No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
PIM

PIM

PIM/6/ASSERT_CHANGE

Message

PIM/6/ASSERT_CHANGE:In VPN instance "[vpn-instance-name]", ([source-address], [group-address]) interface pim assert fsm was changed from [old-fsm-state] to [new-fsm-state], interface is [interface-name]. (FlCode=[STRING][ULONG])

Description

The PIM Assert state information changed in PIM routing entries.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name]

VPN instance name

[source-address]

Multicast source address

[group-address]

Multicast group address

[old-fsm-state]

Value before the state machine changed

[new-fsm-state]

Value after the state machine changed

[interface-name]

Interface name

FlCode

Name of the source code file and the line number of this log message

Possible Causes

Cause 1:

Duplicate traffic was received on a shared network segment.

Cause 2:

The PIM Assert state timed out.

Procedure

  1. Run the display pim routing-table fsm command to check the Assert state information the (S, G) entry.

    If the (S, G) entry's Assert state is normal, go to Step 3.

    If the (S, G) entry's Assert state is abnormal, go to Step 2.

  2. Run the reset pim [ vpn-instance vpn-instance-name ] routing-table group group-address mask { group-mask-length | group-mask } source source-address interface interface-type interface-number command to delete PIM status information from PIM entries.
  3. End.

PIM/4/ASTPKT_GADD_ERR1

Message

PIM/4/ASTPKT_GADD_ERR1:In VPN instance "[vpn-instance-name]", the received Assert packet with an incorrect group address was ignored. (FlCode=[STRING][ULONG])

Description

The Assert packet was discarded because the group address was invalid.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The Assert packet was discarded because the group address was invalid.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, record this log message, and then contact technical support personnel.

PIM/4/BACKUPJP_NORP

Message

PIM/4/BACKUPJP_NORP:In VPN instance "[vpn-instance-name]", when trying to send a (*, [group-address]) Join message, PIM cannot obtain the RP. (FlCode=[STRING][ULONG])

Description

The PIM failed to obtain the RP when trying to send a Join message (*,G).

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The RP is not backed up to the slave board, causing the PIM unable to find the RP after the GR process.

Procedure

  1. Run the display pim [ vpn-instance vpn-instance-name | all-instance ] rp-info command to check whether the RP exists.
  2. Run the static-rp or c-rp command in the PIM view to configure the RP.

PIM/4/BSR_GRP_SCOPE_ERR

Message

PIM/4/BSR_GRP_SCOPE_ERR:In VPN instance "[vpn-instance-name]", the BSR packet received from [bsr-address] and with wrong group [group-address]'s scope was ignored. (FlCode=[STRING][ULONG])

Description

In the multicast NSR scenario, the slave MPU received incorrect BSR messages when the master MPU backs up information to the slave MPU.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[bsr-address] Indicates the address of the BSR.
[group-address] Indicates the address of a group.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

In the multicast NSR scenario, the slave MPU received incorrect BSR messages when the master MPU backs up information to the slave MPU.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/4/BSR_GRPLOC

Message

PIM/4/BSR_GRPLOC:In VPN instance "[vpn-instance-name]", the BSR packet whose group address [group-address]/[mask] was the local multicast address was ignored. (FlCode=[STRING][ULONG])

Description

The BSR packet whose group address was the local multicast address was ignored.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the address of a group.
[mask] Indicates the mask of the group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

A BSR packet with an invalid group address was received.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, record this log message, and then contact technical support personnel.

PIM/4/CHANGE_TO_NON_DR

Message

PIM/4/CHANGE_TO_NON_DR:In VPN instance "[vpn-instance-name]", interface [interface-name] ([interface-address]) is changed to Non-DR. New DR is [dr-address]. (FlCode=[STRING][ULONG])

Description

A PIM interface changed from a DR to a non-DR.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name]

VPN instance name

[interface-name]

Interface name

[interface-address]

Interface address

[dr-address]

DR address

FlCode

Name of the source code file and the line number of this log message

Possible Causes

An interface functioning as a PIM DR received a PIM Hello message having a higher DR priority or received a PIM Hello message from an interface having a greater IP address. Then, the current interface changed to a non-DR interface.

Procedure

  1. Check whether the interface needs to function as the DR interface.

    If so, go to Step 2.

    If not, go to Step 3.

  2. Run the pim hello-option dr-priority priority command to a higher DR priority for the interface, or run the ip address ip-address command to set a greater IP address for the interface.
  3. End.

