No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
SOCKET

SOCKET

SOCKET/4/ASYNACCEPTFAIL

Message

SOCKET/4/ASYNACCEPTFAIL:Failed to allocate the file describer for the sub socket when accept was called to accept incoming connection request. (Time=[ULONG], TaskName=[STRING], TaskId=[ULONG], SocketId=[ULONG], ErrorCode=[LONG])

Description

Failed to allocate the file descriptor to the socket when the Accept function was called to receive the connection request.

Parameters

Parameter Name Parameter Meaning
Time indicates the time when the log is generated.
TaskName indicates the task name.
TaskId indicates the task ID.
SocketId indicates the socket ID.
ErrorCode indicates the error codes, that is, -101, -24, and -55.

Possible Causes

1. Because the system memory was insufficient, namely, the memory was used up or nearly used up, the TCP listening socket could not receive the connection request from the client, and the connection failed.

2. The number of socket connections of the current task exceeds the upper limit (23 x 1024). Therefore, the file descriptor cannot be allocated to the socket, and the connection fails to be set up.

Procedure

  1. If the fault is caused by the insufficient memory, cancel some memory-consuming and unnecessary applications.
  2. If the fault is caused by the insufficient file descriptors, cancel some applications that occupy a large number of file descriptors. In this manner, you can release enough file descriptors for current applications.

SOCKET/1/BINDPEERIP

Message

SOCKET/1/BINDPEERIP:Failed to bind the peer IP because a socket with same state already existed.

Description

Failed to bind the peer IP address because a socket in the system had the same status as that of the current socket.

Parameters

Parameter Name Parameter Meaning
None None

Possible Causes

1. The peer IP address was repeatedly set.

2. The system had a socket with the same local IP address, local port number, remote IP address, remote port number, and VPN index as that of the socket to be set.

Procedure

  1. The log is generated when the system faces an unknown fault. The fault causes the relevant routing protocol unavailable. Then you need disable the routing protocol and then enable it.

SOCKET/4/CANTGETLSTNSOCK

Message

SOCKET/4/CANTGETLSTNSOCK:Failed to obtain the ID of the listening socket. (TaskId=[ULONG], SocketId=[ULONG], ErrorCode=[LONG])

Description

Failed to acquire the listening socket ID.

Parameters

Parameter Name Parameter Meaning
TaskId indicates the task ID.
SocketId indicates the socket ID.
ErrorCode indicates the error codes, that is, -22 and -107.

Possible Causes

A software error occurred in the system. Then the relevant task control block could not be found according to the task ID, or the relevant socket could not be found according to the file descriptor. You can consider that the fault has nearly no chance to occur.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

SOCKET/4/EXCEEDMAXQLEN

Message

SOCKET/4/EXCEEDMAXQLEN:The number of messages in the asynchronous message queue was greater than the message upper limit. (Time=[ULONG], TaskName=[STRING], TaskId=[ULONG], SocketId=[ULONG], ErrorCode=[LONG])

Description

The number of messages in the asynchronous message queue exceeded the defined upper limit.

Parameters

Parameter Name Parameter Meaning
Time indicates the time when the log is generated.
TaskName indicates the task name.
TaskId indicates the task ID.
SocketId indicates the socket ID.
ErrorCode indicates the error code, that is, -8.

Possible Causes

Each asynchronous socket has a queue to receive messages. This log indicates that the message queue was full and no new message could be received. The cause is that the speed in which the CPU read messages was slower than the speed to generate messages. In most cases, the fault is caused when a large number of packets are generated in the network, and the CPU is too busy to handle received messages in time. Therefore, the message queue becomes full and the received subsequent data is discarded.

Procedure

  1. Reduce the workload of the CPU by canceling some processes that are CPU-time consuming and unnecessary.
  2. If possible, wait till the CPU is idle and then configure relevant tasks.
  3. Collect log information and configuration information, and then contact technical support personnel.

SOCKET/6/FGETVPNNAME

Message

SOCKET/6/FGETVPNNAME:The current socket failed to obtain the VPN name. (ErrorCode=[ULONG])

Description

The current socket failed to acquire the VPN name.

