No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Fat AP and Cloud AP V200R010C00 Command Reference

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
display ap-system-profile

display ap-system-profile

Function

The display ap-system-profile command displays reference and configuration information about an AP system profile.

Format

display ap-system-profile { all | name profile-name }

Parameters

Parameter

Description

Value

all

Displays information about all AP system profiles.

-

name profile-name

Displays information about a specified AP system profile.

The AP system profile must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display ap-system-profile command to view configuration and reference information about an AP system profile.

Example

# Display information about all AP system profiles.

<Huawei> display ap-system-profile all
----------------------------------------------------------
Profile name                   Reference
----------------------------------------------------------
default                        1
ap-system1                     0
----------------------------------------------------------
Total: 2
Table 18-30  Description of the display ap-system-profile all command output

Item

Description

Profile name

Name of an AP system profile.

Reference

Number of times an AP system profile is referenced.

# Display information about the AP system profile ap-system1.

<Huawei> display ap-system-profile name ap-system1
------------------------------------------------------------------------------
AC priority                                    : -
Protect AC IP address                          : -
Primary AC                                     : -
Backup AC                                      : -
AP management VLAN                             : -
Keep service                                   : -
Keep service allow new access                  : -
Keep service allow new access no auth          : -        
Temporary management switch                    : -
Mesh role                                      : -
STA access mode                                : disable
STA whitelist profile                          : -
STA blacklist profile                          : -
EAPOL start mode                               : multicast
EAPOL start transform                          : equal-bssid
EAPOL response mode                            : unicast learning
EAPOL response transform                       : equal-bssid
AP LLDP message transmission delay time(s)     : 2
AP LLDP message transmission hold multiplier   : 4
AP LLDP message transmission interval time(s)  : 30
AP LLDP restart delay time(s)                  : 2
AP LLDP admin status                           : txrx
AP LLDP report interval time(s)                : 30
AP LLDP report enable                          : disable
AP high temperature threshold(degree C)        : -
AP low temperature threshold(degree C)         : -
AP CPU usage threshold(%)                      : 90
AP memory usage threshold(%)                   : 80
Alarm restriction                              : enable
Alarm restriction period(s)                    : 60
Log server IP address                          : -
Log record level                               : info
Ethernet port MTU(byte)                        : 1500
Telnet                                         : disable
STelnet server                                 : enable
SFTP server                                    : enable
Console                                        : enable
Antenna output mode                            : -
Led                                            : on
Led off time range                             : -
DHCP client option12                           : ap-name
Report disassoc request                        : enable
Sample time(s)                                 : 30
Dynamic blacklist aging time(s)                : 600
MPP active reselection                         : -
AP report to                                   : server
Server IP                                      : 0.0.0.0
Server port                                    : -
AC port                                        : -
Device aging-time(minute)                      : 3
PoE max power(mW)                              : 380000
PoE power reserved(%)                          : -
PoE power threshold(%)                         : -
PoE af inrush                                  : disable
PoE high inrush                                : disable
USB                                            : disable
SSH config                                                                      
  Client first time                            : disable                        
  User interface vty 0                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                                                                                  
    ACL outbound                               : -                                                                                  
    ACL ipv6 inbound                           : -                                                                                  
    ACL ipv6 outbound                          : -           
  User interface vty 1                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                                                                                  
    ACL outbound                               : -                                                                                  
    ACL ipv6 inbound                           : -                                                                                  
    ACL ipv6 outbound                          : -           
  User interface vty 2                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                                                                                  
    ACL outbound                               : -                                                                                  
    ACL ipv6 inbound                           : -                                                                                  
    ACL ipv6 outbound                          : -           
  User interface vty 3                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                                                                                  
    ACL outbound                               : -                                                                                  
    ACL ipv6 inbound                           : -                                                                                  
    ACL ipv6 outbound                          : -           
  User interface vty 4                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24   
    ACL inbound                                : -                                                                                  
    ACL outbound                               : -                                                                                  
    ACL ipv6 inbound                           : -                                                                                  
    ACL ipv6 outbound                          : -           
Traffic optimize broadcast suppression ARP     : enable
Traffic optimize broadcast suppression IGMP    : enable
Traffic optimize broadcast suppression ND      : enable
Traffic optimize broadcast suppression DHCP    : enable                         
Traffic optimize broadcast suppression DHCPv6  : enable                         
Traffic optimize broadcast suppression MDNS    : enable                         
Traffic optimize broadcast suppression other broadcast       : enable           
Traffic optimize broadcast suppression other multicast       : enable 
Traffic optimize broadcast suppression ARP rate limit(pps)   : 256
Traffic optimize broadcast suppression IGMP rate limit(pps)  : 256
Traffic optimize broadcast suppression ND rate limit(pps)    : 256
Traffic optimize broadcast suppression DHCP rate limit(pps)  : 256              
Traffic optimize broadcast suppression DHCPv6 rate limit(pps): 256              
Traffic optimize broadcast suppression MDNS rate limit(pps)  : 256              
Traffic optimize broadcast suppression other broadcast rate limit(pps) : 256    
Traffic optimize broadcast suppression other multicast rate limit(pps) : 256  
Broadcast suppression auto-detect packets(pps)  : 256                           
Multicast suppression auto-detect packets(pps)  : 256                           
Unicast suppression auto-detect packets(pps)    : 128  
------------------------------------------------------------------------------
Table 18-31  Description of the display ap-system-profile name profile-name command output

Item

Description

AC priority

Central AP priority.

