No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Fat AP and Cloud AP V200R010C00 Command Reference

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
display eth-trunk

display eth-trunk

Function

The display eth-trunk command displays the configuration about an Eth-Trunk.

Format

display eth-trunk [ trunk-id [ interface interface-type interface-number | verbose ] ]

Parameters

Parameter Description Value
trunk-id Specifies the ID of an Eth-Trunk.

The value is an integer that ranges from 0 to 7.

interface interface-type interface-number Specifies a member interface.

interface-type specifies the type of the member interface.

interface-number specifies the number of the member interface.

-
verbose Displays the detailed configuration of a specified Eth-Trunk, including the statistics about interface traffic. -

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Usage Scenario

After configuring an Eth-Trunk on a device, you can run the display eth-trunk command to check whether the configuration of the Eth-Trunk is correct.

When using the display eth-trunk command, note that:

  • If no optional parameter is specified, the configurations of all Eth-Trunks are displayed.

  • If trunk-id is specified only, the configuration of a specified Eth-Trunk is displayed.

  • If trunk-id and interface interface-type interface-number are specified, the configuration of member interfaces of the specified Eth-Trunk is displayed.

  • If trunk-id is specified and verbose is configured, the detailed configuration of a specified Eth-Trunk is displayed, including the statistics about interface traffic.

Prerequisites

The interface specified in this command must be an existing one; otherwise, the system prompts an error.

Precautions

If there is a great deal of statistics about traffic on Eth-Trunks, you are recommended to specify Eth-Trunk ID or interface interface-type interface-number to filter output information. Otherwise, the following problems may occur due to excessive output information:
  • The displayed information is repeatedly updated, and required information cannot be located.

  • The system does not respond because of long-time information traverse and search.

Example

# Display the configuration of Eth-Trunk 1 in manual load balancing mode.
<Huawei> display eth-trunk 1
Eth-Trunk1's state information is:                                              
WorkingMode: NORMAL         Hash arithmetic: According to src-dst-ip            
Least Active-linknumber: 1  Max Bandwidth-affected-linknumber: 8                
Operate status: down        Number Of Up Port In Trunk: 0                       
--------------------------------------------------------------------------------
PortName                      Status      Weight                                
GigabitEthernet0/0/1          Up          1 
Table 6-10  Description of the display eth-trunk command output

Item

Description

WorkingMode

Operation mode of the Eth-Trunk:

  • NORMAL: manual load balancing mode

  • : LACP mode

Hash arithmetic

Hash algorithm used for load balancing among member interfaces of the Eth-Trunk.

Least Active-linknumber

Minimum number of active member links.

Max Bandwidth-affected-linknumber

Maximum number connections that affect the Eth-Trunk bandwidth.

Operate status

Status of the Eth-Trunk:
  • UP: The interface is Up.

  • DOWN: The interface is Down.

Number Of Up Port In Trunk

Number of Up member interfaces in the Eth-Trunk.

PortName

Name of a member interface.

Status

Status of local member interfaces in Manual Load Balancing Mode:
  • Up: indicates that the interface is properly started.

  • Down: indicates that the interface is faulty.

Weight

Weight of the member interface.

Translation
Download
Updated: 2019-11-21

Document ID: EDOC1100064352

Views: 204372

Downloads: 122

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next