PIM/4/CRPADV_FAMERR

Message

PIM/4/CRPADV_FAMERR:In VPN instance "[vpn-instance-name]", the group address family [group-address-family] was invalid, ignored this group [group-address]. (FlCode=[STRING][ULONG])

Description

The CRP_ADV packet with invalid group address family was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address-family] Indicates the address family of a group.
[group-address] Indicates the address of a group.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

An invalid CRP_ADV packet was received.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/4/CRPADV_GRPERR

Message

PIM/4/CRPADV_GRPERR:In VPN instance "[vpn-instance-name]", the packet with an incorrect group address was ignored. (FlCode=[STRING][ULONG])

Description

The packet with an incorrect group address was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

An invalid CRP_ADV packet was received.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, record this log message, and then contact technical support personnel.

PIM/4/CRPADV_GRPINV

Message

PIM/4/CRPADV_GRPINV:In VPN instance "[vpn-instance-name]", the group whose group address [group-address]/[mask] was not the multicast address was ignored. (FlCode=[STRING][ULONG])

Description

A packet with a non-multicast group address was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the address of a group.
[mask] Indicates the mask of the group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

An invalid CRP_ADV packet was received.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, record this log message, and then contact technical support personnel.

PIM/4/CRT_SG_FAIL

Message

PIM/4/CRT_SG_FAIL:In VPN instance [vpn-instance-name], PIM-SSM failed to create the ([source-address], [group-address]) entry in the multicast routing table. (FlCode=[STRING][ULONG])

Description

Failed to create the (S, G) entry.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[source-address] Indicates a multicast source address.
[group-address] Indicates a multicast group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

1. The multicast source was filtered out.

2. The memory was not enough.

3. The current route entries reached the upper limit.

Procedure

  1. Run the display acl { acl-number | all } command to ensure the (S, G) will not be filtered out, that is, ensure that the source address and group address will not be denied by the ACL applied to multicast.
  2. Ensure that system memory is enough.
  3. Run the display pim routing-table, display multicast routing-table, and display multicast forwarding-table commands to check the total number of PIM entries, multicast route entries and forwarding entries. Ensure that the total number does not reach the upper limit specified in the current PIM version.
  4. Collect log information and configuration information, and then contact technical support personnel.

PIM/6/DISCA_PRIADDR

Message

PIM/6/DISCA_PRIADDR:In VPN instance [vpn-instance-name], because the address was the same as the link-local address of the PIM IPv6 neighbor or the primary address of the PIM IPv4 neighbor, the hello message received from the interface [interface] was ignored. (FlCode=[STRING][ULONG])

Description

A Hello message with an incorrect primary address was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[interface] Indicates an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The secondary address of a received Hello message was ignored because this address was the same as the link-local address of the PIM IPv6 neighbor or the primary address of the PIM IPv4 neighbor.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/4/FNDNBR_DNDB_F

Message

PIM/4/FNDNBR_DNDB_F:In VPN instance "[vpn-instance-name]", finding neighbor [neighbor-address] on interface [interface-name] ([interface-address]) from entry ([source-address]/[source-address-mask], [group-address]/[group-address-mask])'s DNDB failed. (FlCode=[STRING][ULONG])

Description

Failed to find the corresponding neighbor record in the DNDB.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[neighbor-address] Indicates the IP address of a neighbor.
[interface-name] Indicates the name of an interface.
[interface-address] Indicates the IP address of an interface.
[source-address] Indicates the source address.
[source-address-mask] Indicates the mask of the source address.
[group-address] Indicates the address of a group.
[group-address-mask] Indicates the mask of the group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

Failed to find the corresponding neighbor record in the DNDB.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

PIM/5/GR_END

Message

PIM/5/GR_END:In VPN instance "[vpn-instance-name]", PIM left the GR status. The reason code was [reason-code]. (FlCode=[STRING][ULONG])

Description

The VPN instance exited from the PIM GR state.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[reason-code]
Indicates the reason code. The value can be:
  • 0: The parameter is invalid.

  • 1: The GR timer expires and the GR process is ended normally.

  • 2: Multicast is disabled to end GR.

  • 3: PIM SM is disabled to end GR.

  • 4: GR of the VPN instance is ended.

  • 5: The Force timer expires and the GR process is ended.

  • 6: GR is not enabled and is directly ended.

  • 7: Other components are terminated and thus GR is ended.

FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

  1. The GR timer expires.

  2. The VPN instance that perform PIM GR is deleted.

  3. The interface board where the last PIM-SM interface resides is removed.

  4. The GR timer of the IPv4 public network expires. When the GR processes of the VPN instances that depend on the IPv4 public network are ended, the GR process of the IPv4 public network is ended.