Protect AC IP address

IP address of the standby Central AP.

Primary AC

IP address of the primary Central AP.

Backup AC

IP address of the backup Central AP.

AP management VLAN

Management VLAN of an RU.

Temporary management switch

Status of management VAP and antenna alignment VAP for offline RUs.

Full vap create temporary management

Whether an offline management VAP is generated when the maximum VAP specifications are reached.

  • enable: An offline management VAP is generated.

  • disable: The service VAP is reserved, and no offline management VAP is generated.

NOTE:
Only cloud central APs support this parameter.
Mesh role

Mesh role.

STA access mode

STA access mode.

To configure the parameter, run the sta-access-mode command.

STA whitelist profile

Name of a STA whitelist profile referenced by an AP system profile.

To configure the parameter, run the sta-access-mode command.

STA blacklist profile

Name of a STA blacklist profile referenced by an AP system profile.

To configure the parameter, run the sta-access-mode command.

EAPOL start mode

Eapol-start packet encapsulation mode.

To configure the parameter, run the eapol-start dest-address transform-to command.

EAPOL start transform

Eapol-start packet conversion mode.

To configure the parameter, run the eapol-start dest-address transform-condition command.

EAPOL response mode

Eapol-response packet encapsulation mode.

To configure the parameter, run the eapol-response dest-address transform-to command.

EAPOL response transform

Eapol-response packet conversion mode.

To configure the parameter, run the eapol-response dest-address transform-condition command.

AP LLDP message transmission delay time(s)

Delay for an RU to send LLDP packets to neighbors.

To configure the parameter, run the lldp message-transmission delay (AP system profile view) command.

AP LLDP message transmission hold multiplier

Hold time multiplier of RU information on neighbors.

To configure the parameter, run the lldp message-transmission hold-multiplier (AP system profile view) command.

AP LLDP message transmission interval time(s)

Interval at which an RU sends LLDP packets to neighbors.

To configure the parameter, run the lldp message-transmission interval (AP system profile view) command.

AP LLDP restart delay time(s)

Delay in re-enabling LLDP.

To configure the parameter, run the lldp restart-delay command.

AP LLDP admin status
LLDP mode on an RU.
  • tx: The AP sends but does not receive LLDP packets.

  • rx: The AP receives but does not send LLDP packets.

  • txrx: The AP sends and receives LLDP packets.

To configure the parameter, run the lldp admin-status command.

AP LLDP report interval time(s)

Interval at which an RU reports LLDP neighbor information to a Central AP.

To configure the parameter, run the lldp report-interval command.

AP LLDP report enable

Whether an AP is enabled to report information about its LLDP neighbors.

To configure the parameter, run the lldp report enable command.

AP high temperature threshold(degree C)

High temperature alarm threshold of an RU.

To configure the parameter, run the high-temperature threshold command.

AP low temperature threshold(degree C)

Low temperature alarm threshold of an RU.

To configure the parameter, run the low-temperature threshold command.

AP CPU usage threshold(%)

CPU usage alarm threshold of an RU.

To configure the parameter, run the cpu-usage threshold command.

AP memory usage threshold(%)

Memory usage alarm threshold of an RU.

To configure the parameter, run the memory-usage threshold command.

Alarm restriction

Alarm suppression status of an RU.

To configure the parameter, run the alarm-restriction disable command.

Alarm restriction period(s)

Alarm suppression period of an RU.

To configure the parameter, run the alarm-restriction period command.

Log server IP address

IP address of the log server.

To configure the parameter, run the log-server command.

Log record level

Level of RU logs to be backed up.

To configure the parameter, run the log-record-level command.

Ethernet port MTU(byte)

MTU of Ethernet interfaces.

To configure the parameter, run the mtu command.

Telnet

Whether RU Telnet login is enabled.

To configure the parameter, run the telnet enable command.

STelnet server

STelnet server status of an RU.

To configure the parameter, run the stelnet server disable command.

SFTP server

SFTP server status of an RU.

To configure the parameter, run the sftp server disable command.

Console

Whether RU console port login is enabled.

To configure the parameter, run the console disable command.

Antenna output mode

Output mode of the RU's 2.4 GHz or 5 GHz antenna.

Led
Whether RU indicators are allowed to turn on.
  • on: The RU indicators are allowed to turn on.

  • off: The RU indicators are forbidden to turn on.

To configure the parameter, run the led off command.

Led off time range

Time range within which the AP indicators are forbidden to turn on.

To configure the parameter, run the led off command.

DHCP client option12
AP information contained in Option 12 carried in DHCP messages reported by an RU.
  • ap-name: RU name contained in Option 12 carried in DHCP messages reported by an RU.
  • ap-type ap-mac: RU type and MAC address contained in Option 12 carried in DHCP messages reported by an RU.
  • disable: The Option 12 is not carried in DHCP messages reported by an RU.

