No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ISIS

ISIS

ISIS/6/AC_RT_SEL_FAIL

Message

ISIS/6/AC_RT_SEL_FAIL:ISIS [process-id] failed to invoke the active route [route] selection. (RouteEntryTable=[ULONG], EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to select AN active route.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[route]

Indicates a route.

RouteEntryTable

Indicates a routing table.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to select an active route.

Procedure

  1. Check the current routing information.

ISIS/6/AC_RT_V6_SEL_FAIL

Message

ISIS/6/AC_RT_V6_SEL_FAIL:ISIS [process-id] failed to invoke the IPv6 active route [route] selection. (RouteEntryTable=[ULONG], EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to select an IPv6 active route.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[route]

Indicates a route.

RouteEntryTable

Indicates a routing table.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to select an IPv6 active route.

Procedure

  1. Check the current routing information.

ISIS/6/ADD_L1_SUMRT_FAIL

Message

ISIS/6/ADD_L1_SUMRT_FAIL:ISIS [process-id] failed to add the Level-1 summary route. (MTID=[USHORT])

Description

IS-IS failed to add a summarized Level-1 route.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

MTID

Indicates the ID of a topology.

Possible Causes

Failed to add a summarized Level-1 route.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/ADD_L2_SUMRT_FAIL

Message

ISIS/6/ADD_L2_SUMRT_FAIL:ISIS [process-id] failed to add the Level-2 summary route. (MTID=[USHORT])

Description

IS-IS failed to add a summarized Level-2 route.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

MTID

Indicates the ID of a topology.

Possible Causes

Failed to add a summarized Level-2 route.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/ADD_LKINFO_CSPF_FAIL

Message

ISIS/6/ADD_LKINFO_CSPF_FAIL:ISIS [process-id] failed to add TE link information to CSPF. (ReturnValue=[ULONG], NeighborSystemId=[STRING], NeighborPseudoNodeId=[USHORT], NodeStatus=[USHORT], FragmentNumber=[USHORT])

Description

IS-IS failed to add TE link information to CSPF.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

ReturnValue

specifies a returned value.

NeighborSystemId

Indicates the system ID of a neighbor.

NeighborPseudoNodeId

Indicates the pseudo node ID of a neighbor.

NodeStatus

Indicates the status of a node.

FragmentNumber

Indicates the fragment number.

Possible Causes

1. CSPF was not enabled.

2. The message queue of CSPF was full.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/ADD_MDF_LK_CSPF_FAIL

Message

ISIS/6/ADD_MDF_LK_CSPF_FAIL:ISIS [process-id] failed to modify TE link information in CSPF. (ReturnValue=[ULONG], NeighborSystemId=[STRING], NeighborPseudoNodeId=[USHORT], NodeStatus=[USHORT], FragmentNumber=[USHORT])

Description

IS-IS failed to modify the TE link information in the CSPF.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

ReturnValue

Indicates a returned value.

NeighborSystemId

Indicates the system ID of a neighbor.

NeighborPseudoNodeId

Indicates the pseudo node ID of a neighbor.

NodeStatus

Indicates the status of a node.

FragmentNumber

Indicates the fragment number.

Possible Causes

1. CSPF was not enabled.

2. The message queue of CSPF was full.

Procedure

  1. Check whether CSPF is enabled.

    • If so, go to Step 3.

    • If not, go to Step 2.

  2. Enable CSPF, and check whether the log message is displayed again.

    • If so, go to Step 3.

    • If not, go to Step 4.

  3. Collect log information and configuration information, and then contact technical support personnel.
  4. End.

ISIS/6/ADD_NTWK_MPLS_FAIL

Message

ISIS/6/ADD_NTWK_MPLS_FAIL:ISIS [process-id] failed to add network information to MPLS TE. (ReturnValue=[ULONG])

Description

IS-IS failed to add network information to MPLS TE.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
ReturnValue Indicates a returned value.

Possible Causes

1. The message queue of the CSPF module was full.

2. An internal error occurred.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/ADD_P2P_ADJ_ERR

Message

ISIS/6/ADD_P2P_ADJ_ERR:Advertising P2P adjacency failed. (InterfaceName=[STRING], MTID=[USHORT])

Description

Failed to add a P2P neighbor.

Parameters

Parameter Name Parameter Meaning

InterfaceName

Indicates the name of an interface.

MTID

Indicates the ID of a topology.

Possible Causes

Internal processing.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/ADD_REDSTRBT_RT_FAIL

Message

ISIS/6/ADD_REDSTRBT_RT_FAIL:ISIS [process-id] failed to add the Level-[level] redistributed route [route] into the forwarding table. (MTID=[USHORT])

Description

IS-IS failed to add an imported route.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[level] Indicates the IS-IS level.
[route] Indicates a route.
MTID Indicates the ID of a topology.

Possible Causes

Failed to add an imported route.

Procedure

  1. Check information about the route.

ISIS/6/ADD_RTTO_LSP_FAIL

Message

ISIS/6/ADD_RTTO_LSP_FAIL:ISIS [process-id] failed to add the route to the LSP. (MTID=[USHORT])

Description

IS-IS failed to add a route to an LSP.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
MTID Indicates the ID of a topology.

Possible Causes

Failed to add a route to an LSP.

Procedure

  1. Check the current routing information.

ISIS/6/ADD_SUMMRT_URT_FAIL

Message

ISIS/6/ADD_SUMMRT_URT_FAIL:ISIS [process-id] failed to add NULL0 route to URT for summary. (MTID=[USHORT])

Description

IS-IS failed to add a null 0 summarized route to the URT.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
MTID Indicates the ID of a topology.

Possible Causes

Failed to add a null 0 summarized route to the URT.

Procedure

  1. Check the current routing information.

ISIS/6/ADD_SUMRT_FAIL

Message

ISIS/6/ADD_SUMRT_FAIL:ISIS [process-id] failed to add the summary route for redistribute route. (MTID=[USHORT])

Description

IS-IS failed to summarize the imported routes.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
MTID Indicates the ID of a topology.

Possible Causes

A summarized route was added.

Procedure

  1. Check why IS-IS failed to aggregate imported routes.

ISIS/6/ADD_TE_TLV_FAIL

Message

ISIS/6/ADD_TE_TLV_FAIL:ISIS [process-id] failed to add tunnel neighbour TLV to link state database.

Description

IS-IS failed to add the tunnel neighbor TLV to the LSDB.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to add the tunnel neighbor TLV to the LSDB.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/ADJ_CHANGE_LEVEL

Message

ISIS/4/ADJ_CHANGE_LEVEL:The neighbor of ISIS was changed. (IsisProcessId=[USHORT], Neighbor=[STRING], InterfaceName=[STRING], CurrentState=[STRING], ChangeType=[STRING], Level=[STRING])

Description

The IS-IS neighbor changed.

Parameters

Parameter Name Parameter Meaning

IsisProcessId

Indicates the ID of an IS-IS process.

Neighbor

Indicates the system ID of a neighbor.

InterfaceName

Indicates the name of an interface.

CurrentState

Indicates the current status, including the following:
  • UP

  • INIT

  • DOWN

ChangeType

Indicates the type of a change.
  • MULTIPLE_P2P_AD: indicates that repeated P2P neighbors appear.

  • L1_CIRCUIT_DOWN: indicates that the Level-1 interface is Down.

  • L2_CIRCUIT_DOWN: indicates that the Level-2 interface is Down.

  • CIRCUIT_DOWN: indicates that the P2P interface is Down.

  • CLEAR_L1_NEIGHBOUR: indicates that the Level-1 neighbor changes after the undo isis command is used.

  • CLEAR_L2_NEIGHBOUR: indicates that the Level-2 neighbor changes after the undo isis command is used.

  • CLEAR_NEIGHBOUR: indicates that the P2P neighbor changes after the undo isis command is used.

  • P2P_HOLDTIMER_EXPIRED: indicates the P2P neighbor times out.

  • L1_HOLDTIMER_EXPIRED: indicates that the Level-1 neighbor times out.

  • L2_HOLDTIMER_EXPIRED: indicates that the Level-2 neighbor times out.

  • NEW_L1_ADJ: indicates a new Level-1 neighbor.

  • NEW_L2_ADJ: indicates a new Level-2 neighbor.

  • USGAGE_MISMATCH: indicates that the type of the neighbor is different from that of the Hello message.

  • UPDT_LSP_FAILED: indicates that updating the neighbor status in the LSP fails.

  • NO_MEMORY_FOR_HIGER_PRIORITY_ADJ: indicates that there is no available memory for neighbors with high priorities.

  • DIFFERENT_NET: indicates that the network address of the neighbor changes.

  • P2P_CIRCUIT_ID_CONFLT: indicates that IDs of P2P interfaces conflict.

  • NEW_ADJ: indicates a new P2P neighbor.

  • AREA_MISMATCH: indicates the area address of the neighbor does not match the local area address.

  • 3_WAY_DOWN: indicates that the neighbor is Down during three-way handshake.

  • 3_WAY_INIT: indicates that the neighbor is Init during three-way handshake.

  • 3_WAY_UP: indicates that the neighbor is Up during three-way handshake.

  • P2P_INIT_MEMORY_SHORTAGE: indicates that the memory is not enough and the P2P neighbor is in the init state.

  • PROTOCOL_V4_6_TO_V4: indicates that the neighbor type changes from IPv4 and IPv6 to IPv4.

  • PROTOCOL_V4_6_TO_V6: indicates that the neighbor type changes from IPv4 and IPv6 to IPv6.

  • PROTOCOL_V4_TO_V4_6: indicates that the neighbor type changes from IPv4 to IPv4 and IPv6.

  • PROTOCOL_V6_TO_V4_6: indicates that the neighbor type changes from IPv6 to IPv4 and IPv6.

  • PROTOCOL_V4_TO_V6: indicates that the neighbor type changes from IPv4 to IPv6.

  • PROTOCOL_V6_TO_V4: indicates that the neighbor type changes from IPv6 to IPv4.

  • L1_BFD_DOWN: indicates that Level-1 BFD is Down.

  • L2_BFD_DOWN: indicates that Level-2 BFD is Down.

  • L12_BFD_DOWN: indicates that Level-1-2 BFD is Down.

  • TUNNEL_LEVEL_CHANGE: indicates that the tunnel level changes.

  • TUNNEL_L1_NEW: indicates that a Level-1 tunnel neighbor is generated.

  • TUNNEL_L2_NEW: indicates that a Level-2 tunnel neighbor is generated.

  • TUNNEL_L1_DOWN: indicates the Level-1 tunnel neighbor is Down.

  • TUNNEL_L2_DOWN: indicates the Level-2 tunnel neighbor is Down.

  • TUNNEL_L2_TO_L12: indicates that the neighbor changes from a Level-2 neighbor to a Level-1-2 neighbor.

  • TUNNEL_L1_TO_L12: indicates that the neighbor changes from a Level-1 neighbor to a Level-1-2 neighbor.

  • NEW_ADJ_CREATE: indicates that a new neighbor is generated.

  • NO_COMMON_TOPOLOGY: indicates that the topology information carried in the received Hello message is different from that of the neighbor.

  • REMOTE_IS_PACKET_CHANGED: indicates that the Hello message sent by the remote neighbor changes.

  • NO_SNPA_IN_IIH: indicates that the received Hello message does not contain the SNPA address.

Level

Indicates the neighbor type.