Procedure

  • This log message is informational only, and no action is required.

PIM/5/GR_START

Message

PIM/5/GR_START:In VPN instance "[vpn-instance-name]", PIM entered the GR status. The minimum holding time was [gr-period] seconds. (FlCode=[STRING][ULONG])

Description

The VPN instance entered the PIM GR state.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[gr-period] Indicates the GR period.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

PIM GR is enabled in the VPN instance, and the master/slave switchover is performed.

Procedure

  • This log message is informational only, and no action is required.

PIM/6/GRP_ADDR_IS_LOCAL

Message

PIM/6/GRP_ADDR_IS_LOCAL:In VPN instance [vpn-instance-name], because the group address [group-address]/[group-mask-length] is a link/node local address, the [message-type] message received from the interface [interface-name] was ignored. (FlCode=[STRING][ULONG])

Description

The group address contained in a PIM message, which was a local multicast address, was ignored.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the group address.
[group-mask-length] Indicates the mask length of group address.
[message-type] Indicates the message type. The value can be:
  • PIM Join/Prune message

  • PIM SM Assert message

  • PIM SM Register-Stop message

  • PIM SSM Assert message

[interface-name] Indicates the name of an interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The PIM-SM-enabled interface receives a PIM message, the group address contained in which is a local multicast address.

Procedure

  • This log message is informational only, and no action is required.

PIM/6/GRP_ADDR_NOT_MCAST

Message

PIM/6/GRP_ADDR_NOT_MCAST:In VPN instance [vpn-instance-name], because the group address [group-address]/[group-mask-length] is not a multicast address, the [message-type] message received from the interface [interface-name] was ignored. (FlCode=[STRING][ULONG])

Description

The group address contained in a PIM message, which was not a multicast address, was ignored.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the group address.
[group-mask-length] Indicates the mask length of group address.
[message-type] Indicates the message type. The value can be:
  • PIM Join/Prune message

  • PIM SM Assert message

  • PIM SM Register-Stop message

  • PIM SSM Assert message

[interface-name] Indicates the name of an interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The PIM-SM-enabled interface receives a PIM message, the group address contained in which is not a multicast address.

Procedure

  • This log message is informational only, and no action is required.

PIM/6/GRP_MASK_UNSUPPORTED

Message

PIM/6/GRP_MASK_UNSUPPORTED:In VPN instance [vpn-instance-name], because the length of the mask of the group address [group-address]/[group-mask-length] is unsupported, the [message-type] message received from the interface [interface-name] was ignored. (FlCode=[STRING][ULONG])

Description

The group address contained in a PIM message was ignored, because the mask length of the group address was not supported by PIM.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[group-address] Indicates the group address.
[group-mask-length] Indicates the mask length of group address.
[message-type] Indicates the message type. The value can be:
  • PIM Join/Prune message

  • PIM SM Assert message

  • PIM SM Register-Stop message

  • PIM SSM Assert message

[interface-name] Indicates the name of an interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The PIM-SM-enabled interface receives a PIM message, the mask length of the group address contained in which is not supported by PIM.

Procedure

  • This log message is informational only, and no action is required.

PIM/6/HELPKT_UNSADDR_ERR

Message

PIM/6/HELPKT_UNSADDR_ERR:In VPN instance [vpn-instance-name] because the unicast source address was incorrect, the Hello packet received from the interface [interface] was ignored. (FlCode=[STRING][ULONG])

Description

A Hello message with an incorrect unicast source address was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[interface] Indicates an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

A Hello message with an incorrect unicast source address was discarded.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/3/HOLDTIME_LESS_INL

Message

PIM/3/HOLDTIME_LESS_INL:In VPN instance "[vpn-instance-name]", when the BSR holdtime and sending interval were configured, the BSR holdtime [holdtime] was less than the sending interval [interval]. (FlCode=[STRING][ULONG])

Description

The BSR holdtime is smaller than the BSR sending interval.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[holdtime] Indicates the BSR holdtime.
[interval] Indicates the interval for sending BSR messages.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

This log message is generated when BSR parameters are configured or modified.

Procedure

  1. Run the c-bsr holdtime interval command to reconfigure the BSR holdtime. Run the c-bsr interval interval command to reconfigure the interval for the BSR to send Bootstrap messages. Ensure that the BSR holdtime is greater than the BSR sending interval.