Parameters

Parameter Name Parameter Meaning
ErrorCode Indicates an error code. The error codes are shown as follows

4: indicates that the input parameter is invalid.

5: indicates that the VRF name is inexistent.

7: indicates that the VRF is in the inactive state.

Possible Causes

A socket was closed, and then the VPN information about the closed socket was recorded into the log. During the process to acquire the VPN information, a fault occurred, and the relevant VPN information could not be acquired.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/LSTNASYNQUEINFO

Message

SOCKET/6/LSTNASYNQUEINFO:The verbose information about the current asynchronous queue in listening state was displayed. (Read=[ULONG], Write=[ULONG], Connect=[ULONG], Close=[ULONG], PeerClose=[ULONG], Accept=[ULONG], KeepAliveDown=[ULONG], Crammed at: [ULONG]:[ULONG]:[ULONG](Hour:Minute:Seconds), LostMessage=[ULONG], MessageType=[ULONG])

Description

The detailed information about the asynchronous message queue in the listening status was described in the log.

Parameters

Parameter Name Parameter Meaning
Read indicates the number of Read messages.
Write indicates the number of Write messages.
Connect indicates the number of Connect messages.
Close indicates the number of Close messages.
PeerClose indicates the number of PeerClose messages.
Accept indicates the number of Accept messages.
KeepAliveDown indicates the number of Keep Alive Down messages.
Crammed at indicates the time when the asynchronous message queue becomes full. The format is HH:MM:SS.
LostMessage indicates the number of lost messages.
MessageType indicates the type of lost messages. The types of lost messages are shown as follows

1. Read

2. Write

3. Connect

4. Close

5. Accept

6. PeerClose

7. KeepAliveDown

Possible Causes

The TCP listening socket was closed for a certain cause, and then the information about the asynchronous message queue at the closed TCP listening socket was recorded.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/SGETVPNNAME

Message

SOCKET/6/SGETVPNNAME:The current socket succeeded to obtain the VPN name. (VPNName=[STRING])

Description

The current socket successfully acquired a VPN name.

Parameters

Parameter Name Parameter Meaning
VPNName indicates the name of a VPN instance.

Possible Causes

A socket was closed, and then the VPN information about the closed socket was recorded into the log.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/4/SO_ACCEPTCFAIL

Message

SOCKET/4/SO_ACCEPTCFAIL:The error code of SO_Accept was returned. (Time=[ULONG], TaskName=[STRING], TaskId=[ULONG], SocketId=[ULONG], ErrorCode=[LONG])

Description

The Accept function failed and an error code was returned.

Parameters

Parameter Name Parameter Meaning
Time indicates the time when the log is generated.
TaskName indicates the task name.
TaskId indicates the task ID.
SocketId indicates the socket ID.
ErrorCode indicates the error code -55.

Possible Causes

Because the system memory was insufficient, namely, the memory was used up or nearly used up, the TCP listening socket could not receive the connection request from the client, and the connection failed.

Procedure

  1. Collect log information and configuration information, and then contact technical support personnel.

SOCKET/6/SOCKCLOSED

Message

SOCKET/6/SOCKCLOSED:The current socket was closed. (ProtocolName=[STRING], Cause=[STRING])

Description

The current socket was turned off.

Parameters

Parameter Name Parameter Meaning
ProtocolName indicates the protocol name. The protocol names are shown as follows

1. RAWLINK

2. RAWIP

3. TCP

4. UDP

Cause indicates the triggering condition. The triggering conditions are shown as follows

1. Application closed socket

2. Received reset fragment

3. Retransfer timeout

4. Keepalive timeout

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/SOCKNOTEXIST

Message

SOCKET/6/SOCKNOTEXIST:The current socket did not exist. (TaskName=[STRING], Socket=[STRING], ProtocolName=[STRING])

Description

The current socket was inexistent.

Parameters

Parameter Name Parameter Meaning
TaskName indicates the task name.
Socket indicates the socket ID.
ProtocolName indicates the protocol name.