Possible Causes

The IS-IS neighbor changed.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/ALIID_TLV_LEN_SHORT

Message

ISIS/6/ALIID_TLV_LEN_SHORT:ISIS [system-index] ALIAS ID TLV was shorter than valid size. (ValidSize=[UCHAR])

Description

The IS-IS ALIAS ID TLV was too short.

Parameters

Parameter Name Parameter Meaning

[system-index]

Indicates the ISIS system index.

ValidSize

Indicates the length of the TLV.

Possible Causes

The IS-IS ALIAS ID TLV was too short.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/AREA_ADDR_INVALID

Message

ISIS/6/AREA_ADDR_INVALID:ISIS manual area address instance was invalid.

Description

The IS-IS instance with a manually configured area address was invalid.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/AUTH_TLV_OVER_ONECE

Message

ISIS/6/AUTH_TLV_OVER_ONECE:ISIS [process-id] ignored the LSP because the authentication TLV occurred more than one time.

Description

IS-IS ignored the LSP because the authentication TLV appeared for more than one time.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The authentication TLV appeared for more than one time.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/BAD_TLV_LEN

Message

ISIS/6/BAD_TLV_LEN:ISIS [process-id] received an LSP packet with invalid TLV length.

Description

IS-IS received an LSP packet with the TLV of an invalid length.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The length of the TLV in the received LSP packet was incorrect.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/BIND_SOKT_FAIL

Message

ISIS/6/BIND_SOKT_FAIL:ISIS [process-id] failed to bind the socket to the interface [interface-name]. (InterfaceIndex=[STRING], ReturnValue=[ULONG])

Description

IS-IS failed to bind a socket to an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

InterfaceIndex

Indicates the interface index.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to bind a socket to an interface.

Procedure

  1. Check the configuration of the current link.

ISIS/5/CIRC_STATE_SET

Message

ISIS/5/CIRC_STATE_SET:The status of the ISIS [process-id] interface is [interface-state]. (interface=[STRING])

Description

The log message was generated when the IS-IS interface status was changed.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-state]

The status of the IS-IS interface.
  • MTU UP

  • MTU DOWN

  • IP UP

  • IP DOWN

  • LINK UP

  • LINK DOWN

interface

Indicates the name of an interface.

Possible Causes

reset isis all

isis enable

isis ipv6 enable

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/CONFLICT_SYSTEM_ID

Message

ISIS/6/CONFLICT_SYSTEM_ID:ISIS [process-id] maybe detect conflicting System ID.(System ID=[STRING])

Description

IS-IS detected conflicting system IDs.

Parameters

Parameter Name Parameter Meaning
[process-id] Number of the IS-IS process
System ID Conflicting system ID

Possible Causes

Two IS-IS routers in the topology have the same system ID.

Procedure

  1. Change the conflicting system ID.

ISIS/6/CREA_AREA_TLV_FAIL

Message

ISIS/6/CREA_AREA_TLV_FAIL:ISIS [process-id] failed to create the area address TLV option in extended LSP set.

Description

IS-IS failed to create the area address TLV option in extended LSP set.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The LSP fragment mode changed, and the area address TLV option should be created in the LSP.

Procedure

  1. Check the cause of the failure to create the address TLV option in the extended LSP set.

ISIS/6/CREATE_CIRCUIT_FAIL

Message

ISIS/6/CREATE_CIRCUIT_FAIL:ISIS [process-id] failed to create the interface.

Description

IS-IS failed to create the interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/CRT_BFD_SESION_FAIL

Message

ISIS/6/CRT_BFD_SESION_FAIL:ISIS [process-id] failed to create the BFD session with peer [system-id] [level] on the interface. (InterfaceName=[STRING], UserData=[ULONG])

Description

ISIS failed to set up a BFD session with its neighbor on an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[system-id]

Indicates the system ID.

[level]

Indicates the IS-IS level.

InterfaceName

Indicates the name of an interface.

UserData

Indicates the address used to store the data structure of adjacencies.

Possible Causes

Failed to create a BFD session.

Procedure

  1. Run the display diagnostic-information command, save the display of the command, and contact technical support personnel.

ISIS/6/CRT_P2P_ADJ_FAIL

Message

ISIS/6/CRT_P2P_ADJ_FAIL:ISIS [process-id] failed to create the P2P adjacency.

Description

IS-IS failed to create a P2P adjacency.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to create a P2P adjacency.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/DEL_ATTSY_FAIL

Message

ISIS/6/DEL_ATTSY_FAIL:ISIS [process-id] failed to delete the local attached system.

Description

IS-IS failed to delete the locally associated system.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/DEL_BFD_SESSION_FAIL

Message

ISIS/6/DEL_BFD_SESSION_FAIL:ISIS [process-id] failed to delete the BFD session with peer [system-id] [level] on the interface. (InterfaceName=[STRING], UserData=[ULONG])

Description

IS-IS failed to delete the BFD session with its neighbor on an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[system-id]

Indicates the system ID.

[level]

Indicates the IS-IS level.

InterfaceName

Indicates the name of an interface.

UserData

Indicates the address used to store the data structure of adjacencies.

Possible Causes

Failed to delete a BFD session.

Procedure

  1. Run the display diagnostic-information command, save the display of the command, and contact technical support personnel.

ISIS/6/DEL_LKINFO_CSPF_FAIL

Message

ISIS/6/DEL_LKINFO_CSPF_FAIL:ISIS [process-id] failed to delete the TE link information from CSPF. (ReturnValue=[ULONG], NeighborSystemId=[STRING], NeighborPseudoNodeId=[USHORT], NodeStatus=[USHORT], FragmentNumber=[USHORT])

Description

IS-IS failed to delete TE link information from CSPF.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

ReturnValue

Indicates a returned value.

NeighborSystemId

Indicates the system ID of a neighbor.

NeighborPseudoNodeId

Indicates the pseudo node ID of a neighbor.

NodeStatus

Indicates the status of a node.

FragmentNumber

Indicates the fragment number.

Possible Causes

1. An internal error of the system.

Procedure

  1. Run the display mpls te cspf destination command to check whether there are paths that meet specified restriction conditions.

    • If not, go to Step 2.

    • If so, go to Step 3.

  2. Collect log information and configuration information, and then contact technical support personnel.
  3. This log message is informational only, and no action is required.

ISIS/6/DEL_NTWK_MPLS_FAIL

Message

ISIS/6/DEL_NTWK_MPLS_FAIL:ISIS [process-id] failed to delete the network information in MPLS TE. (ReturnValue=[ULONG])

Description

IS-IS failed to delete network information from MPLS TE.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
ReturnValue Indicates a returned value.

Possible Causes

Failed to delete network information from MPLS TE.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/DEL_SUMMRT_URT_FAIL

Message

ISIS/6/DEL_SUMMRT_URT_FAIL:ISIS [process-id] failed to delete the NULL0 route from the URT for summary. (MTID=[USHORT])

Description

IS-IS failed to delete the null 0 summarized route from the URT.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-S process.
MTID Indicates the ID of a topology.

Possible Causes

Failed to delete the null 0 summarized route from the URT.

Procedure

  1. Check the current routing information.

ISIS/6/DISABL_RT_FAIL

Message

ISIS/6/DISABL_RT_FAIL:ISIS [process-id] failed to disable ISIS IP route on the interface [interface-name].

Description

IS-IS failed to disable IS-IS IP routing on the interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

An internal error of the system.

Procedure

  1. Check the status of the route on the interface.

ISIS/6/DISABLE_ROUTELEAK_V6

Message

ISIS/6/DISABLE_ROUTELEAK_V6:ISIS [process-id] failed to disable IPv6 route leaking.

Description

IS-IS failed to disable IPv6 route leaking.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/DYNC_NAME_FAIL

Message

ISIS/6/DYNC_NAME_FAIL:ISIS [process-id] failed to create the dynamic hostname TLV.

Description

ISIS failed to create a dynamic hostname TLV.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Memory allocation failed.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/EN_TE_FAIL_NO_RTID

Message

ISIS/6/EN_TE_FAIL_NO_RTID:ISIS [process-id] failed to enable TE because no router ID is configured.

Description

IS-IS failed to enable TE because no router ID is configured.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to obtain the router ID.

Procedure

  1. Check the status of the switch.

ISIS/6/ENABLE_TE_LV1_FAIL

Message

ISIS/6/ENABLE_TE_LV1_FAIL:ISIS [process-id] failed to enable TE for Level-1.

Description

IS-IS failed to enable TE for the Level-1 interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to enable TE for the Level-1 interface.

Procedure

  1. Run the display this command in a specified IS-IS process to check whether a NET is configured. If no NET is configured, configure a NET.
  2. Run the traffic-eng command in a specified IS-IS process to re-enable TE.
  3. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/ENABLE_TE_LV2_FAIL

Message

ISIS/6/ENABLE_TE_LV2_FAIL:ISIS [process-id] failed to enable TE for Level-2.

Description

IS-IS failed to enable TE for the Level-2 interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to enable TE for the Level-2 interface.

Procedure

  1. Run the display this command in a specified IS-IS process to check whether a NET is configured. If no NET is configured, configure a NET.
  2. Run the traffic-eng command in a specified IS-IS process to re-enable TE.
  3. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/FAIL_CMD_IN_AMB

Message

ISIS/6/FAIL_CMD_IN_AMB:ISIS on the AMB failed to run commands.(FunctionID=[ULONG], DisableFlag=[ULONG])

Description

IS-IS failed to run the command on the AMB.

Parameters

Parameter Name Parameter Meaning

FunctionID

Indicates the ID of the command line.

DisableFlag

Indicates the identifier of disabling the command line.

Possible Causes

This log message was caused by an unpredictable reason.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/6/FAIL_CMD_IN_SMB

Message

ISIS/6/FAIL_CMD_IN_SMB:ISIS on the SMB failed to run commands.(FunctionID=[ULONG], DisableFlag=[ULONG])

Description

IS-IS failed to run the command on the SMB.

Parameters

Parameter Name Parameter Meaning
FunctionID Indicates the ID of the command line.
DisableFlag Indicates the identifier of disabling the command line.

Possible Causes

IS-IS failed to run the command line on the SMB.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/6/FAIL_CRT_OPT_DYN_NM

Message

ISIS/6/FAIL_CRT_OPT_DYN_NM:ISIS [process-id] failed to create the option for dynamic host name.

Description

IS-IS failed to create the dynamic host name option.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/FAIL_SEND_DICT

Message

ISIS/6/FAIL_SEND_DICT:ISIS [process-id] failed to send protocol dictionary to the low layer.(InterfaceIndex=[STRING])

Description

IS-IS failed to deliver the protocol dictionary.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
InterfaceIndex Indicates the interface index.

Possible Causes

Processing the protocol dictionary failed.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/6/FAIL_TRANS_P2P_CSNP

Message

ISIS/6/FAIL_TRANS_P2P_CSNP:ISIS [process-id] failed to transmit P2P CSNP on the interface [interface-name].

Description

IS-IS failed to transmit P2P CSNP packets on the interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

An error occurred during restart.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/FD_CUR_IFINDEX_FAIL

Message

ISIS/6/FD_CUR_IFINDEX_FAIL:ISIS [process-id] failed to find circuit entry according to the interface index [interface-index].

Description

IS-IS failed to find the link according to the interface index.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-index] Indicates the interface index.

Possible Causes

Failed to find the link according to the interface index.

Procedure

  1. Check information about the specified interface.

ISIS/6/FD_SBNTADDR_BDC_FAIL

Message

ISIS/6/FD_SBNTADDR_BDC_FAIL:ISIS [process-id] failed to find the matched subnet address [subnet-address] in broadcast network.

