No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Command Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
priority-map tunnel-upstream dot11e dot1p

priority-map tunnel-upstream dot11e dot1p

Function

The priority-map tunnel-upstream dot11e dot1p command configures mapping from user priorities of 802.11 packets to 802.1p priorities of tunnel packets when packets are sent to the AC from an AP.

The undo priority-map tunnel-upstream dot11e dot1p command restores the default mapping from user priorities of 802.11 packets to 802.1p priorities of tunnel packets when packets are sent to the AC from an AP.

By default, user priority 0 of 802.11 packets maps to 802.1p priority 0 of tunnel packets, user priority 1 to 802.1p priority 1, and similarly, user priority 7 to 802.1p priority 7.

Format

priority-map tunnel-upstream dot11e { dot11e-value1 [ to dot11e-value2 ] } &<1-7> dot1p dot1p-value

undo priority-map tunnel-upstream dot11e to dot1p

Parameters

Parameter

Description

Value

dot11e dot11e-value1

Specifies the 802.11 user priority.

The value is an integer that ranges from 0 to 7. A larger value indicates a higher priority.

to dot11e-value2

Specifies the 802.11 user priority.

The value is an integer that ranges from 0 to 7. A larger value indicates a higher priority.

dot11e-value2 must be greater than dot11e-value1.

dot1p dot1p-value

Specifies the 802.1p priority in a tunnel packet.

The value is an integer that ranges from 0 to 7. A larger value indicates a higher priority.

Views

Traffic profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

To provide QoS guarantee for data packets of different users when packets are transmitted over a tunnel, configure a specific tunnel priority or priority mapping.

802.11 packets sent from a WMM-capable STA carry user priorities (Layer 2 priorities) or DSCP priorities (Layer 3 priorities). Tunnel packets carry 802.1p priorities (Layer 2 priorities) or DSCP priorities (Layer 3 priorities). When data packets are sent from APs to the AC, 802.11 packets need to be converted to tunnel packets.

You can run the priority-map tunnel-upstream dot11e dot1p command to configure mapping from user priorities of 802.11 packets to 802.1p priorities of tunnel packets when packets are sent to the AC from an AP.

Precautions

The tunnel priority mapping is applicable to scenarios where data packets are sent in tunnel forwarding mode.

Example

# In traffic profile p1, map user priority 6 of 802.11 packets to 802.1p priority 1 of tunnel packets when data is sent from APs to the AC.

<HUAWEI> system-view
[HUAWEI] wlan
[HUAWEI-wlan-view] traffic-profile name p1 
[HUAWEI-wlan-traffic-prof-p1] priority-map tunnel-upstream dot11e 6 dot1p 1
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065659

Views: 126589

Downloads: 88

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next