Possible Causes

Failed to find the socket control block in the system.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/SUBQUEINFO

Message

SOCKET/6/SUBQUEINFO:The verbose information about the current subqueue was displayed. (Full at: [ULONG]:[ULONG]:[ULONG](Hour:Minute:Seconds), Ready at: [ULONG]:[ULONG]:[ULONG](Hour:Minute:Seconds), CurrentState=[STRING], Number of refused connections=[ULONG])

Description

The detailed information about the current connected sub-queues was described in the log.

Parameters

Parameter Name Parameter Meaning
Full at indicates the time when the sub-queue at the TCP listening socket is full. The format is HH:MM:SS.
Ready at indicates the time when the sub-queue at the TCP listening socket is ready to accept packets after being full. The format is HH:MM:SS.
CurrentState indicates a current state. The current states are shown as follows

(1) full

(2) ready

Number of refused connections indicates the number of connections refused by the server.

Possible Causes

The TCP listening socket was closed for a certain cause, and then the information about the closed TCP listening socket was recorded.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/4/TCP_AUTH_FAILED

Message

SOCKET/4/TCP_AUTH_FAILED:TCP authentication failed. (AuthenticationType=[STRING], Cause=[STRING], SourceAddress=[IPADDR], SourcePort=[USHORT], ForeignAddress=[IPADDR], ForeignPort=[USHORT], Protocol=[STRING], VpnInstanceName=[STRING])

Description

An upper-layer application protocol configured the MD5 or keychain authentication password for the TCP connection, but the MD5 or keychain authentication failed when the TCP connection was established.

Parameters

Parameter Name Parameter Meaning
AuthenticationType

Authentication type. It can be MD5 or keychain.

Cause Cause of the authentication failure.
SourceAddress Source IP address.
SourcePort Source port number.
ForeignAddress Destination IP address.
ForeignPort Destination port number.
Protocol

Upper-layer application protocol, such as BFD and LDP.

VpnInstanceName VPN instance name.

Possible Causes

Cause 1:

Different authentication modes were configured on the local and remote devices. Do not configure MD5 authentication on one end and configure keychain mode on the other end.

Cause 2:

Different MD5 authentication passwords were configured on the local and remote devices.

Cause 3:

Different keychain encryption algorithms and authentication passwords were configured on the local and remote devices.

Procedure

  1. Based on the configuration requirements and procedures of MD5 or keychain mode, check whether the configuration is correct.

SOCKET/6/TCPASYNQUEINFO

Message

SOCKET/6/TCPASYNQUEINFO:The verbose information about the asynchronous queue of the current TCP socket was displayed. (Read=[ULONG], Write=[ULONG], Connect=[ULONG], Close=[ULONG], PeerClose=[ULONG], Accept=[ULONG], KeepAliveDown=[ULONG], Full at: [ULONG]:[ULONG]:[ULONG] (Hour:Minute:Second), LostMessage=[ULONG], MessageType=[ULONG])

Description

The detailed information about the asynchronous message queue of the current TCP socket was described in the log.

Parameters

Parameter Name Parameter Meaning
Read indicates the number of Read messages.
Write indicates the number of Write messages.
Connect indicates the number of Connect messages.
Close indicates the number of Close messages.
PeerClose indicates the number of PeerClose messages.
Accept indicates the number of Accept messages.
KeepAliveDown indicates the number of Keep Alive Down messages.
Full at indicates the time when the asynchronous message queue becomes full. The format is HH:MM:SS.
LostMessage indicates the number of lost messages.
MessageType indicates the type of lost messages. The types of lost messages are shown as follows

1. Read

2. Write

3. Connect

4. Close

5. Accept

6. PeerClose

7. KeepAliveDown

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/TCPCONNBLK

Message

SOCKET/6/TCPCONNBLK:The current TCP connection was blocked at [ULONG]:[ULONG]:[ULONG] (Hour:Minute:Second)

Description

The current TCP connection was blocked.

Parameters

Parameter Name Parameter Meaning
blocked at indicates the time when the TCP connection or disconnection is cut off. The format is HH:MM:SS.

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/TCPIOSTAT

Message

SOCKET/6/TCPIOSTAT:The statistic of the packets sent and received through the current TCP connection was displayed. (Input=[ULONG], ReceivedPackets=[ULONG], SentPackets=[ULONG])

Description

The statistics of the input and output traffic in the current TCP connection were described in the log.