Description

IS-IS failed to find a matching subnet address in a broadcast network.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[subnet-address] Indicates the subnet address.

Possible Causes

Failed to obtain a subnet address.

Procedure

  1. Check the interface status of the switch.

ISIS/6/FIND_CIRCUIT_FAIL

Message

ISIS/6/FIND_CIRCUIT_FAIL:Failed to find ISIS interface according to the interface index [interface-index].

Description

Failed to find an IS-IS interface according to the interface index.

Parameters

Parameter Name Parameter Meaning

[interface-index]

the interface index.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/FIND_SYSID_FAIL

Message

ISIS/6/FIND_SYSID_FAIL:Failed to find the ISIS process ID. (InterfaceIndex=[STRING])

Description

Failed to find the IS-IS process ID.

Parameters

Parameter Name Parameter Meaning
InterfaceIndex Indicates the interface index.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/FLO_LSP_OLO_FAIL

Message

ISIS/6/FLO_LSP_OLO_FAIL:ISIS [process-id] failed to flood the LSP with overload bit set.

Description

IS-IS failed to flood the LSP with the overload bit.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to flood the LSP with the overload bit.

Procedure

  1. Run the display memory-usage command to check the memory usage.
  2. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/FT_GT_RT_URM_FAIL

Message

ISIS/6/FT_GT_RT_URM_FAIL:ISIS [process-id] failed to obtain the route entry [route] from URM. (RouteEntryTable=[ULONG], EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to obtain a routing entry from URM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[route]

Indicates a route.

RouteEntryTable

Indicates a routing table.

EntryId

Indicates the number of a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to obtain a routing entry from URM.

Procedure

  1. Check the current routing information.

ISIS/6/GEN_ATT_LSP_FAIL

Message

ISIS/6/GEN_ATT_LSP_FAIL:ISIS [process-id] failed to generate an LSP with the ATT bit being set.

Description

IS-IS failed to generate an LSP with the ATT bit.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to generate an LSP with the ATT bit.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/GENLSPDESC_FAILSMB

Message

ISIS/4/GENLSPDESC_FAILSMB:ISIS [process-id] failed to generate the Level-[level] LSP fragment on the slave board. (LspId=[STRING], SeqNo=[ULONG])

Description

The IS-IS process on the slave board failed to originate the LSP fragment.

Parameters

Parameter Name Parameter Meaning

[process-id]

indicates the ID of an IS-IS process.

[level]

indicates the IS-IS level.
  • 1: Level-1

  • 2: Level-2

LspId

indicates the ID of an LSP.

SeqNo

indicates the sequence number of an LSP.

Possible Causes

1. The slave board cannot find the corresponding LSP fragment.

2. Failed to allocate memory for the fragment data structure.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/GET_IF_FAILSMB

Message

ISIS/6/GET_IF_FAILSMB:ISIS [process-id] failed to obtain the interface according to the interface index on the slave board. (InterfaceIndex=[STRING], MessageType=[STRING])

Description

The IS-IS process on the slave board failed to obtain the interface according to the interface index.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

InterfaceIndex

Indicates the interface index.

MessageType

Indicates the message type of LSPs:
  • Self LSP: indicates the self-originated LSPs.

  • Other LSP: indicates other LSPs.

  • AdjDelete: indicates neighbor information is deleted.

  • AdjHello: indicates the Hello message received by the slave board.

  • CircDis: indicates DIS information.

Possible Causes

1. The current interface on the slave board was inconsistent with the interface on the main board.

2. The backup interface index was incorrect.

Procedure

  1. Run the display rm interface command to check whether the interface index on the main board is the same as that in the log.

    • If so, go to Step 3.

    • If not, go to Step 2.

  2. (Restart with caution.) You can restart the interface if services are not affected.

    • If so, go to Step 3.

    • If not, go to Step 4.

  3. Collect log information and configuration information, and then contact technical support personnel.
  4. End.

ISIS/6/GET_IFINSTN_ID_FAIL

Message

ISIS/6/GET_IFINSTN_ID_FAIL:Failed to obtain interface instance ID according to the alias.

Description

Failed to obtain the ID of the instance on the interface through the alias.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

Failed to obtain the ID of the instance on the interface through the alias.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GET_IFNET_BY_ALIAS

Message

ISIS/6/GET_IFNET_BY_ALIAS:Failed to obtain IFNET through alias.

Description

Failed to obtain IFNET through the alias.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GET_LINKINFO_FAIL

Message

ISIS/6/GET_LINKINFO_FAIL:ISIS [process-id] failed to obtain link information. (InterfaceIndex=[STRING])

Description

IS-IS failed to obtain link information.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
InterfaceIndex Indicates the interface index.

Possible Causes

Failed to obtain link information.

Procedure

  1. Check the configuration of the interface.

ISIS/6/GT_ACTVE_RT_RM_FAIL

Message

ISIS/6/GT_ACTVE_RT_RM_FAIL:ISIS [process-id] failed to obtain active route from RM. (MTID=[USHORT])

Description

IS-IS failed to obtain an active route from RM.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
MTID Indicates the ID of a topology.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GT_CIRC_IFINDX_FAIL

Message

ISIS/6/GT_CIRC_IFINDX_FAIL:ISIS [process-id] failed to obtain the circuit entry according to the interface index [interface-index].

Description

IS-IS failed to find an interface according to the interface index.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-index] Indicates the interface index.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GT_CIRCINDEX_FAIL

Message

ISIS/6/GT_CIRCINDEX_FAIL:ISIS [process-id] failed to obtain interface number [interface-name].

Description

IS-IS failed to obtain the interface number.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

An internal error of the system.

Procedure

  1. Check the configuration of the current interface.

ISIS/6/GT_INFO_RDM_FAIL

Message

ISIS/6/GT_INFO_RDM_FAIL:ISIS [process-id] failed to obtain information from RDM. (InterfaceIndex=[STRING])

Description

IS-IS failed to obtain information from URM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

InterfaceIndex

Indicates the interface index.

Possible Causes

Failed to obtain information from URM.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GT_ININDEX_FAIL

Message

ISIS/6/GT_ININDEX_FAIL:ISIS [process-id] failed to obtain interface index [interface-index].

Description

IS-IS failed to obtain an interface number.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-index] Indicates the interface index.

Possible Causes

Failed to obtain an interface number.

Procedure

  1. Check the status of the interface.

ISIS/6/GT_LGC_PHY_FAIL

Message

ISIS/6/GT_LGC_PHY_FAIL:ISIS [process-id] failed to obtain the primary logical index [logical-index] through physical index [physical-index].

Description

IS-IS failed to obtain a logical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[logical-index] Indicates the logical interface number.
[physical-index] Indicates the physical interface number.

Possible Causes

Failed to obtain a logical interface.

Procedure

  1. Check the physical interface.

ISIS/6/GT_LGCIF_V6ADDR_FAIL

Message

ISIS/6/GT_LGCIF_V6ADDR_FAIL:ISIS [process-id] failed to obtain logical index [logical-index] from IPv6 link local address [ipv6-address].

Description

IS-IS failed to obtain the logical index from an IPv6 link-local address.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[logical-index] Indicates the logical interface number.
[ipv6-address] Indicates an IPv6 address.

Possible Causes

Failed to obtain the logical index from an IPv6 link-local address.

Procedure

  1. Check the configuration of the local IP address.

ISIS/6/GT_LGCL_SUBNET_FAIL

Message

ISIS/6/GT_LGCL_SUBNET_FAIL:ISIS [process-id] failed to obtain the logical index for local subnet while matching the nexthop address [nexthop]. (PhysicalIndex=[ULONG])

Description

IS-IS failed to obtain the logical index for the local subnet when matching the next hop address.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[nexthop]

Indicates the IP address of the next hop.

PhysicalIndex

Indicates the physical interface number.

Possible Causes

Failed to obtain the logical index for the local subnet.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/GT_LV_RT_URM_FAIL

Message

ISIS/6/GT_LV_RT_URM_FAIL:ISIS [process-id] failed to obtain Level-[level] route entry [route] from URM. (RouteEntryTable=[ULONG], EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to obtain a routing entry from URM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[level]

Indicates the IS-IS level.

[route]

Indicates a route.

RouteEntryTable

Indicates a routing table.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to obtain a routing entry from URM.

Procedure

  1. Check the current routing information.

ISIS/6/GT_LV_RT_V6_URM_FAIL

Message

ISIS/6/GT_LV_RT_V6_URM_FAIL:ISIS [process-id] failed to obtain Level-[level] IPv6 route entry [route] from URM. (RouteEntryTable=[ULONG], EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to obtain an IPv6 routing entry from URM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[level]

Indicates the IS-IS level.

[route]

Indicates a route.

RouteEntryTable

Indicates a routing table.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to obtain an IPv6 routing entry from URM.

Procedure

  1. Check the current routing information.

ISIS/6/GT_MPLSTE_RM_FAIL

Message

ISIS/6/GT_MPLSTE_RM_FAIL:ISIS [process-id] failed to obtain MPLS TE status from RM.

Description

IS-IS failed to obtain the MPLS TE status from RM.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to obtain the TE status.

Procedure

  1. Run the display current-configuration configuration mpls command to check the MPLS TE configuration.

ISIS/6/GT_PHYIF_IFNET_FAIL

Message

ISIS/6/GT_PHYIF_IFNET_FAIL:ISIS [process-id] failed to obtain physical index from the interface [interface-name].

Description

IS-IS failed to obtain the physical index from an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

Failed to obtain the physical index from an interface.

Procedure

  1. Check the physical interface.

ISIS/6/GT_RTENTRY_URM_FAIL

Message

ISIS/6/GT_RTENTRY_URM_FAIL:ISIS [process-id] failed to obtain the route entry from URM. (EntryId=[ULONG], MTID=[USHORT])

Description

IS-IS failed to obtain a routing entry from URM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

EntryId

Indicates the ID of an entry.

MTID

Indicates the ID of a topology.

Possible Causes

Failed to obtain a routing entry from URM.

Procedure

  1. Check the current routing information.

ISIS/6/GT_RTID_RM_FAIL

Message

ISIS/6/GT_RTID_RM_FAIL:ISIS [process-id] failed to obtain router ID from RM. (RouterId=[ULONG])

Description

IS-IS failed to obtain the router ID from RM.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

RouterId

Indicates the ID of a switch.

Possible Causes

Failed to obtain the router ID from RM.

Procedure

  1. Check the router ID again.

ISIS/6/GT_TELK_INFO_FAIL

Message

ISIS/6/GT_TELK_INFO_FAIL:ISIS [process-id] failed to obtain TE link information. (InterfaceNumber=[STRING])

Description

IS-IS failed to obtain TE link information.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

InterfaceNumber

Indicates the number of an interface.

Possible Causes

Failed to obtain TE information.

Procedure

  1. Retry to obtain TE information.

ISIS/6/GT_V6_PHYIF_FAIL

Message

ISIS/6/GT_V6_PHYIF_FAIL:ISIS [process-id] failed to obtain the IPv6 physical index [physical-index] from the interface. (InterfaceIndex=[STRING])

Description

IS-IS failed to obtain the IPv6 physical index from an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[physical-index]

Indicates the physical interface number.

InterfaceIndex

Indicates the interface index.

Possible Causes

Failed to obtain the IPv6 physical index from an interface.

Procedure

  1. Check the current status of the interface.

ISIS/6/GT_V6ADDR_PHYIF_FAIL

Message

ISIS/6/GT_V6ADDR_PHYIF_FAIL:ISIS [process-id] failed to obtain the IPv6 link local address [ipv6-address] from the physical interface [physical-interface].