PIM/4/INT_INV

Message

PIM/4/INT_INV:In VPN instance [vpn-instance-name], a PIM packet received on an unknown interface was discarded, the interface index was [index]. (FlCode=[STRING][ULONG])

Description

The PIM packet was received on an unknown interface and was then discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[index] Indicates the index of an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

An unexpected interface event occurred.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/5/INVSRC

Message

PIM/5/INVSRC:In VPN instance [vpn-instance-name], the invalid source address [source-address] was ignored, the packet received from the interface [interface]. (FlCode=[STRING][ULONG])

Description

The source address of the received protocol packet was invalid.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[source-address] Indicates the source address.
[interface] Indicates an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The source address of the (S, G) entry to be created is unreachable.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

PIM/4/JP_SRCERR

Message

PIM/4/JP_SRCERR:In VPN instance "[vpn-instance-name]", the Join/Prune packet with an incorrect source address was ignored when being processed. (FlCode=[STRING][ULONG])

Description

The Join/Prune message with an incorrect source address was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The Join/Prune message with an incorrect source address was discarded.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/6/MTU_IF_SHT

Message

PIM/6/MTU_IF_SHT:In VPN instance "[vpn-instance-name]", the MTU of the interface [interface-name] was [mtu], which was too small to send pim Hello packet. (FlCode=[STRING][ULONG])

Description

Failed to send the PIM Hello message because the MTU of the interface was too small.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[interface-name] Indicates the name of an interface.
[mtu] Indicates the Maximum Transmission Unit (MTU).
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

Failed to send the PIM Hello message because the MTU of the interface was too small.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/4/NBR_DOWN

Message

PIM/4/NBR_DOWN:In VPN instance "[vpn-instance-name]", a neighbor was deleted from the interface. The reason is [reason] (NeighborIpAddress=[STRING], Interface=[STRING], FlCode=[STRING][ULONG])

Description

A neighbor was deleted from the neighbor list of the interface.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[reason]
Indicates the possible causes of PIM neighbor loss:
  • Hold time expired

  • Receive hello message with holdTime zero

  • BFD session down

  • PIM status of the interface changes

NeighborIpAddress Indicates the IP address of a neighbor.
Interface Indicates the name of an interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

1. The interface did not receive any Hello message within a certain period, which caused the timeout of the PIM neighbor relationship.

2. The interface received a Hello message with the Holdtime field being 0.

3. The BFD session on the interface was Down.

4. PIM status of the interface changes.

Procedure

  1. Run the display pim [ vpn-instance vpn-instance-name | all-instance ] interface verbose command to check whether the interface is in the Up state and check the BFD session status. Ensure that the link can work normally.
  2. Collect log information and configuration information, and then contact technical support personnel.

PIM/4/NBR_DOWN_ALL

Message

PIM/4/NBR_DOWN_ALL:In VPN instance "[vpn-instance-name]", all neighbors were deleted from the interface because the interface was down or PIM was disabled on the interface. (Interface=[STRING], FlCode=[STRING][ULONG])

Description

All PIM neighbors were deleted from the interface because the interface became Down or PIM was disabled on the interface.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name]

Indicates the name of the VPN instance.

Interface

Indicates the interface name.

FlCode

Indicates the name of the source code file and the line number of this log message.

Possible Causes

1. The interface became Down.

2. PIM was disabled.

Procedure

  1. Run the display pim [ vpn-instance vpn-instance-name | all-instance ] interface verbose command to check whether the interface is in the Up state. Ensure that the link works normally.
  2. Collect log information and configuration information, and then contact technical support personnel.

PIM/4/NBR_UP

Message

PIM/4/NBR_UP:In VPN instance "[vpn-instance-name]", a new neighbor was created on the interface. (NeighborIpAddress=[STRING], Interface=[STRING], FlCode=[STRING][ULONG])

Description

A neighbor was added to the neighbor list of the interface.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
NeighborIpAddress Indicates the IP address of a neighbor.
Interface Indicates the name of an interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

A PIM Hello message was received from a new neighbor.

Procedure

  • This log message is informational only, and no action is required.

PIM/4/PIMPKT_CHKSUM_ERR

Message

PIM/4/PIMPKT_CHKSUM_ERR:In VPN instance [vpn-instance-name], the PIM packet received from [source-address] was discarded because the checksum of this packet was incorrect, the message type was [message-type] received from the interface [interface] .(FlCode=[STRING][ULONG])

Description

The received PIM packet was discarded because the checksum was incorrect.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[source-address] Indicates a source address.
[message-type] Indicates a message type.
[interface] Indicates an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

1. Bad conditions of the link lead to the transmission error.

2. The received packet is an attack PIM packet.

Procedure

  1. If the fault occurs occasionally, the fault may be caused by link transmission, and this log message can be ignored.
  2. If the fault occurs frequently, check the link conditions and use the packet header obtaining tool to obtain PIM packets. Obtain information about manufacturers and versions of other devices in the shared network and network topology, and then contact technical support personnel.

