display traffic-profile
Function
The display traffic-profile command displays configuration information about a traffic profile.
Usage Guidelines
You can run the display traffic-profile command to check default configurations of a new traffic profile or configurations of an existing traffic profile.
Example
# Display configuration information about a specified traffic profile.
<Huawei> display traffic-profile name p1
---------------------------------------------------------------------------------------------
Profile ID : 1
Priority map downstream trust : DSCP
User isolate mode : disable
Rate limit client up(Kbps) : 4294967295
Rate limit client down(Kbps) : 4294967295
Rate limit VAP up(Kbps) : 4294967295
Rate limit VAP down(Kbps) : 4294967295
Rate limit client dynamic switch : enable
Rate limit client dynamic(Mbps) : 16
Traffic optimize ARP proxy : disable
Traffic optimize ARP unicast send : enable
Traffic optimize DHCP unicast send : disable
Traffic optimize multicast send deny : disable
Traffic optimize TCP adjust MSS(bytes) : -
Traffic optimize bcmc unicast send mismatch action : traverse
MLD snooping : -
IGMP snooping : enable
IGMP snooping report suppress : -
IGMP snooping max bandwith(kbps) : -
IGMP snooping max user : -
Traffic optimize sta bridge forward : enable
Traffic optimize broadcast suppression(pps) : -
Traffic optimize multicast suppression(pps) : -
Traffic optimize unicast suppression(pps) : -
Traffic optimize multicast to unicast : disable
Dynamic adaptive : disable
WMM priority downstream map mode : DSCP map 802.11e
0-7 map 0
8-15 map 1
16-23 map 2
24-31 map 3
32-39 map 4
40-47 map 5
48-55 map 6
56-63 map 7
WMM priority downstream map mode : 802.1p map 802.11e
0 map 0
1 map 1
2 map 2
3 map 3
4 map 4
5 map 5
6 map 6
7 map 7
---------------------------------------------------------------------------------------------
Traffic Type Direction AppliedRecord
---------------------------------------------------------------------------------------------
traffic-filter inbound IPv4 ACL 3001 & L2 ACL 4001
---------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------
Traffic Type Direction RemarkType RemarkValue AppliedRecord
---------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------
Item |
Description |
|---|---|
Profile ID |
Traffic profile ID |
Priority map downstream trust |
Mapping from the 802.1p or DSCP priority of 802.3 packets to the 802.11 user priority when 802.3 packets are sent to an RU from upper-layer devices. To configure the parameter, run the priority-map downstream trust command. |
User isolate mode |
User isolation. To configure the parameter, run the user-isolate (traffic profile view) command. |
Rate limit client up(Kbps) |
Indicates upstream rate limit configured for STAs. To configure the parameter, run the rate-limit command. |
Rate limit client down(Kbps) |
Indicates downstream rate limit configured for STAs. To configure the parameter, run the rate-limit command. |
Rate limit VAP up(Kbps) |
Indicates upstream rate limit configured for VAPs. To configure the parameter, run the rate-limit command. |
Rate limit VAP down(Kbps) |
Indicates downstream rate limit configured for VAPs. To configure the parameter, run the rate-limit command. |
Rate limit client dynamic switch |
Whether dynamic rate limiting is enabled for a single STA in a VAP. To configure this parameter, run the rate-limit client dynamic disable command. |
Rate limit client dynamic(Mbps) |
Dynamic rate limit threshold of a single STA in a VAP. To configure this parameter, run the rate-limit client dynamic command. |
Traffic optimize ARP proxy |
ARP proxy. |
Traffic optimize ARP unicast send |
Function of converting broadcast or multicast ARP packets to unicast ARP packets. |
Traffic optimize DHCP unicast send |
Function of converting broadcast or multicast DHCP packets to unicast DHCP packets. |
Traffic optimize multicast send deny |
Function of forbidding multicast packet forwarding. |
Traffic optimize sta bridge forward |
Function of forbidding STA bridging packet forwarding. |
Traffic optimize bcmc unicast send mismatch action |
Action when broadcast or multicast packets fail to be converted into unicast packets on air interfaces. To configure the parameter, run the traffic-optimize bcmc unicast-send mismatch-action drop command. |
MLD snooping |
MLD snooping. |
IGMP snooping |
IGMP snooping. |
IGMP snooping report suppress |
IGMP message suppression time. |
IGMP snooping max bandwith(kbps) |
Maximum multicast bandwidth of a VAP. To configure this parameter, run the igmp-snooping max-bandwidth (traffic profile view) command. |
IGMP snooping max user |
Maximum number of multicast group memberships on a VAP. To configure this parameter, run the igmp-snooping max-user (traffic profile view) command. |
Traffic optimize broadcast suppression(pps) |
Maximum broadcast traffic volume allowed on an interface. To configure the parameter, run the traffic-optimize broadcast-suppression command. |
Traffic optimize multicast suppression(pps) |
Maximum multicast traffic volume allowed on an interface. To configure the parameter, run the traffic-optimize multicast-suppression command. |
Traffic optimize unicast suppression(pps) |
Maximum unicast traffic volume allowed on an interface. To configure the parameter, run the traffic-optimize unicast-suppression command. |
Traffic optimize multicast to unicast |
Function of converting multicast packets to unicast packets. To configure the parameter, run the traffic-optimize multicast-unicast enable command. |
Dynamic adaptive |
Whether to enable adaptive multicast-to-unicast conversion. To configure this function, run the traffic-optimize multicast-unicast dynamic-adaptive disable command. |
Traffic optimize TCP adjust MSS(bytes) |
MSS of TCP packets on an interface. |
WMM priority downstream map mode |
Mapping from the DSCP priority to the WMM of downstream packets. |
Traffic Type |
Traffic control type. |
Direction(Traffic Type: traffic-filter) |
Direction of packets to be filtered. To configure this parameter, run the traffic-filter (traffic profile view) command. |
AppliedRecord(Traffic Type: traffic-filter) |
ACL-based packet filtering records. To configure this parameter, run the traffic-filter (traffic profile view) command. |
| Direction(Traffic Type: traffic-remark) | Direction to which packet priority re-marking is applied. To configure this parameter, run the traffic-remark (traffic profile view) command. |
| RemarkType | Packet priority re-marking type. To configure this parameter, run the traffic-remark (traffic profile view) command. |
| RemarkValue | Re-marked packet priority value. To configure this parameter, run the traffic-remark (traffic profile view) command. |
| AppliedRecord(Traffic Type: traffic-remark) | ACL-based packet priority re-marking record. To configure this parameter, run the traffic-remark (traffic profile view) command. |
# Display configurations of all traffic profiles.
<Huawei> display traffic-profile all
----------------------------------------------------
Profile name Reference
----------------------------------------------------
default 3
1 1
p1 0
----------------------------------------------------
Total: 3
Item |
Description |
|---|---|
Profile name |
Profile name. To configure the parameter, run the traffic-profile (WLAN view) command. |
Reference |
Number of times a location profile is referenced. |
Previous