Description

IS-IS failed to obtain the IPv6 link-local address from a physical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[ipv6-address] Indicates an IPv6 address.
[physical-interface] Indicates the physical interface number.

Possible Causes

Failed to obtain the IPv6 link-local address from a physical interface.

Procedure

  1. Check the current status of the interface.

ISIS/6/IF_TEMP

Message

ISIS/6/IF_TEMP:The interface was a temporary interface. (IsisProcessId=[USHORT], InterfaceIndex=[STRING])

Description

The interface was a temporary interface.

Parameters

Parameter Name Parameter Meaning

IsisProcessId

Indicates the ID of an IS-IS process.

InterfaceIndex

Indicates the interface index.

Possible Causes

An internal error of the system.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/IMPORT_LIMIT_EXCEED

Message

ISIS/4/IMPORT_LIMIT_EXCEED:ISIS [process-id] The number of level-[level] imported routes has exceeded the maximum limit. (sysMTIndex=[USHORT], sysMaxLimit=[ULONG], sysTotalRedist=[ULONG])

Description

The number of external routes imported to an IS-IS area exceeded the maximum limit.

Parameters

Parameter Name Parameter Meaning
[process-id] ID of an IS-IS process
[level] IS-IS level
sysMTIndex Topology ID
sysMaxLimit Maximum number of routes that can be imported
sysTotalRedist Number of imported routes

Possible Causes

The number of external routes imported to the IS-IS process exceeded the maximum limit configured for advertising routes.

Procedure

  1. Delete some imported routes.

ISIS/4/IMPORT_LIMIT_RESTORE

Message

ISIS/4/IMPORT_LIMIT_RESTORE:ISIS [process-id] The number of level-[level] imported routes is restored to less than or equal to the maximum limit. (sysMTIndex=[USHORT], sysMaxLimit=[ULONG], sysTotalRedist=[ULONG])

Description

The number of imported routes in an IS-IS process fell below the maximum limit.

Parameters

Parameter Name Parameter Meaning
[process-id] ID of an IS-IS process
[level] IS-IS level
sysMTIndex Topology ID
sysMaxLimit Maximum number of routes that can be imported
sysTotalRedist Number of imported routes

Possible Causes

The number of imported routes in the IS-IS area fell below the maximum limit.

Procedure

  1. This log is informational only, and no action is required.

ISIS/6/INIT_DEC_FAIL

Message

ISIS/6/INIT_DEC_FAIL:ISIS [process-id] failed to initialize the decision module.

Description

IS-IS failed to initialize the decision module.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Failed to initialize the decision module.

Procedure

  1. If services are not affected, no action is required.
  2. If services are affected, Collect log information and configuration information, and then contact technical support personnel.

ISIS/4/INT_BUILDRUN_FAIL

Message

ISIS/4/INT_BUILDRUN_FAIL:ISIS failed to buildrun for interface [STRING], operate code=[USHORT], return value=[USHORT].

Description

IS-IS failed to generate the Build Run information of the interface.

Parameters

Parameter Name Parameter Meaning

[STRING]

Indicates the name of the interface.

[USHORT]

The value of operate code.
  • 1: To obtain the number of the interface index.
  • 2: To obtain the name of the interface.

[USHORT]

Indicates the return value of the operation.

Possible Causes

Failed to obtain the interface.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/INTI_ISIS_FAIL

Message

ISIS/6/INTI_ISIS_FAIL:ISIS [process-id] failed to initialize ISIS protocol modules.

Description

IS-IS failed to initialize IS-IS protocol modules.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

An internal error of the system.

Procedure

  1. If services are not affected, no action is required.
  2. If services are affected, Collect log information and configuration information, and then contact technical support personnel.

ISIS/3/INVALID_DSTEMOD

Message

ISIS/3/INVALID_DSTEMOD:IS-IS obtained incorrect information about the DS-TE mode from RM. (ProcessId=[USHORT], ModeInfo=[ULONG])

Description

IS-IS obtained incorrect DS-TE mode information from the RM.

Parameters

Parameter Name Parameter Meaning

ProcessId

Indicates the ID of an IS-IS process.

ModeInfo

Indicates the DS-TE mode.

Possible Causes

1. An error occurred in the callback function between IS-IS and the RM.

2. An error occurred in MPLS processing.

Procedure

  1. Re-configure the DS-TE mode in the MPLS view. Check whether the corresponding log is displayed.

    • If IS-IS successfully obtains the DS-TE mode information, go to Step 2.

    • If IS-IS fails to obtain the information after several reconfigurations, go to Step 3.

  2. Services are not affected, and no action is required.
  3. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/INVID_DR_CHANGE

Message

ISIS/6/INVID_DR_CHANGE:The DIS change event is invalid. (IsisProcessId=[USHORT])

Description

The DIS change event was invalid.

Parameters

Parameter Name Parameter Meaning

IsisProcessId

Indicates the ID of an IS-IS process.

Possible Causes

The DR change event was invalid.

Procedure

  1. Check why the DIS change event was invalid.

ISIS/6/INVID_TLV_TYPE_REP

Message

ISIS/6/INVID_TLV_TYPE_REP:ISIS failed to replace the old TLV because TLV type is invalid. (IsisProcessId=[USHORT])

Description

IS-IS failed to replace the old TLV because the TLV type was invalid.

Parameters

Parameter Name Parameter Meaning

IsisProcessId

Indicates the ID of an IS-IS process.

Possible Causes

IS-IS failed to replace the old TLV because the TLV type was invalid.

Procedure

  1. Check the TLV type.

ISIS/5/ISIS_LSP_SEQ_THRESHOLD_EXCEED

Message

ISIS/5/ISIS_LSP_SEQ_THRESHOLD_EXCEED: The LSP sequence number has exceeded the upper threshold value. (isisSysInstance=[USHORT], isisSysLevelIndex=[USHORT], isisPduLspId=[STRING], srcMac=[STRING], recvFromIf=[STRING], thresholdValue=[STRING], LocalSeqNum=[STRING], RemoteSeqNum=[STRING])

Description

The LSP sequence number exceeded the upper alarm threshold.

Parameters

Parameter Name Parameter Meaning

isisSysInstance

ID of an IS-IS process

isisSysLevelIndex

IS-IS level

isisPduLspId

LSP ID

srcMac

Source MAC address of the received LSP

recvFromIf

Name of the interface that received the LSP

thresholdValue

Upper alarm threshold, which is 0xF0000000.

LocalSeqNum

Local sequence number

RemoteSeqNum

Remote sequence number

Possible Causes

Cause 1: The sequence numbers increase to the upper alarm threshold as expected.

Cause 2: An attacker simulated a locally generated LSP, set its sequence number to a value that is greater than the upper alarm threshold, and sent the LSP to the local device.

Cause 3: Another device on the network had the same IS-IS System ID as the local one.

Procedure

  1. Run the display isis lsdb command to check the sequence numbers of locally generated LSPs.

    • If the sequence numbers increase as expected, no action is required.
    • If the sequence numbers increase too fast, go to Step 2.

  2. Run the timer lsp-refresh command in the IS-IS view to increase the LSP update interval and then run the display isis lsdb command to check the sequence numbers of locally generated LSPs.

    • If the sequence numbers increase as expected, go to Step 5.
    • If the sequence numbers increase too fast, go to Step 3.

  3. Check whether there is another device on the network with the local IS-IS System ID.

    • If such a device exists, change its system ID.
    • If no such a device exists, go to Step 4.

  4. Collect alarm information and configuration information, and then contact technical support personnel.
  5. End.

ISIS/6/ISIS_LSP_SEQ_SKIP

Message

ISIS/6/ISIS_LSP_SEQ_SKIP:ISIS modifid self-originated LSP sequence number with received [STRING]. (ProcessId=[USHORT], Level=[USHORT], LspId=[STRING], LocalSeqnum=[ULONG], ReceivedSeqNum=[ULONG], NewSeqNum=[ULONG])

Description

IS-IS modified the sequence number of a self-originated LSP after it received a [UDP]. (ProcessId=[USHORT],Level=[USHORT],LspId=[STRING],LocalSeqnum=[ULONG],ReceivedSeqNum=[ULONG],NewSeqNum=[ULONG])

Parameters

Parameter Name Parameter Meaning

PDU

Received packet

ProcessId

ID of an IS-IS process

Level

Level of an LSP

LspId

ID of the LSP

LocalSeqnum

Sequence number of the local LSP

ReceivedSeqNum

Sequence number of the received packet

NewSeqNum

New sequence number of the LSP

Possible Causes

1. After the IS-IS process restarted, the sequence number increased from one. IS-IS received an LSP whose ID was the same as that of a local LSP, but the sequence number of the received LSP was larger than that of the local one.

2. A system ID conflict existed on the network. As a result, LSPs were updated frequently.

Procedure

  1. Run the display history-command command to check whether the IS-IS process was restarted on the local switch using the reset isis all command.

    • If the IS-IS process was restarted, this log message is informational only, and no action is required.

    • If the IS-IS process was not restarted, go to Step 2.

  2. Run the display isis lsdb command repeatedly to check whether the sequence numbers of LSPs on the local switch increase abnormally fast. Specifically, check whether the LSP update interval is less than that configured using the timer lsp-refresh command.

    • If the LSP update interval is less than the configured one, go to Step 3.

    • If the LSP update interval is not less than the configured one, go to Step 5.

  3. Run the display current-configuration command to check whether another switch has the same system ID or virtual system ID as that of the local switch.

    • If a system ID or virtual system ID conflict exists, go to Step 4.

    • If no system ID or virtual system ID conflict exists, go to Step 5.

  4. Enter the IS-IS view of the local switch or the switch whose system ID or virtual system ID is the same as that of the local switch, run the undo network-entity command to delete the conflicting system ID or run the undo virtual-system command to delete the conflicting virtual system ID, and then run the network-entity command to configure a different system ID or run the virtual-system command to configure a different virtual system ID. Then, check whether the problem is resolved. If the undo network-entity or undo virtual-system command is run, the conflicting system ID or virtual system ID becomes unavailable. Therefore, make sure that the system ID or virtual system ID conflict exists before you run the undo network-entity or undo virtual-system command.

    • If the problem is resolved, go to Step 6.

    • If the problem persists, go to Step 5.

  5. Collect log information and configuration information, and then contact technical support personnel.
  6. End.

ISIS/6/JN_MTCAST_ADDR_FAIL

Message

ISIS/6/JN_MTCAST_ADDR_FAIL:Failed to join the multicast group. (InterfaceIndex=[STRING], ReturnValue=[LONG])

Description

Failed to join a multicast group.

Parameters

Parameter Name Parameter Meaning

InterfaceIndex

Indicates the interface index.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to join a multicast group.

Procedure

  1. Check the configuration of the interface.

ISIS/6/JOIN_L1_ADDR_FAIL

Message

ISIS/6/JOIN_L1_ADDR_FAIL:ISIS [process-id] failed to join all Level-1 multicast group for the interface [interface-name].

Description

IS-IS failed to join any Level-1 multicast group on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

Failed to join a multicast group.

Procedure

  1. Check the configuration of the current link.

ISIS/6/JOIN_L2_ADDR_FAIL

Message

ISIS/6/JOIN_L2_ADDR_FAIL:ISIS [process-id] failed to join all Level-2 multicast group for the interface [interface-name].

