No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Command Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
beamforming enable

beamforming enable

Function

The beamforming enable command enables Beamforming.

The undo beamforming enable command disables Beamforming.

By default, Beamforming is disabled.

Format

beamforming enable

undo beamforming enable

Parameters

None

Views

2G radio profile view, 5G radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Beamforming is a signal processing technique that controls signal transmission direction, and transmission and reception of radio signals. The transmit end uses weight to transmit signals. The signals are transmitted to the destination as narrow beams. Beamforming increases the signal-to-noise ratio (SNR) for the destination device.

Precautions

If nodes on the WDS or Mesh network are fixed and distant from each other, enable Beamforming to increase WDS or Mesh link SNR. Mobile nodes may cause low link SNR in WDS or Mesh scenarios. To prevent this problem, disable Beamforming.

Table 11-1 describes the support of Huawei APs for beamforming.
Table 11-1  Support of APs for Beamforming
AP Model Explicit 802.11ac Beamforming Explicit 802.11n Beamforming Implicit Beamforming
2.4 GHz 5 GHz
AP3010DN, AP5010SN, AP5010DN, AP6010SN, AP6010DN, AP6310SN, AP6510DN, AP6610DN, AP7110SN, AP7110DN, AP2010DN N Y Y N
AP5030DN, AP5130DN, AP2030DN, AP2030DN-S, AP3030DN, AP4030DN, AP4130DN, AP3010DN-V2, AP5030DN-S, AP9131DN, AP9132DN, AD9430DN-12 (with R240D), AD9430DN-24 (with R240D), AD9431DN-24X (with R240D), AP4030DN-E, AP4030TN, AP430-E, AP4051TN N Y N N
AP8030DN, AP8130DN, AD9430DN-12 (with R230D), AD9430DN-24 (with R230D), AD9431DN-24X (with R230D), AP1010SN N N N N
AD9430DN-12 (with R250D, R251D), AD9430DN-24 (with R250D, R251D, R450D, R251D-E and R250D-E), AD9431DN-24X (with R250D, R251D, R450D, R251D-E and R250D-E), AP2050DN, AP2050DN-S, AP2050DN-E, AP2051DN, AP2051DN-E, AP2051DN-S, AP2051DN-L-S, AP5510-W-GP Y Y Y Y
AP7030DE, AP9330DN N N N Y

Example

# Enable Beamforming.

<HUAWEI> system-view
[HUAWEI] wlan 
[HUAWEI-wlan-view] radio-2g-profile name default
[HUAWEI-wlan-radio-2g-prof-default] beamforming enable
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065659

Views: 123887

Downloads: 88

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next