To configure the parameter, run the dhcp client option12 command.

Report disassoc request

Whether an RU is enabled to report disassociation request packets of STAs to the Central AP.

To configure the parameter, run the report-disassoc-request disable command.

Sample time(s)

RU's sampling interval.

To configure the parameter, run the sample-time command.

Dynamic blacklist aging time(s)

Aging time of a dynamic blacklist entry.

To configure the parameter, run the dynamic-blacklist aging-time command.

MPP active reselection

Active MPP reselection.

AP report to

Mode in which an RU reports spectrum data.
  • server: The RU reports spectrum data to a spectrum server directly.
  • via ac: The RU reports spectrum data to a spectrum server via the Central AP.

Server IP

IP address of the spectrum server.

Server port

Port number (UDP port number) of the spectrum server.

AC port

Port number used by the Central AP to receive spectrum data (in UDP packets) from the RU.

Device aging-time(minute)

Aging time of non-Wi-Fi device data on a Central AP.

PoE max power(mW)

Maximum output power of the central AP.

To configure the parameter, run the poe max-power (AP system profile view) command.

PoE power reserved(%)

Percentage of reserved PoE power to the available PoE power on the central AP.

To configure the parameter, run the poe power-reserved (AP system profile view) command.

PoE power threshold(%)

Alarm threshold of PoE power consumption percentage on the central AP.

To configure the parameter, run the poe power-threshold (AP system profile view) command.

PoE af inrush

PoE standard of the central AP.

To configure the parameter, run the poe af-inrush enable (AP system profile view) command.

PoE high inrush

Whether the central AP is enabled to allow high inrush current during power-on.

To configure the parameter, run the poe high-inrush enable (AP system profile view) command.

USB

USB status.

To configure the parameter, run the usb enable (AP system profile view) command.

SSH config

SSH configurations.

Client first time

Whether initial authentication is enabled on the SSH client.

To configure this parameter, run the ssh client first-time enable (AP system profile view) command.

User interface vty X

VTY user interface X. The value of X ranges from 0 to 4.

Idle timeout

Timeout period of user connections.

To configure this parameter, run the user-interface vty idle-timeout command.

Screen length

Number of lines on each terminal screen.

To configure this parameter, run the user-interface vty screen-length command.

ACL inbound

ACL that restricts STAs with a specified IPv4 address or within a specified IP address segment from logging in to the device.

To configure this parameter, run the user-interface vty acl command.

ACL outbound

ACL that restricts IPv4 STAs who have logged in to the device from logging in to other devices.

To configure this parameter, run the user-interface vty acl command.

ACL ipv6 inbound

ACL that restricts STAs with a specified IPv6 address or within a specified IP address segment from logging in to the device.

To configure this parameter, run the user-interface vty acl command.

ACL ipv6 outbound

ACL that restricts IPv6 STAs who have logged in to the device from logging in to other devices.

To configure this parameter, run the user-interface vty acl command.

Traffic optimize broadcast suppression ARP

Whether the suppression function is enabled for ARP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression IGMP

Whether the suppression function is enabled for IGMP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression ND

Whether the suppression function is enabled for ND packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression DHCP

Whether the suppression function is enabled for DHCP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression DHCPv6

Whether the suppression function is enabled for DHCPv6 packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression MDNS

Whether the suppression function is enabled for mDNS packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression other broadcast

Whether the suppression function is enabled for broadcast packets other than ARP, DHCP, DHCPv6, and ND packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression other multicast

Whether the suppression function is enabled for multicast packets other than IGMP and mDNS packets.

To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.

Traffic optimize broadcast suppression ARP rate limit(pps)

Rate threshold for ARP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression IGMP rate limit(pps)

Rate threshold for IGMP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression ND rate limit(pps)

Rate threshold for ND packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression DHCP rate limit(pps)

Rate threshold for DHCP packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression DHCPv6 rate limit(pps)

Rate threshold for DHCPv6 packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression MDNS rate limit(pps)

Rate threshold for mDNS packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression other broadcast rate limit(pps)

Rate threshold for broadcast packets other than ARP, DHCP, DHCPv6, and ND packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Traffic optimize broadcast suppression other multicast rate limit(pps)

Rate threshold for multicast packets other than IGMP and mDNS packets.

To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.

Broadcast suppression auto-detect packets(pps)

Rate threshold of broadcast packets.

To configure this parameter, run the broadcast-suppression auto-detect (AP system profile view) command.

Multicast suppression auto-detect packets(pps)

Rate threshold of multicast packets.

To configure this parameter, run the multicast-suppression auto-detect (AP system profile view) command.

Unicast suppression auto-detect packets(pps)

Rate threshold of unknown unicast packets.

To configure this parameter, run the unicast-suppression auto-detect (AP system profile view) command.

Translation
Download
Updated: 2019-11-21

Document ID: EDOC1100064352

Views: 204323

Downloads: 122

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next