Description

IS-IS failed to join any Level-2 multicast group on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

Failed to join a multicast group.

Procedure

  1. Check the configuration of the current link.

ISIS/6/JOIN_ALLIS_ADDR_FAIL

Message

ISIS/6/JOIN_ALLIS_ADDR_FAIL:ISIS [process-id] failed to join ALLIS multicast group for the interface [interface-name].

Description

IS-IS failed to join multicast groups on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of the interface.

Possible Causes

Failed to call the socket function.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/6/L3VPN_FRR_CHANGE

Message

ISIS/6/L3VPN_FRR_CHANGE:L3VPN notified IS-IS that FRR changed.(VrfId=[USHORT])

Description

L3VPN notified IS-IS of the change of the Fast Reroute (FRR).

Parameters

Parameter Name Parameter Meaning

VrfId

Indicates the ID of the Virtual Route Forwarding (VRF).

Possible Causes

The ip frr route-policy route-policy-name command was run in the system view to enable IP FRR of the public network.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/LDP_INFORM_RM_ENAB

Message

ISIS/6/LDP_INFORM_RM_ENAB:IS-IS [process-id] informed RM that ldp-sync was enabled interface [interface-name].

Description

IS-IS notified the RM that LDP synchronization was enabled on the interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

IS-IS and LDP synchronization was enabled.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/LDP_SYNC_STATE_CHG

Message

ISIS/5/LDP_SYNC_STATE_CHG:An interface of the ISIS process [process-id] is changed from the ldp-sync-[SyncPreviousState] state to the ldp-sync-[SyncCurrentState] state. (IfName=[STRING])

Description

The IS-IS-LDP synchronization status changed on an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

ID of an IS-IS process

[SyncPreviousState]

IS-IS-LDP synchronization status before the change

[SyncCurrentState]

IS-IS-LDP synchronization status after the change

IfName

Name of an interface

Possible Causes

The IS-IS-LDP synchronization status changed on an interface.

Procedure

  1. Run the display isis ldp-sync interface command in any view to check the Sync State and LDP State fields.
  2. Check whether the Sync State field fails to reach the Sync-Achieved state within a long period (more than 10 minutes).

    • If so, go to step 2.

    • If no, go to step 6.

  3. Check whether the LDP session is Down.

    • If so, go to step 4.

    • If no, go to step 5.

  4. Refer to the solution to the mplsLdpSessionDown alarm.

    • If the problem persists, go to step 5.

    • If the fault is rectified, go to step 6.

  5. Collect log information and configuration information, and then contact technical support personnel.
  6. End.

ISIS/6/LEAVE_L1_ADDR_FAIL

Message

ISIS/6/LEAVE_L1_ADDR_FAIL:ISIS [process-id] failed to leave all Level-1 multicast group on the circuit [interface-name].

Description

IS-IS failed to leave any Level-1 multicast group on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

Failed to leave a multicast group.

Procedure

  1. Check the configuration of the current link.

ISIS/6/LEAVE_L2_ADDR_FAIL

Message

ISIS/6/LEAVE_L2_ADDR_FAIL:ISIS [process-id] failed to leave all Level-2 multicast group on the circuit [interface-name].

Description

IS-IS failed to leave any Level-2 multicast group on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of an interface.

Possible Causes

Failed to leave a multicast group.

Procedure

  1. Check the configuration of the current link.

ISIS/6/LEAVE_ALLIS_ADDR_FAIL

Message

ISIS/6/LEAVE_ALLIS_ADDR_FAIL:ISIS [process-id] failed to leave ALLIS multicast group on the circuit [interface-name].

Description

IS-IS failed to leave multicast groups on an interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[interface-name] Indicates the name of the interface.

Possible Causes

Failed to call the socket function.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

ISIS/5/LOCALSYS_DIS_REST_RT

Message

ISIS/5/LOCALSYS_DIS_REST_RT:Local system was DIS among ISIS restarted capable routers.

Description

The local system was elected as the DIS among switch enabled with IS-IS GR.

Parameters

Parameter Name Parameter Meaning
None. None.

Possible Causes

The IIH packet in which the restart TLV has the RA bit was received during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/LV_MTCAST

Message

ISIS/6/LV_MTCAST:ISIS leaves multicast groups because ISIS received packet on unknown interface [interface-name].

Description

IS-IS left a multicast group because IS-IS received a packet on an unknown interface.

Parameters

Parameter Name Parameter Meaning
[interface-name] Indicates the name of an interface.

Possible Causes

Received a packet on an unknown interface.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/LV_MTCAST_ADDR_FAIL

Message

ISIS/6/LV_MTCAST_ADDR_FAIL:Failed to leave the multicast group. (InterfaceIndex=[STRING], ReturnValue=[LONG])

Description

Failed to leave a multicast group.

Parameters

Parameter Name Parameter Meaning

InterfaceIndex

Indicates the interface index.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to leave a multicast group.

Procedure

  1. Check the configuration of the interface.

ISIS/6/MATCH_CIRC_FAIL

Message

ISIS/6/MATCH_CIRC_FAIL:ISIS [process-id] failed to match interface address. (InterfaceIndex=[STRING])

Description

IS-IS failed to match an interface address.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

InterfaceIndex

Indicates the interface index.

Possible Causes

Failed to match an interface address.

Procedure

  1. Reconfigure the interface address.

ISIS/6/MD_LV_RT_FAIL

Message

ISIS/6/MD_LV_RT_FAIL:ISIS [process-id] failed to modify Level-[level] route entry [route]. (EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to change a routing entry.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[level]

Indicates the IS-IS level.

[route]

Indicates a route.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a return value.

Possible Causes

Failed to change a routing entry.

Procedure

  1. Check the current routing information.

ISIS/6/MD_LV_RT_V6_FAIL

Message

ISIS/6/MD_LV_RT_V6_FAIL:ISIS [process-id] failed to modify Level-[level] IPv6 route entry [route]. (EntryId=[ULONG], MTID=[USHORT], ReturnValue=[STRING])

Description

IS-IS failed to change an IPv6 routing entry.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[level]

Indicates the IS-IS level.

[route]

Indicates a route.

EntryId

Indicates a routing entry.

MTID

Indicates the ID of a topology.

ReturnValue

Indicates a return value.

Possible Causes

Failed to change an IPv6 routing entry.

Procedure

  1. Check the current routing information.

ISIS/6/MDF_LKINFO_CSPF_FAIL

Message

ISIS/6/MDF_LKINFO_CSPF_FAIL:ISIS [process-id] failed to modify TE link information to CSPF. (ReturnValue=[ULONG], NeighborSystemId=[STRING], NeighborPseudoNodeId=[USHORT], NodeStatus=[USHORT], FragmentNumber=[USHORT])

Description

IS-IS failed to modify TE link information in CSPF.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

ReturnValue

Indicates a returned value.

NeighborSystemId

Indicates the system ID of a neighbor.

NeighborPseudoNodeId

Indicates the pseudo node ID of a neighbor.

NodeStatus

Indicates the status of a node.

FragmentNumber

Indicates the fragment number.

Possible Causes

1. An internal error of the system.

2. CSPF was not enabled.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/MDF_NTWK_MPLS_FAIL

Message

ISIS/6/MDF_NTWK_MPLS_FAIL:ISIS [process-id] failed to modify network information in MPLS TE. (ReturnValue=[ULONG])

Description

IS-IS failed to modify network information in MPLS TE.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to modify network information in MPLS TE.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/MTU_EXCEED_MAXPDU

Message

ISIS/6/MTU_EXCEED_MAXPDU:The MTU size [mtu-size] exceeded the maximum PDU size [pdu-size], and set the MTU to the maximum PDU size. (IsisProcessId=[USHORT], InterfaceIndex=[STRING])

Description

The MTU size exceeded the maximum PDU size, and was set to the maximum PDU size.

Parameters

Parameter Name Parameter Meaning
[mtu-size] Indicates the size of the MTU.
[pdu-size] Indicates the size of the PDU.
IsisProcessId Indicates the ID of an IS-IS process.
InterfaceIndex Indicates the interface index.

Possible Causes

The size of the MTU was too large.

Procedure

  1. Reconfigure the size of the MTU.

ISIS/6/NSR_MSG_PROC

Message

ISIS/6/NSR_MSG_PROC:ISIS received a message from RM. TaskID is [task-id], MsgType is [message-type], NSR configuration is [nsr-status].

Description

During NSR, the IS-IS process received a message.

Parameters

Parameter Name Parameter Meaning

[task-id]

indicates the task ID.

[message-type]

indicates the message type.

[nsr-status]

indicates the NSR status.
  • 0: indicates that NSR is not configured.

  • 1: indicates that NSR is configured.

Possible Causes

RM instructed IS-IS to enable NSR, perform backup, and smooth configurations.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/NSR_STATE_CHANGE

Message

ISIS/6/NSR_STATE_CHANGE:ISIS on the slave board received the message that NSR was enabled.

Description

ISIS on the slave board received the message that NSR was enabled.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

Global data was backed up on the slave board when NSR was enabled.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/P2P_CIRC_TX_LSP_FAIL

Message

ISIS/6/P2P_CIRC_TX_LSP_FAIL:ISIS [process-id] failed to transmit LSP on the p2p circuit. (CircuitName=[string])

Description

IS-IS failed to transmit LSPs on a P2P link.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
CircuitName Indicates the name of an interface.

Possible Causes

Failed to transmit LSPs on a P2P interface.

Procedure

  1. Check information about the current packet.

ISIS/4/PEER_DOWN_BFDDOWN

Message

ISIS/4/PEER_DOWN_BFDDOWN:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the BFD node was down. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the BFD node became Down.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The BFD node became Down, and the IS-IS neighbor went Down.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/PEER_DOWN_CIRC_DOWN

Message

ISIS/4/PEER_DOWN_CIRC_DOWN:ISIS [process-id] neighbor [neighbor] was down because interface [interface-name] was Down. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down because the interface became Down.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

1. The shutdown command was run on the interface.

2: Abnormality occurred on the interface.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 3.
  2. Run the display rm interface verbose command and save the command output; contact technical support personnel.
  3. End.

ISIS/4/PEER_DOWN_DIS_CHANGE

Message

ISIS/4/PEER_DOWN_DIS_CHANGE:IS-IS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the DIS changed. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local switch sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the Designated Intermediate System (DIS) changed.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The DIS of the broadcast network changed, and the IS-IS neighbor went Down.

Procedure

  1. If a small number of logs are generated, wait for a while to see whether the normal state is entered. If so, no action is required.
  2. If a large number of logs are generated, contact technical support personnel.

ISIS/4/PEER_DOWN_LOW_MEMORY

Message

ISIS/4/PEER_DOWN_LOW_MEMORY:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because memory was not enough. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type]; CPU usage was [cpu-percent]%.

Description

The IS-IS neighbor went Down on the interface because the memory was insufficient.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

[cpu-percent] Indicates the CPU usage.

Possible Causes

The insufficient memory caused the IS-IS neighbor to become Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DOWN_NO_MEMORY

Message

ISIS/4/PEER_DOWN_NO_MEMORY:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the memory of RM was not enough. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type];CPU usage was [cpu-percent]%.

Description

The IS-IS neighbor went Down on the interface because the RM memory was insufficient.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

[cpu-percent] Indicates the CPU usage.

