No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R013C00 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
QOSE

QOSE

QOSE/3/CAR_FAIL

Message

QOSE/3/CAR_FAIL:Failed to execute ([STRING1]) on interface [STRING2] due to insufficient resources in slot [STRING3].

Description

The qos car inbound command fails to be executed due to insufficient ACL resources on the LPU.

Parameters

Parameter Name Parameter Meaning
STRING1 Command that fails to be executed, that is, qos car inbound.
STRING2 Eth-Trunk ID.
STRING3 Slot ID of an LPU.

Possible Causes

The qos car inbound command is configured on an Eth-Trunk. When a new member interface joins the Eth-Trunk, the command fails to be executed due to insufficient ACL resources on the LPU.

Procedure

  1. Run the display current-configuration command to check whether the qos car inbound command is configured on each interface of the LPU in the log.
    • If so, go to step 2.
    • If not, go to step 5.
  2. Check whether the qos car inbound command needs to be configured on the interface.
    • If so, go to step 3.
    • If not, go to step 4.
  3. Run the undo eth-trunk command in the view of the member interface to delete the member interface from the Eth-Trunk and run the eth-trunk command to add the interface to the Eth-Trunk. Check whether qos car inbound is executed successfully.
    • If so, no action is required.
    • If not, go to step 5.
  4. Run the undo qos car inbound command on the interface to delete the configuration.
  5. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

QOSE/3/CMD_FAIL

Message

QOSE/3/CMD_FAIL:The command ([STRING1]) executed failed on slot [STRING2].

Description

The qos local-precedence-queue-map command fails to be executed on the LPU in the specified slot.

Parameters

Parameter Name Parameter Meaning
STRING1 Command that fails to be executed, that is, qos local-precedence-queue-map.
STRING2 Slot ID of the LPU.

Possible Causes

The qos local-precedence-queue-map command is executed on the LPU that does not support this command.

Procedure

  1. Check whether the LPU is required to support qos local-precedence-queue-map based on networking and service requirements.
    • If so, go to step 2.
    • If not, go to step 3.
  2. Use the LPU that supports qos local-precedence-queue-map to replace the existing one.

    NOTE:

    X series cards do not support qos local-precedence-queue-map.

  3. This message is informational only, and no action is required.

QOSE/4/CONGESTIONRISK

Message

QOSE/4/CONGESTIONRISK:There is a congestion risk on port [string].

Description

There is a congestion risk on an interface.

NOTE:

If the congestion risk of the interface is not eliminated, the system generates this log once an hour.

Parameters

Parameter Name Parameter Meaning
string Indicates the interface where there is a congestion risk.

Possible Causes

Burst traffic occurs on the interface.

Procedure

  1. Run the display qos queue statistics interface interface-type interface-number [ queue queue-index ] command on the interface involved in the log to check whether packets are discarded on the interface.
    • If so, go to step 3.
    • If not, go to step 2.
  2. Check whether the system generates this log again after one hour.
    • If so, go to step 3.
    • If not, it indicates that instantaneous burst traffic exists on the interface. This message is informational only and no action is required.
  3. Use one of the following methods to reduce burst traffic on the interface:

    • Run the qos burst-mode { enhanced | extreme } command on the interface to change the burst traffic buffering mode to enhanced.

    • Run the eth-trunk trunk-id [ mode { active | passive } ] command to add the interface to an Eth-Trunk to increase the interface bandwidth.

    Run the display qos queue statistics interface interface-type interface-number [ queue queue-index ] command on the interface to check whether packets are discarded and check whether the system generates this log again after one hour.

    • If so, go to step 4.
    • If not, it indicates that congestion risk of the interface is eliminated.
  4. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

QOSE/3/DEL_FAIL

Message

QOSE/3/DEL_FAIL:The command ([STRING1]) executed failed, the qos profile [STRING2] has been applied.

Description

The specified QoS profile is in use. As a result, the undo qos-profile all command fails to be executed.

Parameters

Parameter Name Parameter Meaning
STRING1 Command that fails to be executed, that is, undo qos-profile all.
STRING2 Name of a QoS profile.

Possible Causes

A QoS profile is in use when the undo qos-profile all command is executed to delete all QoS profiles.

Procedure

  1. When using the display qos-profile [ name profile-name | all ] command to check the brief information about all QoS profiles on the switch, check whether the QoS profile in the log is in use. If the value of Used is not 0, there are QoS profiles in use.
    • If so, go to step 2.
    • If not, go to step 5.
  2. Run the display this command in the AAA view to check whether the QoS profile is referenced in the service scheme.
    • If so, go to step 3.
    • If not, go to step 5.
  3. Check whether the QoS profile in use in the display qos-profile [ name profile-name | all ] command output is the same as the QoS profile referenced in the service scheme.
    • If so, go to step 4.
    • If not, go to step 5.
  4. This message is informational only and no action is required.
  5. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.

QOSE/3/STAT_FAIL

Message

QOSE/3/STAT_FAIL:Failed to execute ([STRING1]) due to insufficient resources in slot [STRING2].

Description

ACL resources are insufficient, and the statistic enable command fails to be executed in the specified VLAN on an LPU.

Parameters

Parameter Name Parameter Meaning
STRING1 Command that fails to be executed (that is, statistic enable) and ID of the VLAN where the command fails to be executed.
STRING2 Slot ID of the LPU.

Possible Causes

When the VLAN in the log is not created, the vlan vlan-id configuration command is used to enter the VLAN view and statistic enable is configured in the VLAN view. When the VLAN is created, the statistic enable command fails to be executed due to insufficient ACL resources on the LPU.

Procedure

  1. Run the display vlan command to check basic information about all created VLANs and check whether the traffic statistics function is enabled in a VLAN. When the value of Statistics is enable, the traffic statistics function is enabled in a VLAN.

    NOTE:

    Here, only the information that users need to focus on is displayed. The display vlan command output depends on the switch.

    <HUAWEI> display vlan
    ......
    VID  Status  Property      MAC-LRN Statistics Description
    --------------------------------------------------------------------------------
    1    enable  default       enable  disable    VLAN 0001
    9    enable  default       enable  enable     VLAN 0009
    40   enable  default       enable  enable     VLAN 0040
    50   enable  default       enable  disable    VLAN 0050

    • If so, go to step 2.
    • If not, go to step 5.
  2. Check whether the traffic statistics function is required in the corresponding VLAN based on service requirements.
    • If so, go to step 5.
    • If not, go to step 3.
  3. Enter the VLAN view and run the undo statistic enable command to disable the traffic statistics function.
  4. Delete the VLAN in the log and re-create it. Check whether a log indicating that the statistic enable command fails to be executed is generated.
    • If so, go to step 5.
    • If not, no action is required.
  5. Collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065665

Views: 5478

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next