Parameters

Parameter Name Parameter Meaning
Input indicates the total number of TCP packets received by the socket. Note that TCP packets include TCP control packets and TCP data packets.
ReceivedPackets indicates the total number of TCP data packets received by the socket.
SentPackets indicates the total number of TCP packets output by the socket.

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  1. This log message indicates a normal situation, and no action is required.

SOCKET/6/TCPWNDCLOSE

Message

SOCKET/6/TCPWNDCLOSE:The peer closed the TCP receival window, namely, the size of the peer's receival window was zero and the local end could not send data. (Started at [ULONG]:[ULONG]:[ULONG] (Hour:Minute:Second), Total times of closing the window=[ULONG])

Description

The remote end in a TCP connection closed the sliding window, which means that the value of the sliding window was zero and the local end could not send data any more.

Parameters

Parameter Name Parameter Meaning
Started at indicates the time when remote end in a TCP connection lastly notifies that the value of its sliding window is 0. The format is HH:MM:SS.
Total times of closing the window indicates the times that the sliding window of the remote end in a TCP connection is not available.

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  • This log message indicates a normal situation, and no action is required.

SOCKET/6/VRBSRIPSOCKINFO

Message

SOCKET/6/VRBSRIPSOCKINFO:The verbose information about the current RawIP socket was displayed. (SocketPair: [STRING], ProtocolNumber=[ULONG])

Description

The detailed information about the current RAWIP socket was described in the log.

Parameters

Parameter Name Parameter Meaning
SocketPair indicates the information about the RAWIP address.
ProtocolNumber indicates the protocol number of RAWIP.

Possible Causes

A RAWIP socket was closed, and then the current status, local IP address, and remote IP address of the closed RAWIP socket were recorded into the log.

Procedure

  • This log message indicates a normal situation, and no action is required.

SOCKET/6/VRBSSOCKINFO

Message

SOCKET/6/VRBSSOCKINFO:The verbose information about the current socket was displayed. (Task=[STRING]([ULONG]), Socket=[ULONG]([STRING]), ProtocolNumber=[ULONG])

Description

The detailed information about the current socket was described in the log.

Parameters

Parameter Name Parameter Meaning
Task indicates a task, including the task name and task ID.
Socket indicates the ID and the protocol type of a socket. The protocol types are shown as follows
  • RAWLINK

  • RAWIP

  • TCP

  • UDP

ProtocolNumber indicates the number of the transport layer protocol. The value ranges from 1 to 255.

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  • This log message indicates a normal situation, and no action is required.

SOCKET/6/VRBSTCPSOCKINFO

Message

SOCKET/6/VRBSTCPSOCKINFO:The verbose information about the current TCP socket was displayed. (State=[STRING], SocketPair: [STRING])

Description

The detailed information about the current TCP socket was described in the log.

Parameters

Parameter Name Parameter Meaning
State indicates the TCP state. The TCP states are shown as follows

1. Closed

2. Listening

3. Syn_Sent

4. Syn_Rcvd

5. Established

6. Close_Wait

7. Fin_Wait1

8. Closing

9. Last_Ack

10.Fin_Wait2

11.Time_Wait

SocketPair indicates the socket pair, that is, TCP quadbit.

Possible Causes

1. The user called the Close function to turn off the socket.

2. The TCP server received RST packets from the TCP client.

3. TCP retransmission timed out.

4. Failed to perform TCP keepalive detection.

Procedure

  • This log message indicates a normal situation, and no action is required.

SOCKET/6/VRBSUDPSOCKINFO

Message

SOCKET/6/VRBSUDPSOCKINFO:The verbose information about the current UDP socket was displayed. (SocketPair: [STRING])

Description

The detailed information about the current UDP socket was described in the log.

Parameters

Parameter Name Parameter Meaning
SocketPair indicates the socket pair, that is, UDP quadbit.

Possible Causes

A UDP socket was closed, and then the current status, local IP address, local port number, remote IP address, and remote port number of the closed UDP socket were recorded in the log.

Procedure

  1. This log message indicates a normal situation, and no action is required.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065665

Views: 5467

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next