Possible Causes

The insufficient RM memory caused the IS-IS neighbor to become Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DOWN_REPTADJ

Message

ISIS/4/PEER_DOWN_REPTADJ:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because a repeated neighbor was found. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because two same neighbors were detected.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

A repeated neighbor was found, and the IS-IS neighbor went Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DOWN_REPTP2PADJ

Message

ISIS/4/PEER_DOWN_REPTP2PADJ:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because repeated P2P neighbors were found. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because two same P2P neighbors were detected.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

Two same P2P neighbors were found, and the IS-IS neighbor went Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DOWN_RPRDOWN

Message

ISIS/4/PEER_DOWN_RPRDOWN:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the RPR node was Down. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [sent-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the RPR node became Down.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[sent-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The RPR node became Down, and the IS-IS neighbor went Down.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/PEER_DWN_ADJ_STATDWN

Message

ISIS/4/PEER_DWN_ADJ_STATDWN:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the adjacency status changed into down. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The adjacency status changed to Down, and the IS-IS neighbor became Down.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The IS-IS neighbor went Down because the adjacency status became Down.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 4.
  2. Check the status of the switches between which the neighbor relationship is established.
  3. Collect log information and configuration information, and then contact technical support personnel.
  4. End.

ISIS/4/PEER_DWN_AREAMISMACH

Message

ISIS/4/PEER_DWN_AREAMISMACH:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because area mismatched. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local switch sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because areas were mismatched.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The area addresses were mismatched, and thus the IS-IS neighbor became Down.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 3.
  2. Run the is-level command to configure proper levels for the two switchs between which the neighbor relationship is established. If the levels are correct, run the network-entity command to reconfigure NET for the switches.
  3. End.

ISIS/4/PEER_DWN_CIRC_SILENT

Message

ISIS/4/PEER_DWN_CIRC_SILENT:ISIS [process-id] neighbor [neighbor] was Down because silent is set on interface [interface-name]. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] Hello packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down because the interface was configured as a silent interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The interface was configured as a silent interface, that is, the interface was suppressed, and thus the IS-IS neighbor went Down.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 3.
  2. Run the undo isis silent command to restore the interface to the default mode.
  3. End.

ISIS/4/PEER_DWN_HLDTMR_EXPR

Message

ISIS/4/PEER_DWN_HLDTMR_EXPR:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because hold timer expired. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type]; CPU usage was [cpu-percent]%.

Description

The IS-IS neighbor went Down on the interface because the Hold timer expired.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

[cpu-percent] Indicates the CPU usage.

Possible Causes

A Hello packet was not received from the neighbor within the time period specified by the Hold timer, and thus the IS-IS neighbor became Down.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 4.
  2. Check the status of the switches between which the neighbor relationship is established.
  3. Collect log information and configuration information, and then contact technical support personnel.
  4. End.

ISIS/4/PEER_DWN_ID_CONFLICT

Message

ISIS/4/PEER_DWN_ID_CONFLICT:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because P2P circuit ID conflict. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface due to the conflicting P2P circuit IDs.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The circuit IDs on the P2P link conflicted, and thus the IS-IS neighbor went Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DWN_LEVEL_CHANG

Message

ISIS/4/PEER_DWN_LEVEL_CHANG:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because adjacency level was changed. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the level of the neighbor changed.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The change of neighbor levels caused the IS-IS neighbor to become Down.

Procedure

  1. Judge whether the neighbor relationship needs to be established on the interface. If so, go to Step 2; if not, go to Step 3.
  2. Run the is-level command to configure proper levels for the two switches between which the neighbor relationship is established.
  3. End.

ISIS/4/PEER_DWN_PDUMISMATCH

Message

ISIS/4/PEER_DWN_PDUMISMATCH:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the PDU mismatched. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the received PDU did not match the local specifications.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The mismatched PDU caused the IS-IS neighbor to become Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_DWN_SYS_DISABLE

Message

ISIS/4/PEER_DWN_SYS_DISABLE:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because ISIS was disabled. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because ISIS was disabled.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

IS-IS was disabled, and thus the IS-IS neighbor went Down.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/PEER_DWN_SYSTYP_UNKN

Message

ISIS/4/PEER_DWN_SYSTYP_UNKN:ISIS [process-id] neighbor [neighbor] was Down on interface [interface-name] because the system type was unknown. The Hello packet was received at [hello-time] last time; the maximum interval for sending Hello packets was [max-interval]; the local router sent [send-number] Hello packets and received [receive-number] packets; the type of the Hello packet was [packet-type].

Description

The IS-IS neighbor went Down on the interface because the system type was unknown.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[neighbor] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.
[hello-time] Indicates the time when a Hello packet was received last time.
[max-interval] Indicates the maximum interval for sending Hello packets.
[send-number] Indicates the number of Hello packets that were sent.
[receive-number] Indicates the number of Hello packets that were received.
[packet-type] Indicates the type of the Hello packet. The type can be
  • P2P: indicates the P2P Hello packet.

  • Lan Level-1: indicates the Hello packet in the Level-1 broadcast network.

  • Lan Level-2: indicates the Hello packet in the Level-2 broadcast network.

Possible Causes

The unknown system type of the neighbor caused the IS-IS neighbor to become Down.

Procedure

  1. Run the display diagnostic-information command and save the command output; contact technical support personnel.

ISIS/4/PEER_FLAPPING_SUPPRESS

Message

ISIS/4/PEER_FLAPPING_SUPPRESS: The status of peer flapping suppress is changed. (Proc=[USHORT], IfName=[STRING], SuppressPreviousStatus=[STRING], SuppressCurrentStatus=[STRING], Reason=[USHORT])

Description

The status of IS-IS neighbor relationship flapping suppression changed on the local interface.

Parameters

Parameter Name Parameter Meaning

Proc

Process ID

IfName

Interface name

SuppressPreviousStatus

Suppression previous status

SuppressCurrentStatus

Suppression current status

Reason

Suppression causes are as follows:
  • 1: The suppression exits because the hold-max-cost timer expires.

  • 2: The suppression exits because the hold-down timer expires.

  • 3: A configuration change occurs.

  • 4: A manual operation is performed to exit from flapping suppression.

  • 5: The neighbor relationship frequently flaps.

  • 6: Suppression is aborted forcibly using the reset isis process-id suppress-flapping peer[interface interface-type interface-number ] notify-peer command on the remote device.

Possible Causes

IS-IS neighbor relationship flapping suppression started, or the interface exited from the suppression.

Procedure

  1. Run the display isis last-peer-change [ process-id | vpn-instance vpn-instance-name ] command to check whether frequent interface flapping occurs.

    • If frequent interface flapping occurs, this trap message is informational only and no action is required.
    • If no frequent interface flapping occurs, go to Step 2.

  2. End.

ISIS/5/PEER_UP_ADJ_CREATE

Message

ISIS/5/PEER_UP_ADJ_CREATE:ISIS process id [process-id] neighbor [system-id] on the interface [interface-name] is up.

Description

IS-IS neighbor is Up.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[system-id] Indicates the system ID of a neighbor.
[interface-name] Indicates the name of an interface.

Possible Causes

IS-IS neighbor is Up.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/PROCESS_TMR_EVENT

Message

ISIS/6/PROCESS_TMR_EVENT:A timer expired when ISIS process was invalid. (TimerEvent=[ULONG], ProcessId=[ULONG])

Description

A timer expired when IS-IS process was invalid.

Parameters

Parameter Name Parameter Meaning

TimerEvent

Indicates the type of a timer.

ProcessId

Indicates the ID of an IS-IS process.

Possible Causes

A timer expired when IS-IS process was invalid.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/ISIS_PURGE_LSP

Message

ISIS/6/ISIS_PURGE_LSP:ISIS purged Lsp. (ProcessId=[USHORT], Level=[USHORT], LspId=[STRING], SeqNum=[ULONG])

Description

IS-IS purged an LSP. (ProcessId=[USHORT], Level=[USHORT], LspId=[STRING], SeqNum=[ULONG])

Parameters

Parameter Name Parameter Meaning

ProcessId

ID of an IS-IS process

Level

Level of an LSP

LspId

ID of the LSP

SeqNum

Sequence number of the LSP

Possible Causes

The lifetime of the LSP expired.

Procedure

  1. If services are not affected, no action is required. If services are affected, record the log information and contact technical support personnel.

ISIS/6/RCV_BFD_DET_EVENT

Message

ISIS/6/RCV_BFD_DET_EVENT:The BFD detection down event was received.

Description

The BFD detect Down event was received.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

A BFD message from the RM was received, which was helpful for locating problems between modules.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/RCV_ERRSELFLSP_SMB

Message

ISIS/4/RCV_ERRSELFLSP_SMB:ISIS [process-id] received an incorrect backup self LSP on the slave board. (LspId=[STRING], Level=[STRING], Reason=[STRING], SeqNum=[STRING], TlvType=[USHORT], TlvLength=[USHORT])

Description

The slave board received the incorrect self-LSP.

Parameters

Parameter Name Parameter Meaning

[process-id]

indicates the ID of an IS-IS process.

LspId

indicates the ID of an LSP.

Level

indicates the IS-IS level.
  • 1: Level-1

  • 2: Level-2

Reason

indicates the cause for the error:
  • Wrong LSP length: indicates that the length of the received LSP is incorrect.

  • Wrong TLV length: indicates that the TLV length is incorrect.

  • Receive reduplicate TLV: indicates that the duplicated TLV is received.

  • Wrong TLV place: indicates that the location of the TLV is incorrect.

  • Encoding after Nbr TLV: indicates that the IS-IS process receives the area address TLV after receiving the NBR TLV.

  • Detect invalid MT ID: indicates that the unavailable MT ID is detected.

  • Wrong TLV format: indicates that the TLV format is incorrect.

  • Unknown TLV type: indicates the unknown TLV type.

  • Had received more than three area address(es): indicates that the IS-IS process has received more than three area addresses.

  • Received too long area address: indicates that the too long area address is received.

  • Received wrong area address length: indicates that the length of the area address TLV is incorrect.

  • Received invalid area address: indicates that the current area address is unavailable.

  • Received more than three area address(es): indicates that there are more than three area addresses in the TLV.

SeqNum

indicates the sequence number of an LSP.

TlvType

indicates the TLV type.

TlvLength

indicates the TLV length.

Possible Causes

The slave board received the incorrect self-LSP.

Procedure

  1. Collect the debugging information and the log to check the contents of the LSP on the slave board and then compare it with the LSP on the main board to locate the fault.

ISIS/6/RCV_NODE_DOWN_EVENT

Message

ISIS/6/RCV_NODE_DOWN_EVENT:The node Down event sent by RPR was received.

Description

A node Down event notified by the RPR was received.

Parameters

Parameter Name Parameter Meaning

None

None

Possible Causes

A BFD message from the RM was received, which was helpful for locating problems between modules.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/RCV_OTHER_PURGED_LSP

Message

ISIS/6/RCV_OTHER_PURGED_LSP:ISIS [USHORT] received a purged LSP. (Level=[USHORT], PduLspId=[STRING], Interface=[STRING], NbrSystem=[STRING], SrcSystem=[STRING], SrcDynName=[STRING], SrcNbrSystem=[STRING])

Description

The IS-IS system received an LSP with Remaining Time 0 (purged LSP) from another system.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the IS-IS process ID.

Level

Indicates the IS-IS level.

PduLspId

Indicates the ID of the purged LSP.

Interface

Indicates the interface that receives the purged LSP.

NbrSystem

Indicates the system ID of a neighbor.

SrcSystem

Indicates the system ID of the device that sends the purged LSP.

SrcDynName

Indicates the dynamic hostname of the device that sends the purged LSP.

SrcNbrSystem

Indicates the neighbor System ID of the device that sends the purged LSP.

