No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ACLE

ACLE

ACLE/3/IPC_FAIL

Message

ACLE/3/IPC_FAIL:IPC failed to send message to the slot [ULONG]. (MessageName=[STRING])

Description

The MPU failed to send IPC messages to an LPU.

Parameters

Parameter Name Parameter Meaning
[ULONG] Indicates the slot ID of the LPU.
MessageName
Indicates the name of message where an IPC error occurs, for example:
  • ACL_MSG_SET_TRAFFIC_POLICY: An ACL traffic policy is used.
  • ACL_MSG_UNSET_TRAFFIC_POLICY: No ACL traffic policy is used.

Possible Causes

Failed to send IPC messages. If an IPC failure occurs, the LPU may be abnormal.

Procedure

  1. Run the display device command to check whether the LPU has registered.

    • If so, go to step 3.
    • If not, go to step 2.

  2. If the LPU has not registered, IPC communication fails, which is normal. This log is informational only, and no action is required.
  3. Collect log information about IPC message sending failures of the LPU, and contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

ACLE/3/POLICY_APPLY

Message

ACLE/3/POLICY_APPLY: Failed to apply the policy to [STRING]. (ErrorInformation=[STRING])

Description

Failed to deliver a traffic policy.

Parameters

Parameter Name Parameter Meaning
[STRING] Indicates the view to which a traffic policy is applied.
ErrorInformation Indicates the error reason.

Possible Causes

A configuration conflict occurred or resources were insufficient.

Procedure

  1. Run the display traffic-policy applied-record command to check whether the traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to step 2.

  2. Check whether MQC has a configuration conflict according to error information in the logs.

    • If so, go to step 3.
    • If not, go to step 4.

  3. Remove the conflicting configuration and reconfigure a traffic policy. Run the display traffic-policy applied-record command to check whether the new traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to step 7.

  4. Check whether MQC has insufficient resources according to error information in the logs.

    • If so, go to step 5.
    • If not, go to step 7.

  5. Run the display traffic-policy applied-record command to check whether redundant traffic policies are configured.

    • If so, go to step 6.
    • If not, go to step 7.

  6. Delete redundant traffic policies and reconfigure a traffic policy. Run the display traffic-policy applied-record command to check whether the new traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to step 7.

  7. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

ACLE/4/POLICYPKTDROP

Message

ACLE/4/POLICYPKTDROP: Some packets are droped by traffic policy. (PolicyName=[STRING1], SlotID=[STRING2], Direction=[STRING3], DropCount=[STRING4])

Description

Statistics about dropped packets are collected after traffic rate limiting is configured globally and traffic statistics collection is enabled.

Parameters

Parameter Name Parameter Meaning
STRING1

Indicates the name of a traffic policy.

STRING2

Indicates the slot ID to which the traffic policy is applied.

STRING3

Indicates the direction in which the traffic policy is applied.

STRING4

Indicates the dropped packet statistics collected using the traffic policy.

Possible Causes

The traffic rate limit configured in the traffic policy is too low.

Procedure

  1. Run the display traffic policy user-defined command to view the CIR and PIR configured in the traffic policy specified in the log.
  2. Run the car (traffic behavior view) command to increase the CIR and PIR configured in the traffic policy.

ACLE/3/RESOURCE_APPLY

Message

ACLE/3/RESOURCE_APPLY:"[STRING]"

Description

Failed to deliver an ACL-based simplified traffic policy.

Parameters

Parameter Name Parameter Meaning
[STRING]

Indicates the reason for the failure of ACL-based simplified traffic policy delivery.

Possible Causes

  • Configuration conflict
  • ACL resource insufficiency

Procedure

  1. Run the display traffic-applied record command to check whether the ACL-based simplified traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to step 2.

  2. Check whether there is a configuration conflict according to error information in the logs.

    • If so, go to step 3.
    • If not, go to step 4.

  3. Remove the conflicting configuration, reconfigure an ACL-based simplified traffic policy, and run the display traffic-applied record command to check whether the new ACL-base simplified traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to setp 7.

  4. Check whether MQC has insufficient ACL resources according to error information in the logs.

    • If so, go to step 5.
    • If not, go to setp 7.

  5. Run the display traffic-applied record command to check whether redundant ACL-based simplified traffic policies are configured.

    • If so, go to step 6.
    • If not, go to setp 7.

  6. Delete redundant ACL-based simplified traffic policies, reconfigure an ACL-based simplified traffic policy, and run the display traffic-applied record command to check whether the new ACL-based simplified traffic policy is applied successfully.

    • If so, no further action is required.
    • If not, go to setp 7.

  7. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

ACLE/4/ACLLOG

Message

ACLE/4/ACLLOG:[STRING]

Description

This log is displayed when logging is specified in the ACL.

Parameters

Parameter Name Parameter Meaning
[STRING] Indicates the ACL number, deny/permit rule, interface name, time range, source MAC address, destination MAC address, protocol type, source IP address, source port number in UDP or TCP packets, destination IP address, destination port number in UDP or TCP packets.

Possible Causes

The packet matches an ACL.

Procedure

  • This log message is informational only, and no action is required.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065665

Views: 5599

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next