No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Command Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
display capwap configuration

display capwap configuration

Function

The display capwap configuration command displays the CAPWAP configuration.

Format

display capwap configuration

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view the interval for sending Keepalive packets, number of times for sending Keepalive packets, and priority of CAPWAP management packets.

Example

# Display the CAPWAP configuration.

<HUAWEI> display capwap configuration
  ------------------------------------------------------------
  Source interface                             : vlanif100
  Source ip-address                                : -
  Echo interval(seconds)                       : 25
  Echo times                                   : 6
  Control priority(server to client)           : 7
  Control priority(client to server)           : 7
  Control-link DTLS encrypt                    : disable
  DTLS PSK value                               : ******
  PSK mandatory match switch                   : enable
  Control-link inter-controller DTLS encrypt   : disable
  Inter-controller DTLS PSK value              : ******
  Message-integrity PSK value                  : ****** 
  Message-integrity check switch               : enable
  Sensitive-info PSK value                     : ******
  Sensitive-info inter-controller PSK value    : ******   
  ------------------------------------------------------------
Table 11-52  Description of the display capwap configuration command output

Item

Description

Source interface

AC's source interface.

To configure the parameter, run the capwap source interface command.

Source ip-address

AC's source address.

Echo interval(seconds)

Interval for sending Keepalive packets.

To specify the interval for sending Keepalive packets, run the capwap echo interval command.

Echo times

Number of times for sending Keepalive packets. If the AC or APs receive no response from each other after the Keepalive packets are sent for the specified number of times, the AC or APs consider that they are disconnected from their peer devices.

To specify the number of times for sending Keepalive packets, run the capwap echo times command.

Control priority(server to client)

Priority of CAPWAP management packets from an AC to an AP.

To configure the priority of CAPWAP management packets from an AC to an AP, run the capwap control-link-priority local priority-value command.

Control priority(client to server)

Priority of CAPWAP management packets from an AP to an AC.

To configure the priority of CAPWAP management packets from an AP to an AC, run the capwap control-link-priority remote priority-value command.

Control-link DTLS encrypt

Whether CAPWAP control tunnel encryption using DTLS is enabled.

To enable CAPWAP control tunnel encryption using DTLS, run the capwap dtls control-link encrypt command.

DTLS PSK value

PSK for DTLS encryption.

To configure the PSK for DTLS encryption, run the capwap dtls psk command.

PSK mandatory match switch

Whether an AP is enabled to perform DTLS sessions with the AC using the default PSK.

To enable an AP to perform DTLS sessions with the AC using the default PSK, run the capwap dtls psk-mandatory-match enable command.

Control-link inter-controller DTLS encrypt

Whether DTLS encryption for an inter-AC control tunnel is enabled.

To configure the parameter, run the capwap dtls inter-controller control-link encrypt command.

Inter-controller DTLS PSK value

PSK used for DTLS encryption of an inter-AC tunnel.

To configure the parameter, run the capwap dtls inter-controller psk command.

Message-integrity PSK value

PSK used for checking integrity of CAPWAP packets.

To configure the parameter, run the capwap message-integrity psk command.

Message-integrity check switch

Whether integrity check of CAPWAP packets is enabled.

To configure the parameter, run the capwap message-integrity check disable command.

Sensitive-info PSK value

PSK used for encrypting sensitive information.

To configure the parameter, run the capwap sensitive-info psk command.

Sensitive-info inter-controller PSK value

PSK used for encrypting sensitive information between ACs.

To configure the parameter, run the capwap inter-controller sensitive-info psk command.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065659

Views: 114470

Downloads: 83

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next