Possible Causes

The IS-IS system received a purged LSP from another system.

Procedure

  1. Check whether SrcSystem is available in the log.

    • If SrcSystem is available, check the system ID of the device that sends the purged LSP and go to Step 3.
    • If SrcSystem is unavailable, go to Step 2.

  2. Check NbrSystem in the log, download the log from the neighbor, and check whether the purged LSP was sent by the neighbor.

    • If the purged LPS was sent by the neighbor, go to Step 3.
    • If the purged LPS was not sent by the neighbor, go to Step 4.

  3. Check whether the purged LSP has been deleted from the device that sent it.

    • If the purged LSP has been deleted from the device that sent it, this log message is informational only and no action is required.
    • If the purged LSP has not been deleted from the device that sent it, go to Step 4.

  4. Locate the device that sends the purged LSP and go to Step 3.
  5. Collect log information and configuration information, and then contact technical support personnel.
  6. End.

ISIS/6/RCV_OWN_PURGED_LSP

Message

ISIS/6/RCV_OWN_PURGED_LSP:ISIS [USHORT] received an own purged LSP. (Level=[USHORT], PduLspId=[STRING], Interface=[STRING], NbrSystem=[STRING], SrcSystem=[STRING], SrcDynName=[STRING], SrcNbrSystem=[STRING])

Description

The IS-IS system received an LSP with Remaining Time 0 (purged LSP) from another system, and the LSP was locally generated.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the IS-IS process ID.

Level

Indicates the IS-IS level.

PduLspId

Indicates the ID of the purged LSP.

Interface

Indicates the interface that receives the purged LSP.

NbrSystem

Indicates the system ID of a neighbor.

SrcSystem

Indicates the system ID of the device that sends the purged LSP.

SrcDynName

Indicates the dynamic hostname of the device that sends the purged LSP.

SrcNbrSystem

Indicates the neighbor System ID of the device that sends the purged LSP.

Possible Causes

  • Cause 1: The local device did not update local LSPs in time. As a result, a locally generated LSP aged and was flooded back.

  • Cause 2: The LSP was modified because of a failure, such as a transmission failure. As a result, the LSP became a purged LSP.

  • Cause 3: The local device restarted, or the IS-IS process was reset. As a result, the local device received the purged LSP that was locally generated.

Procedure

  1. Check whether the device restarted.

    • If the device restarted, this log message is informational only and no action is required.
    • If the device did not restart, go to Step 2.

  2. Check whether SrcSystem is available in the log.

    • If SrcSystem is available, check the system ID of the device that sends the purged LSP and go to Step 4.
    • If SrcSystem is unavailable, go to Step 3.

  3. Check NbrSystem in the log, download the log from the neighbor, and check whether the purged LSP was sent by the neighbor.

    • If the purged LPS was sent by the neighbor, go to Step 4.
    • If the purged LPS was not sent by the neighbor, go to Step 5.

  4. Check whether the purged LSP has been deleted from the device that sent it.

    • If the purged LSP has been deleted from the device that sent it, this log message is informational only and no action is required.
    • If the purged LSP has not been deleted from the device that sent it, go to Step 5.

  5. Locate the device that sends the purged LSP and go to Step 4.
  6. Collect log information and configuration information, and then contact technical support personnel.
  7. End.

ISIS/6/RCV_RPR_EVENT

Message

ISIS/6/RCV_RPR_EVENT:The RPR [message-type] event was received.

Description

An RPR event was received.

Parameters

Parameter Name Parameter Meaning
[message-type] Indicates the type of a message. The types of messages are as follows

1) NODE DOWN: indicates a Down node.

2) UNEXPECTED: indicates an unexpected node.

Possible Causes

Received an RPR message from the RM, which was helpful for locating problems between modules.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/RCV_RPRMSG

Message

ISIS/6/RCV_RPRMSG:The RPR message was received from RM. (MessageType=[ULONG], IfnetIndex=[STRING], NodeNumber=[ULONG])

Description

The Resilient Packet Ring (RPR) message was received from the RM.

Parameters

Parameter Name Parameter Meaning

MessageType

Indicates the message type.

IfnetIndex

Indicates the IFNET index.

NodeNumber

Indicates the number of nodes.

Possible Causes

Received an RPR message from the RM, which was helpful for locating problems between modules.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/3/REA_MAX_SEQ_NUM

Message

ISIS/3/REA_MAX_SEQ_NUM: The LSP sequence number almost reaches the maximum value. (isisSysInstance=[USHORT], isisSysLevelIndex=[USHORT], isisPduLspId=[STRING])

Description

The LSP sequence number reached the maximum value.

Parameters

Parameter Name Parameter Meaning

isisSysInstance

ID of an IS-IS process

isisSysLevelIndex

IS-IS level

isisPduLspId

LSP ID

Possible Causes

Cause 1: The sequence numbers increase to the maximum value as expected.

Cause 2: An attacker simulated a locally generated LSP, set its sequence number to the maximum value, and sent the LSP to the local device.

Cause 3: Another device on the network had the same IS-IS System ID as the local one.

Procedure

  1. Run the display isis lsdb command to check the sequence numbers of locally generated LSPs.

    • If the sequence numbers increase as expected, no action is required.
    • If the sequence numbers increase too fast, go to Step 2.

  2. Run the timer lsp-refresh command in the IS-IS view to increase the LSP update interval and then run the display isis lsdb command to check the sequence numbers of locally generated LSPs.

    • If the sequence numbers increase as expected, go to Step 5.
    • If the sequence numbers increase too fast, go to Step 3.

  3. Check whether there is another device on the network with the local IS-IS System ID.

    • If such a device exists, change its system ID.
    • If no such a device exists, go to Step 4.

  4. Collect alarm information and configuration information, and then contact technical support personnel.
  5. End.

ISIS/6/REC_RM_MEM_RESTORE

Message

ISIS/6/REC_RM_MEM_RESTORE:ISIS [process-id] received memory restoration notification from RM.

Description

IS-IS received a notification for memory restoration from the RM.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Memory was restored from shortage to the normal state.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/REC_RM_MEM_SHORT

Message

ISIS/4/REC_RM_MEM_SHORT:ISIS [process-id] received memory shortage notification from RM.

Description

IS-IS received the memory shortage notification from RM.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

Received the memory shortage notification from RM.

Procedure

  1. Run the display memory-usage command to check the memory usage.
  2. Collect log information and configuration information, and then contact technical support personnel.

ISIS/4/REDIST_THRESHOLD_REACH

Message

ISIS/4/REDIST_THRESHOLD_REACH: ISIS [process-id] The number of level-[level] imported routes has reached the upper threshold value. (sysMTIndex=[USHORT], sysMaxLimit=[ULONG], sysUpperThresholdValue=[ULONG], sysLowerThresholdValue=[ULONG], sysTotalRedist=[ULONG])

Description

The number of external routes imported to an IS-IS area reached the alarm upper threshold.

Parameters

Parameter Name Parameter Meaning
[process-id] ID of an IS-IS process
[level] IS-IS level
sysMTIndex Topology ID
sysMaxLimit Maximum number of routes that can be imported
sysUpperThresholdValue Alarm upper threshold
sysLowerThresholdValue Alarm lower threshold
sysTotalRedist Number of imported routes

Possible Causes

The number of external routes imported to the IS-IS area reached the alarm upper threshold.

Procedure

  1. Delete some imported routes.

ISIS/4/REDIST_THRESHOLD_REACH_CLEAR

Message

ISIS/4/REDIST_THRESHOLD_REACH_CLEAR: ISIS [process-id] The number of level-[level] imported routes has been less than the lower threshold value. (sysMTIndex=[USHORT], sysMaxLimit=[ULONG], sysUpperThresholdValue=[ULONG], sysLowerThresholdValue=[ULONG], sysTotalRedist=[ULONG])

Description

The number of external routes imported to an IS-IS area fell below the alarm lower threshold.

Parameters

Parameter Name Parameter Meaning
[process-id] ID of an IS-IS process
[level] IS-IS level
sysMTIndex Topology ID
sysMaxLimit Maximum number of routes that can be imported
sysUpperThresholdValue Alarm upper threshold
sysLowerThresholdValue Alarm lower threshold
sysTotalRedist Number of imported routes

Possible Causes

The number of external routes imported to the IS-IS area fell below the alarm lower threshold.

Procedure

  1. This log is informational only, and no action is required.

ISIS/6/RM_CIRC_CHANGE

Message

ISIS/6/RM_CIRC_CHANGE:ISIS [process-id] failed to send the message that the physical interface changed.

Description

IS-IS failed to send the message that reported the change of the physical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS failed to send the message that reported the change of the physical interface.

Procedure

  1. If a small number of logs are generated, wait for a while to see whether the normal state is entered. If so, no action is required.
  2. If a large number of logs are generated, contact technical support personnel.

ISIS/6/RM_CIRC_CHANGE_V6

Message

ISIS/6/RM_CIRC_CHANGE_V6:ISIS [process-id] failed to send the message that the IPv6 physical interface changed.

Description

IS-IS failed to send the message that reported the change of the IPv6 physical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS failed to send the message that reported the change of the IPv6 physical interface.

Procedure

  1. If a small number of logs are generated, wait for a while to see whether the normal state is entered. If so, no action is required.
  2. If a large number of logs are generated, contact technical support personnel.

ISIS/6/RM_LOGICRC_CHGE

Message

ISIS/6/RM_LOGICRC_CHGE:ISIS [process-id] failed to send the message that the logical interface changed.

Description

IS-IS failed to send the message that reported the change of the logical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS failed to send the message that reported the change of the logical interface.

Procedure

  1. If a small number of logs are generated, wait for a while to see whether the normal state is entered. If so, no action is required.
  2. If a large number of logs are generated, contact technical support personnel.

ISIS/6/RM_LOGICRC_CHGE_V6

Message

ISIS/6/RM_LOGICRC_CHGE_V6:ISIS [process-id] failed to send the message that the IPv6 logical interface changed.

Description

IS-IS failed to send the message that reported the change of the IPv6 logical interface.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS failed to send the message that reported the change of the IPv6 logical interface.

Procedure

  1. If a small number of logs are generated, wait for a while to see whether the normal state is entered. If so, no action is required.
  2. If a large number of logs are generated, contact technical support personnel.

ISIS/6/SB_CIR_NOT_ENABLE

Message

ISIS/6/SB_CIR_NOT_ENABLE:ISIS [process-id] static BFD was not enabled on interface [interface-name].(InterfaceIndex=[STRING])

Description

IS-IS static BFD was not enabled on the interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

InterfaceIndex

Indicates the interface index.

Possible Causes

The static BFD function was not enabled on the interface.

Procedure

  1. Judge whether the static BFD function needs to be enabled on the interface. If so, go to Step 2; if not, go to Step 3.
  2. Run the isis bfd static command.
  3. End.

ISIS/6/SELF_LSP_EXPIRED

Message

ISIS/6/SELF_LSP_EXPIRED:ISIS [process-id] the LSP generated by local system are expired.

Description

The LSP generated by the local system expired.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The life time of the LSP expired

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/ST_LK_CNTRL_FAIL

Message

ISIS/6/ST_LK_CNTRL_FAIL:ISIS [process-id] failed to set link control. (InterfaceIndex=[STRING])

Description

IS-IS failed to set link control.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

InterfaceIndex

Indicates the interface index.

Possible Causes

Failed to set link control.

