No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Command Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
SAID Configuration Commands

SAID Configuration Commands

Command Support

Only V200R013C00SPC500 supports SAID.

display said-node brief

Function

The display said-node brief command displays brief information about SAID nodes.

Format

display said-node { all | said-name } brief [ slot slot-id ]

Parameters

Parameter

Description

Value

all

Indicates all SAID nodes.

-

said-name

Specifies an SAID node.

The value depends on the device configuration.

slot slot-id

Specifies a slot ID.

If no slot ID is specified, this command displays brief information about SAID nodes on the active MPU.

The value depends on the device configuration.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display said-node brief command to view brief information about all supported SAID nodes for fault location.

Example

# Display brief information about the SAID node named mac in slot 2.

<HUAWEI> display said-node mac brief slot 2
--------------------------------------------------------------------------------------------
Node  Node             Type    Cycle  Enable   Active      Inactive Reason
ID    Name                     (s)    Status   Status
--------------------------------------------------------------------------------------------
2     mac              Restore 1      Enable   Active      -
--------------------------------------------------------------------------------------------
Table 3-190  Description of the display said-node brief command output

Item

Description

Node ID

ID of an SAID node.

Node Name

Name of the SAID node.

Type

Type of the SAID node:
  • Detect: diagnostic node
  • Restore: self-healing node

Cycle(s)

Detection period of the SAID node, in seconds.

Enable Status

Whether the SAID node is enabled:
  • Enable: The SAID node is enabled.
  • Disable: The SAID node is disabled.

Active Status

Running status of the SAID node:
  • Active: The SAID node is running.
  • Disable: The SAID node is not running.

Inactive Reason

Whether the SAID node is activated:
  • -: The SAID node is enabled and activated.
  • Node disabled: The SAID node is not activated.

set said-node disable

Function

The set said-node disable command disables SAID nodes.

The undo set said-node disable command enables SAID nodes.

By default, all SAID nodes are enabled.

Format

set said-node { all | said-name &<1-6> } disable

undo set said-node { all | said-name &<1-6> } disable

Parameters

Parameter

Description

Value

all

Indicates all SAID nodes.

-

said-name

Specifies an SAID node.

The value depends on the device configuration.

A maximum of six SAID nodes can be configured at a time. If you need to configure more than six SAID nodes, run the set said-node disable command multiple times.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The System of Active Immunization and Diagnosis (SAID) is an intelligent fault diagnosis system that automatically diagnoses and rectifies some faults by simulating human operations in troubleshooting. The SAID system has multiple SAID nodes, which detect, diagnose, and rectify faults of multiple modules. However, if a node processes a large number of services, the processing efficiency of other nodes is affected. In this case, run this command disable this node.

Precautions

If some cards do not support a specific SAID node and no cards that support this SAID node are installed on the device, the device displays a message, indicating that the device does not support this SAID node.

Example

# Disable the SAID nodes mac and stg.

<HUAWEI> system-view
[HUAWEI] set said-node mac stg disable

# Disable all SAID nodes.

<HUAWEI> system-view
[HUAWEI] set said-node all disable
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065659

Views: 128110

Downloads: 88

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next