referenced by an AP group. To configure the parameter, run the location-profile command. |
| Radio switch | Whether a radio is enabled. To configure the parameter, run the radio disable command. |
| Channel | Working channel of a radio. To configure the parameter, run the channel command. |
| Channel bandwidth | Operating bandwidth of a radio. To configure the parameter, run the channel command. |
| EIRP(dBm) | Transmit power of a radio, in dBm. To configure the parameter, run the eirp command. |
| Antenna gain(dB) | Antenna gain of a radio, in dBm. To configure the parameter, run the antenna-gain command. |
| Coverage distance(100 m) | Radio coverage distance parameter (unit: 100 m). To configure the parameter, run the coverage distance command. |
| Work mode | Working mode of a radio. To configure the parameter, run the work-mode command. |
Flexible radio switch |
Whether the DFA function of a radio is enabled. To configure the parameter, run the calibrate flexible-radio disable command. |
| Radio frequency | Working frequency of a radio. To configure the parameter, run the frequency command. |
| Spectrum analysis | Whether spectrum analysis is enabled. To configure the parameter, run the spectrum-analysis enable command. |
| WIDS device detect | Whether wireless device detection is enabled. To configure the parameter, run the wids device detect enable command. |
| WIDS attack detect | Whether attack detection is enabled. To configure the parameter, run the wids attack detect enable command. |
| WIDS contain switch | Whether rogue device containment is enabled. To configure the parameter, run the wids contain enable command. |
| Auto channel select | Whether to enable automatic channel selection. To configure this parameter, run the calibrate auto-channel-select disable command. |
| Auto transmit power select | Whether to enable automatic transmit power selection. To configure this parameter, run the calibrate auto-txpower-select disable command. |
| Beacon switch | Whether RUs are enabled to send Beacon frames. To configure this parameter, run the beacon disable command. |
| CTS switch | Whether RUs are enabled to respond to STAs with CTS packets. To configure this parameter, run the cts disable command. |
| CTS delay time(us) | Delay time after which RUs respond to STAs with CTS packets. To configure this parameter, run the cts delay command. |
| Card 1/Card 2/Card 3/Card usb | IoT card. |
| Card connect type | Communication connection type between IoT cards and APs. To configure the parameter, run the card connect-type command. |
| Wired port profile | Bound AP wired port profile. To configure the parameter, run the wired-port-profile (IoT card interface view) command. |
| Iot profile | Bound IoT profile. To configure the parameter, run the iot-profile (IoT card interface view) command. |
| Protocol Type | Communication protocol between the AP and host computer. |
| First Port | Source port for the first channel. |
| Extended Port | Source port for the extended channel. |
| Highway profile | Highway profile referenced by an AP group. To configure the parameter, run the highway-profile (AP group view) command. This item is supported only by ACs supporting highway WLAN coverage. |