Procedure

  1. Check the status of the interface.

ISIS/4/START_DISABLE_ISIS

Message

ISIS/4/START_DISABLE_ISIS:ISIS [process-id] disabled all ISIS modules.

Description

IS-IS closed all ISIS modules.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The undo isis command was used to disable IS-IS.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/4/START_ENABLE_ISIS

Message

ISIS/4/START_ENABLE_ISIS:ISIS [process-id] enabled all ISIS modules.

Description

IS-IS started all IS-IS modules.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The isis command was used to enable IS-IS.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_EXPIR_GR_CMD

Message

ISIS/6/T1TMR_EXPIR_GR_CMD:In ISIS [process-id], level-[level] T1 timer expired on [interface-name] during ISIS GR and RR is set.

Description

The Level-2 T1 timer was stopped on an interface during IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.
[level] Indicates the level of IS-IS.
  • 1: level-1

  • 2: level-2

[interface-name] Indicates the name of an interface.

Possible Causes

The Level-2 T1 timer timed out for the second time during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV1_CACEL_GR

Message

ISIS/6/T1TMR_LV1_CACEL_GR:ISIS [process-id] cancelled level-1 T1 timer on [interface-name] during ISIS GR. (Counter=[USHORT])

Description

IS-IS cancelled the Level-1 T1 timer on an interface during IS-IS GR.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

During IS-IS GR, the Level-1 interface received an IIH packet with the RA bit and all series CSNPs.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV1_EXPIR_GR

Message

ISIS/6/T1TMR_LV1_EXPIR_GR:In ISIS [USHORT], level-1 T1 timer expired on [STRING] during ISIS GR.

Description

The Level-1 T1 timer terminated during the IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[USHORT] Indicates the ID of an IS-IS process.
[STRING] Indicates the name of the interface.

Possible Causes

The Level-1 T1 timer terminated during the IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV1_EXPIR_GR_C

Message

ISIS/6/T1TMR_LV1_EXPIR_GR_C:In ISIS [process-id], level-1 T1 timer expired on [interface-name] during ISIS GR. (Counter=[USHORT])

Description

The Level-1 T1 timer was stopped on an interface during IS-IS GR.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

The Level-1 T1 timer timed out for the second time during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/T1TMR_LV1_STOP_CMD

Message

ISIS/5/T1TMR_LV1_STOP_CMD:ISIS [process-id] stopped level-1 T1 timer on [interface-name] because of restart disable.(Counter=[USHORT])

Description

IS-IS stopped the Level-1 T1 timer on an interface because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

When canceling restart, ensure that related the Level-1 T1 timer is stopped.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV2_CACEL_GR

Message

ISIS/6/T1TMR_LV2_CACEL_GR:ISIS [process-id] cancelled level-2 T1 timer on [interface-name] during ISIS GR. (Counter=[USHORT])

Description

IS-IS deleted the Level-2 T1 timer on an interface during IS-IS GR.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

During IS-IS GR, the Level-2 interface received an IIH packet with the RA bit and all series CSNPs.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV2_EXPIR_GR

Message

ISIS/6/T1TMR_LV2_EXPIR_GR:In ISIS [USHORT], level-2 T1 timer expired on [STRING] during ISIS GR.

Description

The Level-2 T1 timer terminated during the IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[USHORT] Indicates the ID of an IS-IS process.
[STRING] Indicates the name of the interface.

Possible Causes

The Level-2 T1 timer terminated during the IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T1TMR_LV2_EXPIR_GR_C

Message

ISIS/6/T1TMR_LV2_EXPIR_GR_C:In ISIS [process-id], level-2 T1 timer expired on [interface-name] during ISIS GR. (Counter=[USHORT])

Description

The Level-1 T1 timer was stopped on an interface during IS-IS GR.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

The Level-1 T1 timer timed out for the second time during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/T1TMR_LV2_STOP_CMD

Message

ISIS/5/T1TMR_LV2_STOP_CMD:ISIS [process-id] stopped level-2 T1 timer on [interface-name] because of restart disable. (Counter=[USHORT])

Description

IS-IS stopped the Level-2 T1 timer on an interface because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

Counter

Indicates a counter.

Possible Causes

When canceling restart, ensure that the related Level-2 T1 timer is stopped.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_LV1_CANCL_GR

Message

ISIS/6/T2TMR_LV1_CANCL_GR:In ISIS [process-id], level-1 T2 timer cancelled during ISIS GR.

Description

The Level-1 T2 timer was cancelled during ISIS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

Level-1 LSDB synchronization was complete during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_LV1_EXPIR_GR

Message

ISIS/6/T2TMR_LV1_EXPIR_GR:In ISIS [process-id], level-1 T2 timer expired during ISIS GR.

Description

The Level-1 T2 timer timed out during ISIS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

The Level-1 T2 timer timed out during ISIS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/T2TMR_LV1_STOP_CMD

Message

ISIS/5/T2TMR_LV1_STOP_CMD:ISIS [process-id] stopped level-1 T2 timer because of restart disable.

Description

IS-IS stopped the Level-1 T2 timer on an interface because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

When canceling restart, ensure that related the Level-1 T2 timer is stopped.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_LV2_CANCL_GR

Message

ISIS/6/T2TMR_LV2_CANCL_GR:In ISIS [process-id], level-2 T2 timer cancelled during ISIS GR.

Description

The Level-2 T2 timer was cancelled during ISIS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

During ISIS GR, Level-2 LSDB synchronization was complete and the Level-2 T2 timer was cancelled.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_LV2_EXPIR_GR

Message

ISIS/6/T2TMR_LV2_EXPIR_GR:In ISIS [process-id], level-2 T2 timer expired during ISIS GR.

Description

The Level-2 TB timer timed out during IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

The Level-2 T2 timer timed out during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/T2TMR_LV2_STOP_CMD

Message

ISIS/5/T2TMR_LV2_STOP_CMD:ISIS [process-id] stopped level-2 T2 timer because of restart disable.

Description

IS-IS stopped the Level-2 T2 timer on an interface because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

When canceling restart, ensure that the related Level-2 T2 timer is stopped.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_STAR_L1_GR

Message

ISIS/6/T2TMR_STAR_L1_GR:T2 timer started on level-1 during ISIS [process-id] GR.

Description

The Level-1 T2 timer was started during IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

During restart or active/standby switch, ISIS entered GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T2TMR_STAR_L2_GR

Message

ISIS/6/T2TMR_STAR_L2_GR:T2 timer started on level-2 during ISIS [process-id] GR.

Description

The Level-2 T2 timer was started during IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

During restart or active/standby switchover, IS-IS entered the GR state.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T3TMR_CANCL_GR

Message

ISIS/6/T3TMR_CANCL_GR:In ISIS [process-id], T3 timer cancelled during ISIS GR.

Description

The T3 timer was cancelled during ISIS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

The T3 timer was cancelled during ISIS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T3TMR_EXPIR_GR

Message

ISIS/6/T3TMR_EXPIR_GR:In ISIS [process-id], T3 timer expired during ISIS GR.

Description

The T3 timer was stopped during ISIS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.

Possible Causes

The T3 timer timed out because IS-IS GR was not complete within a specified period.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T3TMR_REINT_GR

Message

ISIS/6/T3TMR_REINT_GR:In ISIS [process-id], T3 timer re-initialized to [time] seconds on [interface-name] during ISIS GR when received Hello package.

Description

During IS-IS GR, the T3 timer was re-initialized after a Hello packet was received on a link.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of the IS-IS process.
[time] Indicates the time.
[interface-name] Indicates the interface name.

Possible Causes

The IIH packet in which the restart TLV has the RA bit was received during IS-IS GR.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/T3TMR_STAR_GR

Message

ISIS/6/T3TMR_STAR_GR:T3 timer started during ISIS [process-id] GR.

Description

The T3 timer was started during IS-IS GR.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

During restart or active/standby switchover, IS-IS entered the GR state.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/T3TMR_STOP_CMD

Message

ISIS/5/T3TMR_STOP_CMD:ISIS [process-id] stopped T3 timer because of restart disable.

Description

IS-IS stopped the T3 timer on an interface because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

When canceling restart, ensure that the related T3 timer is stopped.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/TMER_STIL_USED

Message

ISIS/6/TMER_STIL_USED:The timer is in use. (TimerType=[ULONG], UsageCount=[ULONG], IsisProcessId=[USHORT])

Description

The timer was in use.

Parameters

Parameter Name Parameter Meaning

TimerType

Indicates the type of a timer.

UsageCount

Indicates the number of timers in use.

IsisProcessId

Indicates the ID of an IS-IS process.

Possible Causes

Internal processing.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/TORM_LEV_GR_DESTR

Message

ISIS/6/TORM_LEV_GR_DESTR:ISIS [USHORT] notifies RM that the process is leaving restart because process was destroyed.

Description

IS-IS notified the RM that the IS-IS process would exit from the restarting because the process itself was destroyed.

Parameters

Parameter Name Parameter Meaning
[USHORT] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS notified the RM that the IS-IS process would exit from the restarting because the process itself was destroyed.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/TORM_LEV_RESTA_SMOH

Message

ISIS/6/TORM_LEV_RESTA_SMOH:ISIS [process-id] notifies RM that the process is leaving restart in consistency smooth.

Description

IS-IS notified RM that the process was to leave the restart state during the consistency smoothing.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

IS-IS GR was not configured during the HA smoothing.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/TORM_LEV_RESTAR_CMD

Message

ISIS/5/TORM_LEV_RESTAR_CMD:ISIS [process-id] notifies RM that the process is leaving restart because of restart disable.

Description

IS-IS notified RM that the process was to leave the restart state because the restart command was deleted.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The restart was canceled.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/TORM_LEV_RESTAR_SPF

Message

ISIS/5/TORM_LEV_RESTAR_SPF:ISIS [process-id] notifies RM that the process is leaving restart after SPF is run.

Description

After the SPF algorithm was used, IS-IS notified RM that the system left the restart state.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

After IS-IS GR and the ISPF calculation were complete, IS-IS notified RM that the system left the GR state.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/5/TORM_RNTR_RESTAR_CMD

Message

ISIS/5/TORM_RNTR_RESTAR_CMD:ISIS [process-id] notifies RM that the process is entering restart because of restart enable.

Description

IS-IS notified RM that the process was to enter the restart state because the restart command was used.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

During restart or active/standby switchover, IS-IS entered the GR state.

Procedure

  1. This log message is informational only, and no action is required.

ISIS/6/UNBIND_SOKT_FAIL

Message

ISIS/6/UNBIND_SOKT_FAIL:ISIS [process-id] failed to unbind socket for the circuit [interface-name]. (InterfaceIndex=[STRING], ReturnValue=[LONG])

Description

IS-IS failed to unbind a socket for an interface.

Parameters

Parameter Name Parameter Meaning

[process-id]

Indicates the ID of an IS-IS process.

[interface-name]

Indicates the name of an interface.

InterfaceIndex

Indicates the interface index.

ReturnValue

Indicates a returned value.

Possible Causes

Failed to unbind a socket for an interface.

Procedure

  1. Check the configuration of the current link.

ISIS/6/WRONG_VERSION

Message

ISIS/6/WRONG_VERSION:ISIS [process-id] dropped the PDU because the PDU version was wrong.

Description

ISIS discarded the PDU packet because the PDU version was wrong.

Parameters

Parameter Name Parameter Meaning
[process-id] Indicates the ID of an IS-IS process.

Possible Causes

The PDU packet was discarded because the PDU version was wrong.

Procedure

  1. This log message is informational only, and no action is required.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065665

Views: 5601

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next