PIM/4/PIM_GR_FORCE_SYNC

Message

PIM/4/PIM_GR_FORCE_SYNC:In VPN instance "[vpn-instance-name]", PIM was forced to enter the GR Synchronous state. (FlCode=[STRING][ULONG])

Description

PIM was forced to enter the GR Synchronous state.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Name of a VPN instance
FlCode Name of the source code file and the line number of this log message

Possible Causes

Unicast GR was not complete, but the PIM GR force timer expired.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

PIM/4/PIMAST_LOSSER_JOIN

Message

PIM/4/PIMAST_LOSSER_JOIN:In VPN instance "[vpn-instance-name]", a PIM JOIN from [source-address] on [interface-name] for ([multicast-source-address], [multicast-group-address]) was received when assert state is losser. (FlCode=[file-code][line-number])

Description

A PIM interface in the assert loser state received a Join message.

Parameters

Parameter Name Parameter Meaning

[vpn-instance-name]

VPN instance name

[source-address]

Source IP address of the Join message

[interface-name]

Interface name

[multicast-source-address]

Multicast source address

[multicast-group-address]

Multicast group address

FlCode

Name of the source code file and the line number of this log message

Possible Causes

A PIM interface in the assert loser state received a Join message.

Procedure

  1. This log message is informational only, and no action is required.

PIM/3/PUTNBR_DNDB_F

Message

PIM/3/PUTNBR_DNDB_F:In VPN instance "[vpn-instance-name]", adding neighbor [neighbor-address] on interface [interface-name] ([group-address]) to entry ([source-address]/[source-address-mask], [group-address]/[group-address-mask])'s DNDB failed. (FlCode=[STRING][ULONG])

Description

Failed to add information about a neighbor into the DNDB.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[neighbor-address] Indicates the IP address of a neighbor.
[interface-name] Indicates the name of an interface.
[group-address] Indicates the address of a group.
[source-address] Indicates the source address.
[source-address-mask] Indicates the mask of the source address.
[group-address-mask] Indicates the mask of the group address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

Failed to add information about a neighbor into the DNDB.

Procedure

  1. Check that the number of neighbors does not exceed 128.
  2. Collect log information and configuration information, and then contact technical support personnel.

PIM/6/SEC_ADDRFA_ERR

Message

PIM/6/SEC_ADDRFA_ERR:In VPN instance [vpn-instance-name], the packet with an unknown secondary address family [address-family] was ignored, and the packet received from the interface [interface]. (FlCode=[STRING][ULONG])

Description

A Hello message with an unknown secondary address family was discarded.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[address-family] Indicates the address family.
[interface] Indicates an inbound interface.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

A Hello message with an unknown secondary address family was discarded.

Procedure

  1. If this fault occurs occasionally, this log message can be ignored.
  2. If the fault frequently occurs, check the packet source, record this log message, and then contact technical support personnel.

PIM/3/SOCK_ERR1

Message

PIM/3/SOCK_ERR1:In VPN instance [vpn-instance-name], PIM failed to set socket option that multicast joined the PIM group. The error code was [error-code], the interface was [interface]. (FlCode=[STRING][ULONG])

Description

Failed to join the PIM group by setting the Socket option.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[error-code] Indicates an error code.
[interface] Specifies an interface name.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

Failed to join the PIM router group by setting the Socket option.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

PIM/6/SRC_MASK_UNSUPPORTED

Message

PIM/6/SRC_MASK_UNSUPPORTED:In VPN instance [vpn-instance-name], the length of the mask of the source address [source-address]/[source-mask-length] in the Join/Prune message was unsupported, so this source was ignored. (FlCode=[STRING][ULONG])

Description

The source address contained in the Join/Prune message was ignored, because PIM-SM did not support the mask length of the source address.

Parameters

Parameter Name Parameter Meaning
[vpn-instance-name] Indicates the name of a VPN instance.
[source-address] Indicates the source address.
[source-mask-length] Indicates the mask length of source address.
FlCode Indicates the name of the source code file and the line number of this log message.

Possible Causes

The PIM-SM-enabled interface receives a Join/Prune message, the mask length of the source address contained in which is not supported by PIM-SM.

Procedure

  • This log message is informational only, and no action is required.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065665

Views: 5482

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next