No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Command Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
dot11bg supported-rate

dot11bg supported-rate

Function

The dot11bg supported-rate command configures a supported rate set of the 802.11bg protocol in a 2G radio profile.

The undo dot11bg supported-rate command restores the default supported rate set of the 802.11bg protocol in a 2G radio profile.

By default, the supported rate set of the 802.11bg protocol in a 2G radio profile includes rates 1 Mbps, 2 Mbps, 5.5 Mbps, 6 Mbps, 9 Mbps, 11 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps.

Format

dot11bg supported-rate { dot11bg-rate-value &<1-12> | all }

undo dot11bg supported-rate

Parameters

Parameter

Description

Value

dot11bg-rate-value

Specifies an 802.11bg supported rate set.

Enumerated type:
  • 1: 1 Mbps
  • 2: 2 Mbps
  • 5: 5.5 Mbps
  • 6: 6 Mbps
  • 9: 9 Mbps
  • 11: 11 Mbps
  • 12: 12 Mbps
  • 18: 18 Mbps
  • 24: 24 Mbps
  • 36: 36 Mbps
  • 48: 48 Mbps
  • 54: 54 Mbps

all

Supports all rates.

-

Views

2G radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The supported rate set contains rates supported by the AP except the basic rates. The AP and STA can transmit data at all rates specified by the supported rate set. The AP and STA select a rate from the basic rate set or the supported rate set to transmit packets.

When a STA supports rates specified in the basic rate set, the STA can associate with the AP regardless of whether the STA supports rates specified in the supported rate set. In this case, the AP and STA can only select a rate from the basic rate set to transmit packets. For example, assume that you configure the basic rate set to contain rates 6 Mbps and 9 Mbps and the supported rate set to contain rates 48 Mbps and 54 Mbps. After you deliver the configurations to an AP, the STA supporting 6 Mbps and 9 Mbps can associate with the AP, and select either of the two rates to transmit packets with the AP. However, if the STA supports 6 Mbps, 9 Mbps, and 54 Mbps, the STA and AP select any of the three rates to transmit packets after the STA associates with the AP.

After you run this command to configure a supported rate set in a radio profile, bind the radio profile to an AP or AP group. If a STA associates with the AP in 802.11bg mode, the AP and STA select a rate from the basic rate set or supported rate set to transmit packets.

Precautions

This configuration applies only to STAs associated with an AP in 802.11bg mode but does not take effect on STAs associated with the AP in other modes.

The basic rate set and supported rate set cannot be empty simultaneously.

Example

# Configure the 802.11bg supported rate set to contain rates 6 Mbps and 9 Mbps in the 2G radio profile default.

<HUAWEI> system-view
[HUAWEI] wlan 
[HUAWEI-wlan-view] radio-2g-profile name default
[HUAWEI-wlan-radio-2g-prof-default] dot11bg supported-rate 6 9
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065659

Views: 126225

Downloads: 88

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next